Ekwb EK-Vector Strix RTX 2070 Backplate Guida

All disclosures, notices and warranty conditions are being written on the back of the box.

Installation and mounting manual for EK-Vector Strix RTX 2070

Backplate

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability

whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before

installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

STEP 1: GENERAL INFORMATION. Sample picture of ROG Strix GeForce RTX 2070 graphics card.

STEP 2: PREPARING YOUR GRAPHICS CARD

EK-Vector Strix RTX 2070 Backplate is very easy to install. First install EK-Vector Strix RTX 2070 series water block according to its installation manual. If you

have it already installed, please check the picture below to see which mounting screws are to be left in their position and which should be removed. Please

remove the six (6) M2.5x4 AX1 screws and their PVC washers as well (marked with arrow).

STEP 3: APPLYING THE THERMAL PADS

EK-Vector Strix RTX 2070 Backplate features passive cooling of the printed circuit board and its components therefore it is mandatory to install the

enclosed thermal pad. Please install enclosed 1,5mm and 1mm thick thermal pads (Thermal Pad G –1,5mm (120x24) & Thermal pad F –1mm

(120x16)) as shown on the picture below. You may need to trim the excess thermal pad.

Thermal PAD G –1,5mm (120x24mm)

EK-Vector Strix RTX 2070 Backplate

Thermal PAD F –1mm (120x16mm)

All disclosures, notices and warranty conditions are being written on the back of the box.

STEP 4: ATTACHING EK-VECTOR STRIX RTX 2070 BACKPLATE TO THE GRAPHICS CARD

Take enclosed mounting screws and install them as shown on picture below. Use six (6) M2.5x7 AX1 screws, and tighten them using Philips head screwdriver.

HINT: Do not tighten screws until they are all positioned in their mounting holes. The backplate has milled in standoffs, so there is no fear of over tightening of

the screws. Nevertheless do not exaggerate with screwing force as there is no need for it.

By all means users must also consider that this product is intended to be used only with EK-Vector Strix RTX 2070 series water blocks. No other 3rd party heat

sinks or coolers are officially supported! EK does not offer any assistance or support in the latter application.

IMPORTANT DISCLOSURES

VERY IMPORTANT NOTICE: Once the installation is completed, it is a recommended practice to test the cooling circuit for leaks prior to powering up the

computer. We recommend a 24 hour leak test prior to powering up the computer. Do not test the water block using city water pressure. This will rupture the top

of the housing and render the block unusable (and will void your warranty).While all efforts have been made to provide the most comprehensive tutorial possible,

EK Water Blocks assumes no liability expressed or implied for any consequential damage(s) occurring to your equipment as a result of using EK Water Blocks

cooling products, either due to errors or omissions on our part in the above instructions, or due to failure or defect in the EK Water Blocks cooling products.

WARRANTY:

Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user. During

this period, products will be repaired or have parts replaced at our discretion provided that: (I) the product is returned to the agent from whom it was purchased;

(II) the product has been purchased by an end user and has not used for commercial purposes; (III) the product has not been misused, handled carelessly, or

used in a manner other than in accordance with the instructions provided describing its installation and proper use. This warranty does not confer rights other

than those expressly set out above and does not cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and does not

affect your statutory rights as a consumer. This warranty is voided if the product comes in contact with aggressive UV additives or other improper liquids.

EK blocks are sealed with warranty void circular label, which proves that the block has withstood a pressure leak test. Removing it will void leak-free guarantee

and not the guarantee on the product itself. Any other RMA issues can be reported to EK Support at http://www.ekwb.com/support for further analysis.

REQUIRED TOOLS AND MOUNTING SCREWS:

Philips head screwdriver scissors

M2.5x7 AX1

Indice

Altri manuali ekwb Hardware per computer

ekwb

ekwb EK-FB KIT GA-X99 SOC Champion Series Manuale

ekwb

ekwb EK-FC980 GTX Strix Manuale

ekwb

ekwb EK-FC Titan XXL Manuale

ekwb

ekwb EK-FC970 GTX TF5 TFX Series Manuale

ekwb

ekwb EK-Quantum Reflection2 PC-O11D EVO D5 PWM... Manuale utente

ekwb

ekwb EK-Quantum Volume FLT Series Manuale utente

ekwb

ekwb EK-Pro GPU WB RTX 8000 - Ni + Inox Manuale utente

ekwb

ekwb EK-Quantum Vector RE RTX 3080 Active Backplate... Manuale utente

ekwb

ekwb EK-FC560 GTX Manuale

ekwb

ekwb EK-Quantum Velocity 2 Manuale utente

ekwb

ekwb EK-XTOP D5 Manuale

ekwb

ekwb Classic D-RGB S240 Manuale utente

ekwb

ekwb EK-FC 780 GTX DCII Original CSQ Manuale

ekwb

ekwb EK-FB GA X470 Gaming 7 RGB Manuale utente

ekwb

ekwb 3831109891452 Manuale utente

ekwb

ekwb EK-Pro CPU Water Block SP5 Manuale utente

ekwb

ekwb EK-FCS10000 Manuale

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 D-RGB Manuale utente

ekwb

ekwb EK-SF3D Inflection Point EVO Manuale utente

ekwb

ekwb EK-Quantum Momentum Aorus Z490 Master D-RGB Manuale utente

ekwb

ekwb EK-Quantum Vector Trinity RTX 3080/3090 Manuale utente

ekwb

ekwb EK-Classic AM4 D-RGB Manuale utente

ekwb

ekwb EK-DBAY DCP 2.2 Manuale

ekwb

ekwb EK-MOSFET ASUS M6G Guida

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

ekwb EK-Vector Strix RTX 2070 Backplate Guida

Manuali Hardware per computer popolari di altre marche