Ekwb EK-Vector FTW3 RTX 2080 Ti Guida

All disclosures, notices and warranty conditions are being written on the back of the box.

Installation and mounting manual for EK-Vector FTW3 RTX 2080 Ti

Backplate:

This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water

Blocks assumes no liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our

web site at www.ekwb.com for updates. Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.

STEP 1: GENERAL INFORMATION. Sample picture of FTW3 RTX 2080 Ti graphics card.

STEP 2: PREPARING YOUR GRAPHICS CARD

First install EK-Vector FTW3 RTX 2080 Ti series water block according to its installation manual. If you have it already installed, please

check the picture below to see which mounting screws are to be left in their position and which are to be removed. Please remove the six (6)

M2.5x4 AX1 screws and their PVC washers as well (marked with arrow).

STEP 3: APPLYING THE THERMAL PADS

EK-Vector FTW3 RTX 2080 Ti features passive cooling of the printed circuit board and its components therefore it is mandatory to install the

enclosed thermal pad. Please install (Thermal Pad F –1,0mm (120x16)) and (Thermal Pad F –1.5mm (120x16)) as shown on the picture below.

You may need to trim the excess thermal pad.

PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION!

1. Thermal Pad F 1.0mm (EAN: 3830046996732)

2. Thermal Pad F 1.5mm (EAN: 3830046996749)

EK-VECTOR FTW3 RTX

2080Ti BACKPLATE

All disclosures, notices and warranty conditions are being written on the back of the box.

STEP 4: ATTACHING EK-Vector FTW3 RTX 2080 Ti TO THE GRAPHICS CARD

Take enclosed mounting screws and install them as shown on picture below. Use six (6) M2.5x7 AX1 screws, and tighten them using Philips head

screwdriver.

HINT: Do not tighten screws until they are all positioned in their mounting holes. The backplate has milled in standoffs, so there is no fear of over

tightening of the screws. Nevertheless do not exaggerate with screwing force as there is no need for it.

By all means users must also consider that this product is intended to be used only with EK-Vector FTW3 RTX 2080 Ti series water blocks. No

other 3rd party heat sinks or coolers are officially supported! EK does not offer any assistance or support in the latter application.

IMPORTANT DISCLOSURES

VERY IMPORTANT NOTICE: Once the installation is completed, it is a recommended practice to test the cooling circuit for leaks prior to powering

up the computer. We recommend a 24 hour leak test prior to powering up the computer. Do not test the water block using city water pressure.

This will rupture the top of the housing and render the block unusable (and will void your warranty).While all efforts have been made to provide

the most comprehensive tutorial possible, EK Water Blocks assumes no liability expressed or implied for any consequential damage(s) occurring to

your equipment as a result of using EK Water Blocks cooling products, either due to errors or omissions on our part in the above instructions, or

due to failure or defect in the EK Water Blocks cooling products.

WARRANTY:

Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final

user. During this period, products will be repaired or have parts replaced at our discretion provided that: (I) the product is returned to the agent

from whom it was purchased; (II) the product has been purchased by an end user and has not used for commercial purposes; (III) the product

has not been misused, handled carelessly, or used in a manner other than in accordance with the instructions provided describing its installation

and proper use. This warranty does not confer rights other than those expressly set out above and does not cover any claims for consequential loss

or damage. This warranty is offered as an extra benefit and does not affect your statutory rights as a consumer. This warranty is voided if the

product comes in contact with aggressive UV additives or other improper liquids. EK blocks are sealed with warranty void circular label, which proves

that the block has withstood a pressure leak test. Removing it will void leak-free guarantee and not the guarantee on the product itself. Any other

RMA issues can be reported to EK Support at http://www.ekwb.com/support for further analysis.

REQUIRED TOOLS AND MOUNTING SCREWS:

Philips head screwdriver scissors

M2.5X7 AX1 Screw

Phillips head

screwdriver

Altri manuali per EK-Vector FTW3 RTX 2080 Ti

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ekwb Hardware per computer

ekwb

ekwb EK-FB KIT GA P67A UD7 Manuale

ekwb

ekwb EK-FC1070 GTX Manuale utente

ekwb

ekwb EK-Annihilator Series Manuale utente

ekwb

ekwb Barebones Guida

ekwb

ekwb EK-FC780 Guida

ekwb

ekwb EK-FB EVGA CLASSIFIED 4-SLI Guida

ekwb

ekwb EK-Quantum Magnitude Manuale utente

ekwb

ekwb EK-Classic 115x/20xx D-RGB Manuale utente

ekwb

ekwb EK-FC5x0 GW GTX water block Manuale

ekwb

ekwb EK-FC R9-290X SE Backplate Guida

ekwb

ekwb EK-FC R9-295X2 Guida

ekwb

ekwb EK-PRO GPU WB AMP-Trinity RTX 4090 Ni+Inox Manuale utente

ekwb

ekwb EK-XRES 140 Revo D5 Series Guida

ekwb

ekwb EK-FC690 Guida

ekwb

ekwb EK-FC Strix RTX 2080 Ti Backplate Classic Guida

ekwb

ekwb ASUS Z9PE-D8 Manuale utente

ekwb

ekwb EK-FC R9 Nano Series Manuale

ekwb

ekwb EK-Quantum Momentum VRM Bridge ROG Maximus XII Formula D-RGB -... Manuale utente

ekwb

ekwb EK-Quantum Momentum Aorus X570 Master D-RGB -... Manuale utente

ekwb

ekwb EK-FB MSI X370 XPower Monoblock Manuale utente

ekwb

ekwb Supremacy EVO Manuale utente

ekwb

ekwb EK-Quantum Momentum Aorus Z490 Master D-RGB Manuale utente

ekwb

ekwb EK-FC980 GTX Ti Classy KPE Series Manuale

ekwb

ekwb EK-Quantum Momentum Aorus Z490 Master D-RGB Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

ekwb EK-Vector FTW3 RTX 2080 Ti Guida

Manuali Hardware per computer popolari di altre marche