Electrolux PLRU1777DS Foglio di istruzioni
Page 1 of 5
HOME PRODUCTS
Model PLRU1777DS ………….. All Refrigerator
Model PLFU1777DS …..……………. All Freezer
Topic:
•Installation guidlines for pair
•Installation guidlines for single
Electrical Information:
•Recommended practice:
ÿPlug unit/units directly into their own properly grounded three prong receptacle*,
protected with a minimum 15 amp time delay fuse or circuit breaker.
ÿDo Not plug unit/units into a Ground Fault Circuit Interrupter (GFCI) circuit.
ÿCord sets are 72” long, and emerge from near the bottom of the unit back. It is
recommended the receptacle be approximately midway between the two units.
*Receptacle, according to Article 100 of the 2005 NEC, is "a contact device installed at
the outlet for the connection of an attachment plug." A typical wall outlet has two
receptacles.
Location:
•The units must be installed on a floor that is level and strong enough to support a fully
loaded refrigerator and freezer.
•Consider water supply availability for models equipped with an automatic ice maker.
•Do Not block toe grille on the lower front of the units. Sufficient air circulation is essential
for the proper operation of the units.
•Do Not install unit/units over HVAC ducts.
Minimum cut-out dimensions for models with Trim Kit:
•Double wide installation: See Fig A
ÿCabinet rough opening – 66” wide x 75” tall
ÿDepth requirement – 25.25”
•All Refrigerator (single unit) installation: See Fig B
ÿCabinet rough opening – 33” wide x 75” tall
ÿDepth requirement – 25.25”
Minimum cut-out dimensions for models without Trim Kit:
•Double wide installation: See Fig C
ÿCabinet rough opening – 65.125” wide x 65.875” tall
ÿDepth requirement – 25.25”
•All Refrigerator (single unit) installation: See Fig D
ÿCabinet rough opening – 32.75” wide x 65.875” tall
ÿDepth requirement – 25.25”
Installation Guidelines
Page 2 of 5
Kitchen Cabinet cut-out dimensions for models with Trim Kit
Tri m
Kit
Kitchen Cabinet cut-out dimensions for models without Trim Kit
KitTrim Kit
Tri m Kit
Fig C
Fig D
Fig B
Fig A
Page 3 of 5
Topic: Installation and Leveling of Stainless Steel All Refrigerator, All Freezer Units with
dynamic condensers (PLKU1777DS & PLRU1777DS):
Electrical Information:
1. Each unit must be plugged into its own dedicated 115 Volt, 60 Hz., AC
circuit.
2. The power cord of each unit is equipped with a three-prong grounding plug
for protection against shock hazards. It must be plugged directly into a
properly grounded three-prong receptacle, protected with a 15 amp time
delay fuse or circuit breaker.
3. Do Not connect units to a Ground Fault Circuit Interrupter (GFCI) circuit.
Location:
1. The units must be installed on a floor that is level and strong enough to
support a fully loaded refrigerator and freezer.
2. Consider water supply availability for models equipped with an automatic ice
maker.
Clearances:
1. Allow the following clearances for ease of installation, proper air circulation,
plumbing and electrical connections.
•Sides -------------- 3/8”
•Top & Back ------ 1”
•Between units ---------- 3/16”
2. Do Not block toe grille on the lower front of the units. Sufficient air
circulation is essential for the proper operation of the units.
Wood Base Removal:
1. Remove two leveling legs provided in literature bag. While unit is lying on its
back, remove four 3/8” hex crating bolts from wood base. Remove and
discard wood base.
2. Install both leveling legs in rear of unit and loosen front leveling legs if
necessary. See Fig. A
Page 4 of 5
Leveling Instructions for Refrigerator and Freezer:
1. Leveling leg adjustments may require a 1-1/4” wrench.
2. Level door of the refrigerator using all four levelers and slide unit into place.
Recheck for levelness and adjust if necessary.
3. Measure distance from floor to bottom of door on the refrigerator. Adjust
and level the freezer so door height matches.
4. Leveling Leg Adjustments: See Fig. B
•One full turn of all four leveling legs will raise door 5/32”.
•One full turn of both front leveling legs will raise door 3/16” and tilt top
of door back 7/16”.
•One full turn of both rear leveling legs will lower door 1/32” and tilt top
of door forward 7/16”.
•One full turn of both side leveling legs will raise door 3/16” and tilt top
of door 3/8”.
5. Slide the freezer into place leaving a minimum gap of 3/16” between units
for door swing clearance.
6. This last step may require at least one unit to be taken out of location to
properly align units in a built-in application.
7. Properly aligned units should have level doors which are flush and parallel.
See Fig. C
Page 5 of 5
Raises Door
Loosen Front
Leg Levelers
Unit Lying on its Back
Install Rear
Leg Levelers
Remove Wood Base
Fig. A
Fig. B
Remove Four
Crating Bolts
3/16” Min.
65-1/4” Min.
64-3/16” Min.
Doors
Flush
Doors
Parallel
Fig. C
Freezer
Refrigerator
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Electrolux Frigorifero
Electrolux
Electrolux REFRIGERATION Manuale utente
Electrolux
Electrolux ERU 13300 Manuale utente
Electrolux
Electrolux CS370 Manuale del proprietario
Electrolux
Electrolux ERN29550 Manuale utente
Electrolux
Electrolux ETB2302J-A Manuale utente
Electrolux
Electrolux TK 137 Manuale utente
Electrolux
Electrolux ER 8625 D Manuale utente
Electrolux
Electrolux EQAXF01BXWP Manuale utente
Electrolux
Electrolux IK2671BNR Manuale utente
Electrolux
Electrolux ERB 3021 Guida rapida
Electrolux
Electrolux ERO 2920 Guida rapida
Electrolux
Electrolux LXB1AE13W0 Manuale utente
Electrolux
Electrolux FRT18G6JB7 Manuale utente
Electrolux
Electrolux IK1695Z Manuale utente
Electrolux
Electrolux ER 7549B Guida rapida
Electrolux
Electrolux ER 1380 U Manuale utente
Electrolux
Electrolux ERB3222 Manuale utente
Electrolux
Electrolux ER 2341B Manuale di installazione e funzionamento
Electrolux
Electrolux 730191 Manuale utente
Electrolux
Electrolux ER7826/1B Manuale utente
