Electro-Voice R300HDC Manuale utente
UHF WIRELESS MICROPHONE
USER GUIDE
R300
SYNC
R300
EZsync Clear
SET
LE
N
NAHC
ETU
M
C
N
YS
MHz
EZsync ClearScan
Electro-Voice
R
300
1177
2
3
TAB LE OF CONTENTS
1. Quick Set–up
• Receiver.................................................................................................................4
• Transmitter.............................................................................................................5
• Systems Operation..............................................................................................6
2. Detailed Component Descriptions
• Receiver.......................................................................................................... 7-14
• Handheld Transmitter .................................................................................15-16
• Bodypack Transmitter................................................................................. 17-19
3. Guidelines and Recommendations For Best Performance ...............................20-21
4. Troubleshooting Guide .............................................................................................22-23
5. Frequently Asked Questions ...................................................................................24-26
6. Components and Accessories...................................................................................... 27
7. Compatible Channel Frequency Groups...............................................................28-31
8. Specifications ............................................................................................................32-33
9. Certifications..................................................................................................................... 34
10. Factory Service ................................................................................................................ 35
4
01QUICK SETUP: RECEIVER
1. Do not connect the receiver to any other equipment yet!
2. Connect the two Antennas to the receiver.
3. Install the blades into the power supply, plug it into the back of the receiver,
and into an outlet.
4. Press the POWER switch. Display will light up.
5. Press and hold the button until CLEARSCAN scrolls across the screen.
6. When CLEARSCAN stops, the receiver will be set to the clearest channel.
7. Mute the Audio Mixer channel where the receiver will be plugged in, or set it to minimum.
8. Leave the receiver ON and connect it to the audio system using either the XLR connector or
¼-inch line level jack.
Receiver “Quick Set-up” is complete.
5
QUICK SETUP: TRANSMITTER
1. With the Power switch on the transmitter OFF, install two fresh AA batteries into the transmitter.
2. Press the transmitter Power Switch until the display comes on.
3. Loosen the transmitter battery cover to expose the EZsync Port, as shown.
4. Hold the transmitter with the EZsync Port facing the receiver, about a
foot (30 cm) away.*
5. Press the SYNC Button on the receiver, SYNC will show in the display.
6. Once the channel is set in the transmitter, the display will switch to the main
display and show RF and Audio Levels.
*Note: When performing EZsync, make sure lighting conditions are not too bright. Extremely
bright lighting can interfere with EZsync.
Transmitter “Quick Set-up” is complete.
SYNC
R300
EZsync Clear
SET
SYNC
EZsync
R300 ClearScan
SET
CHANNEL
MUTE
SYNC
MHz
6
QUICK SETUP: SYSTEMS OPERATION
1. Set the mixer/amp gain.
2. Talk or sing into the microphone or play the guitar at a normal volume. You
should hear audio coming out of the system.
3. You may have to adjust the gain (via the control next to the connector on the
receiver back panel) to provide the best input volume for your mixer/amp.
Notes:
• See page 10 of this manual for more information.
• See Image 11 of the Quick Start Guide for gain control location.
“Quick Set-up” is now complete. Please enjoy your R300 system.
01
7
SYNC
R300
EZsync Clear
SET
EZsync ClearScan
Electro-Voice
R
300
ANTENNA B ANTENNA A12V .500mA
MIN MAX
VOLUME
LEVEL
-10dB 0dB
BALANCED OUT UNBALANCED OUT
DETAILED COMPONENT DESCRIPTIONS
2.1 |R300 Receiver
RECEIVER CONTROLS, CONNECTORS
1. Power ON/OFF
2. SYNC Data Transfer Button
3. Infrared EZsync Window
4. Graphical Display
a. Channel or Frequency Display
b. Diversity Indicator
c. RF Strength Meter
d. Audio Level Meter
e. Lock Indicator
f. Squelch Level Indicator
5. Scroll Down and Up ( and ) Control Buttons
6. SET Control Button
7. ClearScan Control (press and hold button)
8. TNC Antenna Input Connectors (2)
9. Audio Output Volume Control
10. XLR Balanced Output Connector
11. ¼ Inch Unbalanced Line Level Audio Output Connector
12. Unbalanced Output Level Switch (-10dB or 0dB)
13. DC Power Connector (12V DC, 500mA)
14. Power Cord Retainer
02
8 89 10 11 12 13 14
8
DETAILED COMPONENT DESCRIPTIONS
2.1 |Receiver Setup & Operation
1. Place the receiver and antennas where there is a clear line of sight to the area where the
transmitter will be used. Rotate the antennas to separate them by 90 degrees.
2. Install the appropriate power connection blades into the power supply and connect
the power supply cord to the receiver. Plug the power supply into an AC outlet. Push
the power button to turn the receiver on and confirm that it is on by checking the main display
screen.
3. Manual Channel Change
a. The and buttons allow you to scroll through the Channels. When the Channel
you desire is displayed, stop scrolling.
b. After 2 seconds the displayed channel number will start to flash.
c. The number will stop flashing and the new channel is installed.
d. Turn on the transmitter and hold the EZsync port facing the receiver EZSync port,
about a foot (30 cm) away, as described on page 5.
02
ANTENNA B ANTENNA A12V .500mA
MIN MAX
VOLUME
LEVEL
-10dB 0dB
BALANCED OUT UNBALANCED OUT
continued on next page
9
e. Press the SYNC button on the receiver to transfer the channel information.
f. The receiver will display SYNC until the data is transferred, then return to the main screen.
g. The transmitter display screen will now show the new channel and frequency.
NOTE:
1. If the channel data was not transferred to the transmitter after 5 seconds, the receiver
will display ERROR. Be certain that the transmitter is On and the EZsync port is facing
the receiver and try again.
2. If the data still does not transfer, try new batteries, or move the unit to a shaded area
away from direct sunlight or bright lights before trying again.
R300 ClearScan
SET
CHANNEL
MUTE
SYNC
MHz
SYNC
R300
EZsync Clear
SET
SYNC
EZsync
continued on next page
10
DETAILED COMPONENT DESCRIPTIONS
4. ClearScan: This feature automates the process of finding a clear channel.
a. To scan for the clearest channel in a group, press and hold until CLEARSCAN
appears in the display, then release the button.
b. When the scan is complete, the display will show the clearest available channel.
c. Use the SYNC button to transfer the new channel as in step 3.
5. During set up make sure the mixer or amplifier input used for the R300 is muted or turned down
to a minimum level.
6. Plug an audio cable (not supplied) into the 3 pin XLR or ¼-inch TRS output of the R300.
Note: The XLR connector is the preferred connection since the output is balanced and will be
more immune to noise for longer runs of cable although either can be used with good
results. Set the balanced output level on the back panel to 12 o’clock (midway in the
range) to start and adjust later if necessary. If the ¼-inch unbalanced output is used, start
with adjustment switch in the -10dB setting.
02
continued on next page
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali Electro-Voice Microfono
Electro-Voice
Electro-Voice ENG 618 Manuale utente
Electro-Voice
Electro-Voice 205C Manuale utente
Electro-Voice
Electro-Voice N868 Manuale utente
Electro-Voice
Electro-Voice Cobalt Co7 Manuale utente
Electro-Voice
Electro-Voice HM1 Manuale utente
Electro-Voice
Electro-Voice HM1 Manuale utente
Electro-Voice
Electro-Voice PolarChoice PC-12 Manuale utente
Electro-Voice
Electro-Voice CS11 Manuale utente
Electro-Voice
Electro-Voice N/D267 Manuale utente
Electro-Voice
Electro-Voice PL4 Manuale utente
Electro-Voice
Electro-Voice N/D767a Manuale utente
Electro-Voice
Electro-Voice 1776A Manuale utente
Electro-Voice
Electro-Voice DS35 Manuale utente
Electro-Voice
Electro-Voice N/D868 Manuale utente
Electro-Voice
Electro-Voice PolarChoice Desktop Series Manuale utente
Electro-Voice
Electro-Voice ULM-21 Manuale utente
Electro-Voice
Electro-Voice MC300 Manuale utente
Electro-Voice
Electro-Voice N478 Manuale utente
Electro-Voice
Electro-Voice RE50/B Manuale utente
Electro-Voice
Electro-Voice PL78 Manuale utente
