ELEKTRA DIGI2 Manuale utente
DIGI2
DIGI2p
www.elektra.eu
electronic
temperature controller
Instrukcja montażu PL
Installation manual UK
The ELEKTRA DIGI2 (DIGI2P) has been designed to offer
you both comfort and energy savings. It allows you to
programme and adjust the heating or air conditioning to
3 temperature levels.
Comfort Temperature: this is the temperature for the hours that the
(room/home) is occupied.
Reduced Temperature: this is the temperature when the (room/home) is less
occupied or perhaps at night.
Frost Protection Temperature: this is the minimum temperature for long
periods of non-occupation. This protects the (room/home) from freezing.
These 3 pre-recorded programmes, and an additional blank programme, allow you
to adapt your heating each day to suit your lifestyle.
This manual/leaflet introduces you to the different functions of this temperature
controller.
2
DIGI2/DIGI2p
CONTENTS
1. Installing or re-installing the batteries
2. Setting current time and day
3. Temperature setting
4. Programming
5. Programme reading
6. "Auto" automatic mode
7. "Manu" manual mode
8. Temporary temperature modification
9. Prolonged absence mode (Holiday)
10. Installation maintenance signal
11. Control by telephone (DIGI2)
12. Installers guide
13. Technical data
3
4
Attention: Before you start programming, first connect the floor sensor (DIGI2p)
DIGI2/DIGI2p
1. INSTALLING OR RE-INSTALLING THE BATTERIES
ELEKTRA DIGI2 (DIGI2p) is equipped with a warning light to indicate when the
batteries need replacing. As soon as this indicator lights up at the bottom right-
hand side of the display panel, replace the batteries (use two 1.5V AA R6 alkaline
batteries - life is approximately 18 months): The device remains programmed for 60
seconds while batteries are being replaced.
Before beginning the programming of the device, please
slide cover down and press RES with the tip of a pen.
5
2. SETTING CURRENT TIME AND DAY
When you change the time or the day.
You are putting the device into operation
for the first time or
You have just pressed the RES button (see above).
12:00 appears and the pointer flashes under day 1.
a) Set the time using the +/–buttons (the numbers run off more quickly when the
button is pressed continuously).
b) Set the current day by pressing several times on the 1-7 button. A pointer
appears under the corresponding day (1=Monday, 2=Tuesday,
3=Wednesday, etc.).
6
DIGI2/DIGI2p
c) Validate with the OK button
d) If you wish to change the time or the day, press the MODE button until the
pointer appears under the clock sign and continue as above for points a, b
and c.
7
a
bc
d
8
a
b
c
DIGI2/DIGI2p
3. TEMPERATURE SETTING
Comfort and reduced temperatures are pre-set:
Comfort = + 20°C
Reduced = + 16°C.
Modification of comfort temperature
a) Press the comfort button
b) Modify the temperature with the +/–buttons
c) Validate with OK
Modification of reduced temperature
a) Press the reduced button
b) Modify the temperature with the +/–buttons
c) Validate with OK
9
4. PROGRAMMING
You can programme your week according to 4 programme settings:
P1, P2, P3 are pre-recorded and cannot be modified.
P4 is blank and allows you to create a personalized programme varying according
to the day of the week.
P1 = Comfort temperature from 6 a.m. till 11 p.m.
Reduced temperature from 11 p.m. till 6 a.m.
The standard allocation of P1 is to 7 days of the week. If this corresponds
to your life style, stay in automatic mode. Otherwise, continue.
10
DIGI2/DIGI2p
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali ELEKTRA Regolatori di temperatura
