Elettrotest RPS Manuale utente

Elettrotest S.p.A. P.zza R. Riello, 20/B - 45021 Badia Polesine ( RO ) - tel. +39 0425 53567 - Fax +39 0425 53568

e-mail: info@elettrotestspa.it http: www.elettrotestspa.it

62000582 Rel.1.0 –15/03/2018

RPS/M/1K

USER MANUAL

MANUALE UTENTE

USER MANUAL RPS/M/1K

Elettrotest S.p.A. P.zza R. Riello, 20/B - 45021 Badia Polesine ( RO ) - tel. +39 0425 53567 - Fax +39 0425 53568

e-mail: info@elettrotestspa.it http: www.elettrotestspa.it

62000582 Rel.1.0 –15/03/2018

1. RACK POWER SUPPLY……………………………………………………………………………………………....2

1.1. GENERALITY……………………………………………………………………………………………………...2

1.1.1. INTRODUCTION……………………………………………………………………………………....2

1.1.2. SAFETY WARNINGS…………………………………………………...………………………..…..2

1.1.3. RISK TYPOLOGY……………………………………………………………………………………....3

1.2. VOLTAGE OUTPUT………………………………………………………….......……………………………3

1.3. FREQUENCY OUTPUT……………………………………………………….……..............................4

1.4. USER INTERFACE……………………………………………………………………..............................4

1.5. MODELS……………………………………………………………………………..…...............................4

1.6. GENERAL PERFORMANCES………………………………………………………..………………………5

1.7. GENERAL SPECIFICATIONS…………………………………………………………………………………5

1.8. MAXIMUM OUTPUT CURRENT…………………………………………………….........................5

1.9. NOTES FOR THE INSTALLATION………………………………………………………………………….6

1.9.1. RPS/M/1K………………………………………………………………………………………………..6

2. NOTES FOR USERS…………………………………………………………………………………………………….8

2.1. SWITCHING ON…………………………………………………………………........……………………….8

2.2. VOLTAGE FEEDBACK………………………………………………………………………………………….8

2.3. LIMITATION CURRENT MODE…………………………………………………...……………………….9

2.3.1. LIMITATION SETTING……………………………………………………………………………..10

2.3.2. RPS1000…………………………………………………………………………………………………11

2.4. OUTPUT RELAY………………………………………………………………...……............................11

2.5. ALARMS……………………………………………………………………………...…………………………..12

2.5.1. SUPPLY ALARMS…………………………………………………………..….........................12

2.5.2. SYSTEM ALARMS………………………………………………………..………………………….12

2.5.3. CURRENT ALARM……………………………………………………...…………………………..12

2.5.4. VOLTAGE ALARM……………………………………………………...…..……………………...13

3. SERIAL REMOTE CONTROL...…………………………………………………...……………………………..13

3.1. CONTROL SOFTWARE ……………………………………………………...……………………………..13

3.2. SERIAL CABLE……………………………………………………………...…………………………………..13

4. ANALOG REMOTE CONTROL………………………………………………...………………………………..14

4.1. ANALOG INTERFACE……………………………………………………………....……………………….14

4.2. PERFORMANCES…………………………………………………………………….............................15

5. POWER SUPPLY CONNECTION…………………..……………………………………..........................16

5.1. FUSES……………………………………………………………………………….…...............................16

5.2. RCD PROTECTION…………………………………………………………………………………………….16

5.3. MAGNETO THERMAL PROTECTION………………………………………………………………….16

5.4. WIRING DIAGRAM………………………………………………………………..…..........................17

6. MECHANICAL DRAWING……………………………………………………………….............................18

USER MANUAL RPS/M/1K

Elettrotest S.p.A. P.zza R. Riello, 20/B - 45021 Badia Polesine ( RO ) - tel. +39 0425 53567 - Fax +39 0425 53568

e-mail: info@elettrotestspa.it http: www.elettrotestspa.it

62000582 Rel.1.0 –15/03/2018

1. RACK POWER SUPPLY

1.1. GENERALITY

1.1.1. INTRODUCTION

RPS is a power source that supplies a sinusoidal and stable voltage. Its output voltage is adjustable

in frequency and amplitude.

1.1.2. SAFETY WARNINGS

The manufacturer urges users to read the user’s manual for our products carefully before

installation.

The installation must be carried out by qualified technical staff. The non-observance of the

warnings in this manual can cause electric shocks, even fatal ones.

Please find below some general safety warnings.

V GENERAL WARNINGS

This equipment must be connected to the mains supply using the appropriate safety

devices. Please consult the relevant paragraph 5, in this manual.

RPS must be connected to safety ground through the apposite connections. The non-

observance or the degradation of this earth connection can lead to electric shocks, even fatal

ones. As regards the correct connection modes, please refer to the information contained in

paragraph 5.

Disconnect RPS from the mains before any work on the equipment and on the connected

power loads.

Before touching the load or the output connector make sure that the power supply on the

device has been disconnected for at least 5 minutes. This is the time necessary in order for the

capacitors inside the device to discharge. The non-observance of this discharge time can lead

to electric shocks, even fatal ones.

The output of RPS is not isolated respect to the main power supply and so NONE OF THE

TWO OUTPUT PHASES CAN BE CONNECTED TO THE GROUND.

Avoid heavy shocks to the equipment (especially during transport) or exposure to extreme

weather conditions.

Any damage to the product due to transportation, incorrect installation or improper use is

not covered by the guarantee supplied by the manufacturer.

Do not use the equipment in explosive environments or in the presence of dust, acids or

corrosive and/or inflammable gases.

Tampering with or dismantling any component in the equipment will cause the automatic

expiry of the guarantee.

USER MANUAL RPS/M/1K

Elettrotest S.p.A. P.zza R. Riello, 20/B - 45021 Badia Polesine ( RO ) - tel. +39 0425 53567 - Fax +39 0425 53568

e-mail: info@elettrotestspa.it http: www.elettrotestspa.it

62000582 Rel.1.0 –15/03/2018

Do not operate or store under conditions where condensing may occur or where

conductive debris may enter in the case.

The manufacturer declines all responsibility for damage to people or things

caused by an improper use of its products.

1.1.3. RISK TYPOLOGY

ELECTRIC RISK

There are dangerous voltages inside RPS and over the output connector.

The non-observance of the warnings suggest in this manual can lead to electric shocks, even

fatal ones.

OVERHEATING RISK

In the case of a ventilation system failure, the metal parts of the inverter may reach high

temperatures (in some cases greater than 70°C).

1.2. VOLTAGE OUTPUT

The output voltage is guaranteed perfectly sinusoidal, with a distortion of less than 0.3%

regardless of the load. The value of output voltage is kept perfectly stable within 0.1% regardless

of the load.

RPS is also able to compensate for possible voltage drops on the output wires, ensuring in this way

the exact voltage you want on the load.

The load that RPS is able to drive can vary from the pure capacity to the pure inductance, but also

up to non symmetrical current loads, as for instance a single half wave rectifier.

The output voltage is adjustable with continuity from zero to full scale. Furthermore RPS is capable

to keep the voltage stable also with time variable loads, as for example the pulsating loads. In fact

RPS recovers the distortion of the waveform within 0.3% and the amplitude of the voltage within

0.1% in less than half period.

USER MANUAL RPS/M/1K

Elettrotest S.p.A. P.zza R. Riello, 20/B - 45021 Badia Polesine ( RO ) - tel. +39 0425 53567 - Fax +39 0425 53568

e-mail: info@elettrotestspa.it http: www.elettrotestspa.it

62000582 Rel.1.0 –15/03/2018

Furthermore, RPS can bear a short-circuit for an indefinite time without suffering any

consequence.

ATTENTION !!!!

THE OUTPUT OF RPS IS NOT ISOLATED RESPECT TO THE MAIN POWER SUPPLY

NONE OF THE TWO OUTPUT PHASES CAN BE CONNECTED TO THE GROUND

1.3. FREQUENCY OUTPUT

RPS allows the regulation of the output frequency from 10 Hz to 80 Hz. The output frequency can

be adjusted with continuity into the regulation range and it has a stability of 0.01% regards to set

frequency.

1.4. USER INTERFACE

RPS can be controlled only through copyrighted serial communication protocol.

RPS allows various usage selections: wires drop compensation, working frequency, output DC,

output AC.

RPS gives the user clear information on the status of the output.

It is monitored both the set voltage and the set frequency. The output voltage can be remotely

read with a precision of 0.3%.

The user is also warned in case of overcurrent obtainable by the RPS, or in case of high loss on the

wires, that should not exceed 5% of the set voltage.

1.5. MODELS

The models are different depending on the rated power and the supply mode (single phase or

three phase with neutral).

MODELS

NOMINAL

POWER

SUPPLY

VOLTAGE

WEIGHT

INPUT

CURRENT

DIMENSIONS

A, L, P mm

RPS/M/1K

1.000VA

230Vac ±10%

1PH

12 kg

8.5A

2U : 84 TE : 440

USER MANUAL RPS/M/1K

Elettrotest S.p.A. P.zza R. Riello, 20/B - 45021 Badia Polesine ( RO ) - tel. +39 0425 53567 - Fax +39 0425 53568

e-mail: info@elettrotestspa.it http: www.elettrotestspa.it

62000582 Rel.1.0 –15/03/2018

1.6. GENERAL PERFORMANCES

All the following features are valid in the normal operation mode. They are not valid during the

output current limitation.

1.7. GENERAL SPECIFICATIONS

PARAMETER

VALUE

Output frequency range

DC/ 10Hz - 80Hz

Frequency resolution

0.02Hz

Frequency precision and time stability

100ppm

Output voltage at constant power

300V

Output voltage resolution

0.025% f.s. (12 bit su f.s.)

Operating temperature of function

0°C - 35°C

1.8. MAXIMUM OUTPUT CURRENT

PARAMETER

VALUE

Distortion of the output waveform

<0.3%

Stability of the output voltage

<0.1%

Accuracy of the output voltage

<0.5%

Recovery time of the output waveform

<10ms

Recovery-time of the output voltage

<10ms

Maximum compensated drop on wires

5% f.s.

Recovery-time of drop on wires

<200ms.

RPS/M/1K

REGIME CONTINUO/CONTINUOUS OPERATION

CORRENTE MASSIMA\MAX CURRENT

POTENZA MASSIMA\MAX POWER

PORT

50 Hz

60 Hz

LOAD

PORT

50 Hz

60 Hz

LOAD

300

2,7 A

2,6 A

CAP.

300

811 VA

768 VA

CAP.

300

4,1 A

4,3 A

IND.

300

1235 VA

1277 VA

IND.

300

3,4 A

3,3 A

RES.

300

1020 VA

1001 VA

991 VA

RES.

REGIME IMPULSIVO (MAX 3 SECONDI)/ IMPULSIVE OPERATION(MAX 3 SECONDS)

CORRENTE MASSIMA\MAX CURRENT

POTENZA MASSIMA\MAX POWER

PORT

50 Hz

60 Hz

LOAD

PORT

50 Hz

60 Hz

LOAD

300

6,2 A

6,1 A

CAP.

300

1862 VA

1820 VA

CAP.

300

7,6 A

7,8 A

IND.

300

1235 VA

2329 VA

IND.

300

6,9 A

RES.

300

2064 VA

2059 VA

RES.

USER MANUAL RPS/M/1K

Elettrotest S.p.A. P.zza R. Riello, 20/B - 45021 Badia Polesine ( RO ) - tel. +39 0425 53567 - Fax +39 0425 53568

e-mail: info@elettrotestspa.it http: www.elettrotestspa.it

62000582 Rel.1.0 –15/03/2018

1.9. NOTES FOR THE INSTALLATION

1.9.1. RPS/M/1K

Connect one supplying cable 2P+G (standard IEC cable) of suitable section (minimum

section 3x1.5 mm2).

Protect the input line with the circuit breakers presented in paragraph 5.

Connect load cable to the output connector. Use an appropriate sections according to the

maximum load tolerable by the RPS.

Put the ferrite core on the load cable close to RPS.

Optionally: Connect the sense wires.

Keep front area free for ventilation.

When RPS is mounted inside a cabinet you must install a forced ventilation in order to

expel the hot air.

Never lay power cables (including the electrical cables) and probe signal cables in the same

conduits;

Cleaning the device: When cleaning the device do not use ethyl alcohol, hydrocarbons

(petrol), water, detergents, ammonia and derivatives. Use only a dry cloth.

INPUT CONNECTOR

OUTPUT CONNECTOR

FERRITE CORE

USER MANUAL RPS/M/1K

Elettrotest S.p.A. P.zza R. Riello, 20/B - 45021 Badia Polesine ( RO ) - tel. +39 0425 53567 - Fax +39 0425 53568

e-mail: info@elettrotestspa.it http: www.elettrotestspa.it

62000582 Rel.1.0 –15/03/2018

INDEX

DESCRIPTION

Serial 9 poles connector

Power output connector

Fan grid

Power input connector

Earth connector

Analog port

Ventilation Grill

RPS/M /1K

USER MANUAL RPS/M/1K

Elettrotest S.p.A. P.zza R. Riello, 20/B - 45021 Badia Polesine ( RO ) - tel. +39 0425 53567 - Fax +39 0425 53568

e-mail: info@elettrotestspa.it http: www.elettrotestspa.it

62000582 Rel.1.0 –15/03/2018

2. NOTES FOR USERS

2.1. SWITCHING ON

RPS doesn't have power switch and so when the input connector is powered, RPS turns on. RPS

needs (after power on) less than 10 seconds to be ready.

2.2. VOLTAGE FEEDBACK

The output voltage stabilization works the same in both the configurations on the RPS output

terminals (2 wire) and on a possible long distance outlet (4 wire), to compensate the voltage drop

due to cable connections. To work in 4WIRES configuration, you must perform the wiring as shown

in the figure below and set "4WIRE" mode via remote control.

RPS compensates the voltage drop on the connections up to 5% of the set voltage.

To prevent any overheating of the line, when the limit has been exceeded, RPS does not guarantee

that the value of output voltage is equal to the voltage set. In this case it displays an error signal

(see the paragraph VOLTAGE ALARMS).

USER MANUAL RPS/M/1K

Elettrotest S.p.A. P.zza R. Riello, 20/B - 45021 Badia Polesine ( RO ) - tel. +39 0425 53567 - Fax +39 0425 53568

e-mail: info@elettrotestspa.it http: www.elettrotestspa.it

62000582 Rel.1.0 –15/03/2018

2.3. LIMITATION CURRENT MODE

With RPS we can set two limitation current mode:

PEAK LIMITATION MODE: Output current is limited instantaneously without delay at the

limitation set. Remain only an initial transient peak due to the output capacitor discharge.

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Elettrotest Generatore portatile

Elettrotest

Elettrotest RPS/M/1K Manuale utente

Elettrotest

Elettrotest CPS Manuale utente

Manuali Generatore portatile popolari di altre marche

Kohler

Kohler 20EORZ Manuale di istruzioni

Powerhorse

Powerhorse 83171 Manuale utente

HURST

HURST ML-630-SI Manuale utente

ETQ

ETQ TG4000 Manuale utente

Briggs & Stratton

Briggs & Stratton 40265 Guida all'installazione

ConMed

ConMed 7550 Manuale utente

Owon

Owon Waveform Generator Manuale utente

evertz

evertz 7700 Series Manuale utente

Power Stroke

Power Stroke PS906025 Manuale utente

Firefly

Firefly Cygnus CYG2400/460/24 Manuale utente

Draper

Draper PG950S Aggiornamento firmware

PowerBoss

PowerBoss PowerBoss Manuale utente

SDMO

SDMO SH 4000 Manuale utente

EINHELL

EINHELL STE 5500 Manuale utente

Wanco

Wanco WI3000P Manuale utente

Full Boar

Full Boar FBT-3300 Manuale utente

Dwyer Instruments

Dwyer Instruments ASG Manuale utente

Westinghouse

Westinghouse WH1000i Series Manuale utente