Elatec MultiTech M TWN4 Manuale utente

RFID Reader/ Writer

TWN4 MultiTech M

User Manual

Elatec GmbH

Page 2 of 13

1. Introduction

The transponder reader module TWN4 MultiTech M is a device for reading

and writing RFID transponders. There are different versions of TWN4

devices available, which cover a large range of transponder types both in

the frequency range of 125kHz and 13.56MHz.

2. Getting Started

2.1 Cable Connection

In order to start operating a TWN4 transponder reader, it simply has to be

connected to a host.

2.2 Enumeration

Once the device has been powered up, it is waiting for completion of the

enumeration by the USB host. As long as the device is not enumerated, it is

entering a minimum power consumption mode, where both LEDs are

turned off.

2.3 Initialization

After powering up and enumeration, the device is turning on the built-in

transponder reader logic. The green LED is turned on permanently. Some

transponder readers need some kind of initialization, which is performed in

Elatec GmbH

Page 3 of 13

this step. After successful initialization, the device sounds a short sequence,

which consists of a lower tone followed by a higher tone.

2.4 Normal Operation

As soon as the device has completed the initialization, it is entering normal

operation. During normal operation the device is searching for a

transponder continuously.

Detection of a Transponder

If a transponder is detected by the reader, following actions are performed

Send the ID to the host. By default, the USB device sends by

emulating keystrokes of a keyboard.

Sound a beep

Turn off the green LED

Blink the red LED for two seconds

Turn on the green LED

Within the two seconds timeout, where the red LED is blinking, the

transponder, which just has been recognized will not be accepted again.

This prevents the reader from sending identical IDs more than one time to

the host.

If during the two seconds timeout of the red LED a different transponder is

detected, the complete sequence restarts immediately.

Elatec GmbH

Page 4 of 13

Suspend Mode

The transponder reader supports the USB suspend mode. If the USB host

is signaling suspend via the USB bus, the transponder reader is turning off

most of its power consuming peripherals. During this operation mode, no

detection of transponders is possible and all LEDs are turned off.

Once the host is resuming to normal operation mode, this is also signaled

via the USB bus. Therefore, the transponder reader will resume to normal

operation, too.

Elatec GmbH

Page 5 of 13

3. List of Antennas

HF antenna

LF antenna

Elatec GmbH

Page 6 of 13

4. Compliance statements

FCC

(RF module)

Compliance statement:

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Modification of equipment:

The instruction manual of the host shall include the following statement:

Changes or modifications made to this equipment not expressly approved

by the party responsible for compliance may void the FCC authorization to

operate this equipment.

Information to the user:

(The instruction manual of the host shall include the following statement) A

compliance statement as applicable, e.g., for devices subject to part 15 of

CFR 47 as specified in §15.19(a)(3), that the product complies with the

rules; and the identification, by name, address and telephone number or

Internet contact information, of the responsible party, as defined in §2.909.

The responsible party for Supplier’s Declaration of Conformity must be

located within the United States.

Elatec GmbH

Page 7 of 13

Host devices

FCC notes for a host subject to verification or SDoC:

For a host device assembled with the certified module and subject to 47

CFR Part 15 verification of class A digital devices, the following statements

have to be included in the user manual and the host device has to be

labelled as noted below. If the host device is subject to other authorization

procedures or parts the appropriate requirements of these authorization

procedures or parts apply.

Important note:

OEM integrator is still responsible for the FCC compliance requirements of

the end product, which integrates this module. Appropriate measurements

(e.g. 15B compliance) and if applicable additional equipment authorization

of the host device to be addressed by the integrator/ manufacturer

The end device must be labeled with:

Contains FCC ID: WP5TWN4F17

Contains IC: 7948A-TWN4F17

HVIN: EL20208

Elatec GmbH

Page 8 of 13

Example for SDoC:

The compliance information statement shall be included in the user's

manual or as a separate sheet. In cases where the manual is provided only

in a form other than paper, such as on a computer disk or over the Internet,

the information required by this section may be included in the manual in

that alternative form, provided the user can reasonably be expected to have

the capability to access information in that form. The information may be

provided electronically as permitted in §2.935.

Elatec GmbH

Page 9 of 13

NOTE: The Commission does not have a required SDoC format. This is an

example only and is provided to illustrate the type of information that may

be supplied with the product at the time of marketing or importation for

meeting the FCC SDoC requirement.

For class B devices:

FCC §15.105 (b):

Note: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the Receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Elatec GmbH

Page 10 of 13

For class A devices:

FCC §15.105 (b):

NOTE: This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own

expense.

CANADA:

This device complies with Industry Canada’s license-exempt RSSs.

Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that

may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables

aux appareils radio exempts de licence. L’exploitation est autorisée aux

deux conditions suivantes:

1) l’appareil ne doit pas produire de brouillage;

2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Special accessories:

Where special accessories such as shielded cables and/or special

connectors are required to comply with the emission limits, the instruction

manual shall include appropriate instructions on the first page of the text

describing the installation of the device.

Simultaneous transmission:

When the host product supports simultaneous-transmission operations the

host manufacturer needs to check if there are additional RF exposure filing

requirements due to the simultaneous transmissions. When additional

Indice

Altri manuali Elatec Sistema RFID

Elatec

Elatec TWN4 PALON COMPACT M Manuale utente

Elatec

Elatec TWN4 MultiTech 2 HF Manuale per l'uso e la cura

Elatec

Elatec TWN4 MULTITECH NANO LEGIC 63 M Manuale utente

Elatec

Elatec TWN4 Slim LEGIC Manuale utente

Elatec

Elatec TWN4 MultiTech LEGIC 42 Manuale utente

Elatec

Elatec MULTITECH 2 M HF Manuale utente

Elatec

Elatec TWN4 MultiTech 2 HF Manuale utente

Elatec

Elatec TWN3 Mini Reader Mifare NFC Manuale utente

Elatec

Elatec TWN4 MultiTech 2 HF Manuale utente

Elatec

Elatec TWN4 MultiTech 2 HF Manuale utente

Elatec

Elatec TWN4 MultiTech 2 HF Manuale utente

Elatec

Elatec TWN4 MultiTech 2 HF Manuale utente

Elatec

Elatec TWN4 MultiTech 2 HF Manuale utente

Elatec

Elatec TWN4 MultiTech 3 LEGIC M BLE Manuale utente

Elatec

Elatec TWN4 MultiTech 2 HF Manuale utente

Elatec

Elatec TWN3 MIFARE Manuale utente

Elatec

Elatec TWN4 Palon Compact LEGIC Manuale per l'uso e la cura

Elatec

Elatec TWN4 MultiTech 2 HF Manuale utente

Elatec

Elatec MULTITECH 2 LEGIC M Manuale utente

Elatec

Elatec TWN4 MULTITECH 3 LEGIC M LF HF Manuale utente

Elatec

Elatec MULTITECH 2 LEGIC M Manuale utente

Elatec

Elatec TCPConv Manuale utente

Elatec

Elatec TWN4 MultiTech 3 BLE Nota di rilascio

Elatec

Elatec TWN4 MultiTech 2 HF Manuale utente

Manuali Sistema RFID popolari di altre marche

Chainway

Chainway R1 Manuale utente

IFM

IFM DTC600 Manuale utente

RHOMBUS

RHOMBUS DR20 Manuale utente

Sirit

Sirit IDentity 6204 Manuale utente

SOREX

SOREX FLEX Manuale utente

Omron

Omron V780-HMD68-EIP-KR Manuale utente

IDENTEC SOLUTIONS

IDENTEC SOLUTIONS iPOINT Si Istruzioni per l’uso

Shuttle

Shuttle BR06 Istruzioni utente

Digilock

Digilock Curve Keypad Basic Manuale utente

Atid

Atid AT870 Manuale utente

Chacon

Chacon 34958 Manuale utente

Paxton

Paxton PROXIMITY architectural reader Manuale utente

CipherLab

CipherLab 1800 series Manuale utente

Brady

Brady FR22 Manuale utente

Kronotech

Kronotech BLUEBOX GEN2 M30 UHF Manuale utente

Unitech

Unitech RH767 Manuale utente

Honeywell

Honeywell 026366.00 Manuale utente

OLIMEX

OLIMEX MOD-RFID125-BOX Manuale utente