Ekwb EK-Quantum Velocity 2 Manuale utente

USER GUIDE

EK-Quantum

Velocity² - AM5 Backplate

Please note the installation of the product is intended to be undertaken

by an adequately trained and experienced person. You are installing the

product at your own risk. If you are not properly trained or experienced or

feel unsure about the installation procedure, please refrain from installing

the product yourself and contact our tech support for assistance. We

disclaim our liability for any damages to the product as well as incidental,

consequential, or indirect damages incurred due to improper or

inappropriate installation.

Before you start using this product, please follow these basic guidelines:

Please carefully read the manual before beginning the

installation process.

The EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the

rubber O-ring gaskets.

The use of corrosion inhibiting coolants is always recommended

for liquid cooling systems, and mandatory for nickel-plated

water blocks.

Do not use pure distilled water! For best results, EK recommends

the use of EK-Cryo Fuel coolants.

Make sure to thoroughly bleed air out of your water block, or

you will not reach optimal performance.

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

BACKPLATE DIMENSIONS 5

PREPARING THE AM4 WATER BLOCK FOR UPGRADE 6

PREPARING THE AM5 MOTHERBOARD 7

INSTALLING THE WATER BLOCK 9

CONNECTING THE D-RGB LED STRIP 11

TESTING THE LOOP 11

WARRANTY 12

SUPPORT AND SERVICE 13

SOCIAL MEDIA 13

- 4 -

BOX CONTENTS

AM5 Backplate

Allen Key 2.5 mm (1 pc) TX20 L-Shaped Wrench (1 pc)

Thermal grease (1 pc)

- 5 -

BACKPLATE DIMENSIONS

90 mm

60 mm

43 mm

53 mm

8.9 mm

7.6 mm

6.3 mm

- 6 -

STEP 1

TOP OF THE

MOTHERBOARD

PREPARING THE AM4 WATER BLOCK FOR UPGRADE

Important! Before starting, make sure to have a clean, ﬂat

surface to work on. It is recommended to put foam or soft

material to lay a motherboard on.

STEP 1

If the EK-Quantum Velocity2 AM4 water block is already installed,

remove the backplate from the motherboard’s backside using Allen

Key 2.5 mm (As shown in the picture).

STEP 2

Detach the water block from the motherboard and save it for later

steps. Clean the CPU cold plate using a non-abrasive cloth or Q-tip.

STEP 2

- 7 -

STEP 1

Using a Philips-head screwdriver remove the four screws securing

the original plastic hold-down clamps around the socket as shown in

the illustration. Remove the hold-down clamps and store them away.

PREPARING THE AM5 MOTHERBOARD

UNC 6-32 SCREW

HOLD-DOWN

CLAMPS

STEP 1

STEP 2

After removing the plastic hold-downs, additional four (4) Screws

must be removed using provided TX20 L-shaped wrench. After

removing the screws, detach the factory-provided backplate. Save

the backplate screws for the next step.

STEP 2

BACKPLATE SCREW

FACTORY-PROVIDED

BAC KP L ATE

TX20 L-Shaped Wrench

For this step, you will need:

- 8 -

STEP 3

Attach the AM5 Backplate and secure it with the four (4) saved

backplate screws.

Do not peel off the protective sticker from the AM5 Backplate!

STEP 4

Cleaning the CPU: Wipe the IHS clean using a non-abrasive cloth or

Q-tip as shown in the illustration.

STEP 3

STEP 4

IHS

NON-ABRASIVE CLOTH

AM5 BAC KP L ATE

BAC KP L ATE

SCREW

TX20 L-Shaped

Wrench

AM5 Backplate

Backplate screw

(4 pcs)

For this step, you will need:

- 9 -

STEP 1

Position the AM4 CPU Water Block onto the AM5 Motherboard.

Make sure to align the holes (as shown in the picture).

Make sure to double-check the layer of the Thermal Grease

before placing the water block onto the motherboard.

STEP 1

INSTALLING THE WATER BLOCK

STEP 5

Applying thermal compound: Apply the enclosed thermal grease

(thermal compound) on the CPU heat spreader – IHS – as shown in

the image. The layer of the thermal compound must be thin and even

in thickness over the entire surface of the IHS.

The excessive or uneven application of thermal grease

may lead to poor performance!

STEP 5

Thermal Grease

For this step, you will need:

- 10 -

STEP 3

With EK-Velocity² series water blocks, it is mandatory to use the

bottom port as the INLET.

Mixing the ports may result in poor thermal performance of the

water block.

Tighten the ﬁttings in a clockwise direction until the gasket

underneath is compressed. The installation of the Velocity² water

block is now complete.

OUTLET

INLET

STEP 2

Secure the water block from the backside of the motherboard using

the included Allen Key 2.5mm.

Start fastening the screws in a cross pattern. Do not tighten fully until

all of the screws are partially screwed in.

The Allen Key 2.5mm must be used in a standing position! Otherwise,

the mounting screws may crack during tightening!

Make sure to orientate the backplate as illustrated. Incorrect

installation of the backplate may result in damage to the motherboard.

Allen Key 2.5 mm

For this step, you will need:

MAX TORQUE:

0.6 Nm TOP OF THE

MOTHERBOARD

AM5

BAC KP L ATE

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ekwb Hardware per computer

ekwb

ekwb EK-FC Titan XXL Manuale

ekwb

ekwb EK-MOSFET ASUS M7G Guida

ekwb

ekwb EK-Quantum Reflection PC-O11D D5 PWM D-RGB Manuale utente

ekwb

ekwb EK-FC 6970 Manuale

ekwb

ekwb EK-FC980 GTX Guida

ekwb

ekwb EK-FB ASUS PRIME X299 Monoblock Manuale utente

ekwb

ekwb EK-FC4890LT Guida

ekwb

ekwb EK-FB GA X470 Gaming 7 RGB Manuale utente

ekwb

ekwb EK-FC R9 Fury X Guida

ekwb

ekwb EK-MOSFET ASUS M6G Guida

ekwb

ekwb EK-Quantum Vector Aorus RTX 2080 Ti Manuale utente

ekwb

ekwb EK-FC1080 GTX JetStream Backplate Guida

ekwb

ekwb EK-FC480 GTX Manuale

ekwb

ekwb EK-FB GA AMD KIT Manuale

ekwb

ekwb Velocity Manuale utente

ekwb

ekwb EK-Dual DDC X-Top CSQ Manuale

ekwb

ekwb Ultra Monoblock EK-FB GA X99 Manuale utente

ekwb

ekwb EK-BAY DCP 2.2 Manuale

ekwb

ekwb EK-Quantum Momentum2 ROG Strix Z690-I Gaming D-RGB -... Manuale utente

ekwb

ekwb EK-FC690 Guida

ekwb

ekwb EK-SB ASUS M6G Guida

ekwb

ekwb EK-FC 6970 V2 Manuale

ekwb

ekwb EK-FC1080 GTX JetStream Manuale utente

ekwb

ekwb EK-FB ASUS R4BE Monoblock Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

ekwb EK-Quantum Velocity 2 Manuale utente

Manuali Hardware per computer popolari di altre marche