Electrolux ESE5300PD-VN Manuale utente
Item PNC ELC Brand Model Market
Electrolux Thailand Co.,Ltd.
1910 Electrolux Building
New Petchburi Rd. Bangkapi
Huaykwang Bangkok , 10310
Tel : +662 725 9000
Publication-No.
161122
Service Manual
A 956001636 00 Electrolux ESE5300PD-VN VNE,IDH
SAFETY WARNING
Always turn off and unplug the machine before detaching any parts.
When servicing machines, do not remove
ANY detachable parts while the machine is powered.
The reason is internal faults may cause shorts to components
that are normally at low voltage presenting a shock hazard.
A 956001637 00 Electrolux ESE5300PD-MY MYH,SGE
A 956001638 00 Electrolux ESE5300PD-TH THE
-2-
SPECIFICATIONS
1.Product informations
Items ESE5300P-VN ESE5300PD-MY ESE5300PD-TH
Rated Voltage/Frequency 220-240V/50Hz 220-240V/50Hz 220-240V/50Hz
Rated current 0.75A 0.75A 0.95A
Rated input power 110W 110W 110W
Defrost power 306W 258W 306W
Climate class T T T
Insulation blowing gas Cyclopentane Cyclopentane Cyclopentane
Lamp LED LED LED
Net
Vol.(Liters)
(ISO 8561)
Refrigerator
320.0 320.0 320.0
Freezer
162.0 162.0 162.0
Total
482.0 482.0 482.0
Dimensions
(Included
packaging)
Width (mm)
980.0 980.0 980.0
Depth (mm)
750.0 750.0 750.0
Height (mm)
1845.0 1845.0 1845.0
Dimensions
(Product
)
Width (mm)
922.0 922.0 922.0
Depth (mm)
676.0 676.0 676.0
Height (mm)
1751.0 1751.0 1751.0
Product weight (KG) (Gross.)
106.0 106.0 106.0
Product weight (KG) (Net.)
94.0 94.0 94.0
Refrigerant
Type R600a R600a R600a
Refrigerant Charge
75g 75g 75g
-3-
SPECIFICATIONS
2.Electrical components
Part Type/Model Technical data
Plug for MYH&SGE Model: 168;Type:
HEC-168 AC250V,13A
Plug for IDH&VNE XYP-02/TC04-10 AC250V,16A
Plug for THE DT Ш-3P-11 AC250V,16A
Door Switch HC-056K Or P29 AC 250V,0.75A ,5E4,T55 Or
AC250V,2.5A ,50E3,T85
Compressor LJ118CY AC220-240V,50Hz,R600a
Defrosting heater
(MYH&SGE) TCRGQ-02 AC 240V,280W
Defrosting heater
(IDH,THE&VNE) RQFS AC 220V,280W
Evaporator Fan motor ZWF-02-2 Or
DLA5985XQEA DC12V , Class 105(A)
Condenser fan motor ZWF-02-2 DC12V ,Class 105(A)
-4-
SPECIFICATIONS
3.Product Dimensions (mm)
4.Interior parts
-5-
SPECIFICATIONS
5.Air flow diagram
Return Air
Return Air
6.Cooling cycle
-6-
SPECIFICATIONS
7.Starting sequence
Remark: Blank box diagram for checking signal of Door in Door function according to
this model not included this mode.
-7-
SPECIFICATIONS
8.Sensor distribute location
No Name Location
Temp. scope of sensors (C°)
Wire break Normal Open
circuit
1 (FS) F-sensor
Left
-
middle side of
F-compartment
Less than
-
50
-50~80
More than
100
2
(R1)
R-sensor
1
Left side of air-
input rim in R
compartment
Less than
-
50
-50~80
More than
100
3
(R2) R
-sensor
2
Right-
middle side
of R compartment
Less than
-
50
-50~80
More than
100
4(DS) Defrost
sensor
Upper
-
right corner
of evaporator
Less than
-
50
-50~80
More than
100
5(RT) Ambient
sensor
Front-top of
cabinet
Less than
-
50
-50~80
More than
100
-8-
SPECIFICATIONS
9.Functions of sensor
No Name Location Functions
1 (FS) F-sensor
Left
-
middle side of
F-compartment
To control temperature of freezer by
compressor
run/stop according to
setting temperature on UI
2
(R1)
R-sensor
1
Left side of air-
input rim in R
compartment
To control temperature of fridge by
damper
open/close according to
setting temperature on UI
3
(R2) R
-sensor
2
Right-
middle side
of R compartment
To control fridge boost activate and
exit automatically base on temperature
changing of fridge compartment. even
if fridge boost is activated by manual
on UI, to exit the function is controlled
by the sensor's
temperature
4(DS) Defrost
sensor
Upper
-
right corner
of evaporator
To control defrost end base on
definitional
temperature of the sensor
5(RT) Ambient
sensor
Front-top of
cabinet
To revise the offset of setting
temperature on UI
automatically base
on different ambient temperature
-9-
PRODUCT INSTALLATION
1.Product installation
1. Allow a minimum of 10mm clearance on both sides.
2. Allow 30mm clearance at the back of the refrigerator.
3. Allow 10mm clearance above the hinge covers.
4. Allow a 349 or 427mm clearance on the hinge side of the
doors, if you place the refrigerator next to the wall. This will make cleaning
easier.
5. Make sure that cupboards or fixtures do not stick out
further than the refrigerator cabinet.
Note: Refrigerator doors on all models are designed to sit
proud of cabinetry (not flush).
2.How to installation?
1. Roll the refrigerator into its final position.
2. The top of the refrigerator should be tilted back by approximately 20mm.
This will allow the doors to self-close providing a consistent door seal and
stability when the doors are open.
3. When you have the appliance in its final position, it needs to be stabilized.
Wind the stability foot down to the floor until it just makes contact with the
floor. Whenever you need to move the appliance, be sure to wind the foot
back up so that the appliance can roll
freely and be sure to reset it when reinstalling. ( The wrench opening size
30mm )
-10 -
4. Check the alignment of the refrigerator to the surrounding cupboards. The top
of the refrigerator should be level from side to side (see diagram below). If you
need to adjust the level, use the adjustable rollers as discussed in Step 3.
5. If the refrigerator now rocks from one corner to the opposite rear corner, this
means that the floor is uneven; you will need to put some packing under one of
the rear rollers. You could use thin pieces of solid material, such as thin board,
vinyl floor tiles or laminate. Place the packing so that it will sit under one of the
rear rollers when the refrigerator is rolled into position.
6. You may now need to fi ne-tune the installation by
repeating Steps 3, 4 and 5.
7. Whenever you need to move the refrigerator, be sure to
wind the foot back up so that the refrigerator can roll freely.
8. Clean your refrigerator thoroughly following the instructions on
page 9 and wipe off any dust that has accumulated during shipping.
9. Plug the refrigerator into the power point. Don’t use a double adaptor. If you
need to roll the refrigerator out to get at the power point, remember to raise the
stability foot before you do so.
10. We recommend that you let your refrigerator run for two to three hours before
you put any food in it. This will allow you to check that it is operating properly.
PRODUCT INSTALLATION
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Electrolux Frigorifero
Electrolux
Electrolux ER1532I Guida rapida
Electrolux
Electrolux TK14014 Manuale utente
Electrolux
Electrolux LNT3LF34W0 Manuale utente
Electrolux
Electrolux EHE6899 Manuale utente
Electrolux
Electrolux IK1345SR Manuale utente
Electrolux
Electrolux IK329SA Manuale utente
Electrolux
Electrolux EN2400AOW Manuale utente
Electrolux
Electrolux Juno JRZ90122 Manuale utente
Electrolux
Electrolux ETE5400 Manuale utente
Electrolux
Electrolux EW23BC87SS4 Manuale utente
Electrolux
Electrolux WRT17MG4BW0 Manuale utente
Electrolux
Electrolux HD-Line 726567 Manuale utente
Electrolux
Electrolux IK2805SZR Manuale utente
Electrolux
Electrolux Icon E23BC78IPSC Manuale utente
Electrolux
Electrolux ERG2305AOW Manuale utente
Electrolux
Electrolux ERB36301X1 Manuale utente
Electrolux
Electrolux EI27BS26JB0 Manuale utente
Electrolux
Electrolux FI23/11NDV Manuale utente
Electrolux
Electrolux ZC24/10F Manuale utente
Electrolux
Electrolux U24089 ERH 3620 X Manuale utente
