ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Manuale utente
USER GUIDE
DISTRIBUTION PLATE
EKQuantum
Reflection2Torrent DDC 4.2 PWM D-RGB – Plexi
The installation of the product is intended to be undertaken by
an adequately trained and experienced person. You are installing
the product at your own risk. If you are not sufficiently trained
or experienced or feel unsure about the installation procedure,
please refrain from installing the product yourself and contact
our tech support for assistance. We disclaim our liability for any
damages to the product and incidental, consequential, or indirect
damages incurred due to improper or inappropriate installation.
Before you start using this product, please follow these basic guidelines:
Read this manual carefully before beginning the installation
process.
The EK-Quantum Torque fittings require only a tiny amount
of force to screw them firmly in place since the rubber O-ring
gaskets ensure the liquid seal.
Corrosion-inhibiting purpose-made coolants are always
recommended for any liquid cooling system. EK recommends
EK-CryoFuel coolants for worry-free usage.
- 3 -
TABLE OF CONTENT
BOX CONTENT 4
DISTRIBUTION PLATE DIMENSIONS 5
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS 6
PREPARING THE FRACTAL TORRENT CHASSIS 7
OPTIONAL: INSTALLING THE BOTTOM RADIATOR IN THE FRACTAL TORRENT CHASSIS 8
PREPARING THE EK-Quantum Reflection2Torrent DDC 4.2 PWM D-RGB DISTRIBUTION PLATE 9
INSTALLING THE EK-Quantum Reflection2Torrent DDC 4.2 PWM D-RGB DISTRIBUTION PLATE INTO CHASSIS 11
RECOMMENDED DISTRIBUTION PLATE CONFIGURATIONS 13
FLOW DIAGRAM 14
CONNECTING THE D-RGB LED STRIP 15
CONNECTING THE PUMP 15
TESTING THE LOOP 16
SUPPORT AND SERVICE 17
SOCIAL MEDIA 17
- 4 -
BOX CONTENT
8 mm
6 mm
4 mm
EK-Quantum Reflection2Torrent
DDC 4.2 PWM D-RGB – Plexi
Metal Radiator Bracket IDENT: 106328
M4 x 8 DIN7991 Screw (2 pcs
M4 x 6 DIN7984 Screw (2 pcs)
M4 x 4 DIN7984 Screw (6 pcs)
M4 x 0.8 Metal Washer (2 pcs)
2.5 mm Allen Key (1 pc)
EK-Loop Multi Allen Key (1 pc)
Mounting Mechanism: Reflection2Torrent DDC 4.2 PWM – IDENT: 105703
- 5 -
DISTRIBUTION PLATE DIMENSIONS
14 mm
56.8 mm
91.6 mm
111.9 mm
132.2 mm
161.6 mm
181.9 mm
202.2 mm
230.2 mm
258.2 mm
312 mm
333 mm
62 mm
62 mm
72 mm
80.4 mm
90.3 mm
118.3 mm
145.6 mm 40.4 mm
31.4 mm
27.4 mm27.4 mm
40.4 mm
31.4 mm
- 6 -
TECHNICAL SPECIFICATIONS AND PRODUCT PARTS
6
4
5
16
1
12
15
16
17
2
11
9
Technical Specification:
Dimensions with the attached pump (W x D x H): 145.6 x 40.4 x 333 mm
– D-RGB LED count: 18
– D-RGB cable length: 500 mm
– D-RGB connector: standard 3-pin (+5V, Data, Blocked, Ground)
Position EAN Description Quantity
1105689 TOP Plexi (Block part) 1
2105694 Inox Backplate 1
3105690 TOP Plexi (Lid part) 1
43831109837580 EK-DDC 4.2 PWM (12V SATA) 1
55154 OR 52 x 3 NBR50 1
69018 Screw M4 x 25 DIN7984 4
78207 Screw M4 x 14 DIN7991 33
8101556 LED D-RGB strip 500/300 mm 1
9102639 EK - Plug G1/4 9
10 105693 LED Cover (Black) 1
11 104599 Mylar sticker 1
12 8472 Screw M3 x 6 DIN7991 12
13 105697 OR - 216 x 2 1
14 105698 OR - 75 x 2 1
15 105699 OR - 151 x 2 1
16 105700 OR - 19 x 2 2
17 105701 OR - 85 x 2 1
18 105702 OR - 55 x 2 1
19 3831109834282 Plug cover (Acetal) 9
10
14
7
13
8
19
9
3
18
- 7 -
PREPARING THE FRACTAL TORRENT CHASSIS
STEP 1
Remove the front and side panels of your Fractal Torrent case.
STEP 2
Remove the front fans with upper and lower front bracket covers.
Then unscrew the bottom bracket thumb screws and carefully
pull them outside the case. If you are installing a bottom radiator,
remove all fans from the bottom of the case. Otherwise, you just
need to remove the one closest to the front panel.
Before inserting the EK-Quantum Reflection2 Torrent DDC 4.2
PWM D-RGB – Plexi distribution plate, you must remove all the
abovementioned elements.
STEP 1
STEP 2
Remove just
this fan if you
aren’t using
a bottom
radiator.
LOWER FRONT
BRACKET COVER
UPPER FRONT
BRACKET COVER
- 8 -
STEP 2
Once you have successfully pulled the bottom bracket outside the
chassis, mount the radiator and carefully tighten the screws without
completely fixing it in place. This step is crucial if you want to install
hard tubing without difficulties.
STEP 2
OPTIONAL: INSTALLING THE BOTTOM RADIATOR IN THE FRACTAL TORRENT CHASSIS
STEP 1 For this step, you need:
Important: These steps are to be followed if you are
using the EK-Quantum Surface P240 radiator and hard
tubing. 360mm or longer radiators cannot be used in the
bottom of the chassis when EK-Quantum Reflection2
Torrent DDC 4.2 PWM D-RGB distribution plate is
installed. Also note that EK-Loop Vertical GPU holder is
NOT compatible with the bottom radiator in this case.
STEP 1
Position the Quantum Surface fittings and end tank plugs as seen
in the image so that you can use tubing parallel to the longest side
of the radiator.
EK-Loop Multi Allen Key
- 9 -
STEP 3
Place the bottom bracket with the installed radiator inside the
chassis and tighten the thumb screws. After that, move the radiator
as far back as possible against the PCI slot brackets.
STEP 3
PREPARING THE EK-Quantum Reflection
2
Torrent DDC 4.2 PWM D-RGB DISTRIBUTION PLATE
STEP 1
STEP 1
Take the metal radiator bracket and tighten it on the EK-Quantum
Reflection2 Torrent DDC 4.2 PWM D-RGB distribution plate with two
(2) M4x8 DID7991 screws from the mounting mechanism packaging.
For this step, you need:
2.5 mm Allen Key
M4 x 8 DIN7991 SCREW
METAL R ADIATOR
BRACKET
- 10 -
STEP 2
Optional Step 2.1 (Using the Front and Bottom Radiator – GREEN)
Install the following in this sequence: EK-Quantum Torque Extender
Rotary MF 14mm, EK-Quantum Torque Angled – 90°, and EK-
Quantum Torque HTC fitting on the radiator port closer to the
distribution plate. EK-Torque HTC fittings should be installed on the
other radiator port and the bottom two distribution plate holes.
Optional Step 2.2 (Using the Front Radiator Only – RED):
Execute the previous “GREEN” steps with an additional EK-Quantum
Torque Extender Static MF 28mm for the radiator port further from
the distribution plate.
After either of these steps, push the radiator on the bracket with
ports on the bottom, as seen in the image. Make sure you cut the
tubes just right, with the position of the radiator matching the
screw holes on the metal bracket. We suggest the shorter tube be
51 mm and the longer one 107 mm. Once you’re finished with the
placement, tighten the radiator screws.
Important: Optional steps apply when using EK-
Quantum Surface P360 or P240 radiators, or in case of
S360 and S240 radiators when extra 14 mm extenders on
both radiator ports are needed.
STEP 2
TORQUE ROTARY
90° FITTING
14mm EXTENDER
28mm + 14mm
EXTENDER
FITTING
Altri manuali per EK-Quantum Reflection2 PC-O11D EVO D5 PWM...
3
Indice
Altri manuali ekwb Hardware per computer
ekwb
ekwb EK-FCW9000 Guida
ekwb
ekwb EK H30 SUPREME Manuale utente
ekwb
ekwb EK-Quantum Reflection Uni 140 D5 PWM D-RGB Manuale utente
ekwb
ekwb EK-FC R9 290X DCII Guida
ekwb
ekwb EK-FB EVGA X58 CLASSIFIED Manuale utente
ekwb
ekwb EK-Quantum Momentum Aorus Z490 Master D-RGB Manuale utente
ekwb
ekwb EK-PRO GPU WB RTX A4090 Manuale utente
ekwb
ekwb EK-FB ASUS Max4 Extreme Guida
ekwb
ekwb EK-Classic 115 D-RGB Series Manuale utente
ekwb
ekwb EK-FC980 GTX TF5 Manuale
ekwb
ekwb EK-FC670 GTX DCII Guida
ekwb
ekwb EK-Vector Strix RTX 2070 Backplate Guida
ekwb
ekwb EK-Supremacy EVO X99 Series Manuale utente
ekwb
ekwb EK-FC780 GTX Ti Manuale
ekwb
ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manuale utente
ekwb
ekwb EK-FB ASUS PRIME X299 RGB Monoblock Manuale utente
ekwb
ekwb EK-XTOP D5 Guida
ekwb
ekwb EK-XRES DCP 2.2 Reservoir Manuale
ekwb
ekwb EK-FB ASUS P7P55 KIT Guida
ekwb
ekwb EK-Quantum Vector2 Trio RTX 3080/90 ABP Set... Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
