Elexa DOME DMOF1 Manuale utente
Always Connected. Always Covered.
On/Off Plug-In Switch
User Manual
DMOF1
Page 2
On/Off Plug-In Switch Advanced User Manual
Preface
As this is the full User Manual, a working knowledge of Z-Wave automation
terminology and concepts will be assumed. If you are a basic user, please visit
www.domeha.com for instructions. This manual will provide in-depth technical
information about the On/Off Plug-In Switch, especially in regards to its compli-
ance to the Z-Wave standard (such as compatible Command Classes, Associa-
tion Group capabilities, special features, and other information) that will help
you maximize the utility of this product in your system.
Preface
Page 3
On/Off Plug-In Switch Advanced User Manual
Table of Contents
Table of Contents
Preface................................................................................................................................. 2
Description & Features..................................................................................................... 4
Specifications..................................................................................................................... 5
Physical Characteristics ................................................................................................... 6
Inclusion & Exclusion........................................................................................................ 7
Factory Reset & Misc. Functions..................................................................................... 8
Physical Installation.......................................................................................................... 9
LED Behavior .................................................................................................................... 10
Button Behavior............................................................................................................... 11
Compatible Command Classes..................................................................................... 12
“Configuration” Command Class Parameters ............................................................ 16
Troubleshooting.............................................................................................................. 19
Warranty & Support ........................................................................................................ 20
Page 4
On/Off Plug-In Switch Advanced User Manual
Description & Features
The Dome On/Off Plug-In Switch is a Z-Wave Plus device that plugs into a
standard 3-prong power outlet and lets you turn on or off any connected elec-
tronic device. The On/Off Plug-In Switch also monitors how much energy the
attached device uses, and reports the data to your Z-Wave Hub.
Key Features:
» Z-Wave Plus Certified
» Turns on or off any plugged-in device
» Extends the range of your Z-Wave system
» Up to 150’ wireless range, depending on environment
» Small size - won’t block the adjacent outlet!
» Fits any standard 3-prong American power outlet
» Reports energy consumption data
» Overload protection
» Max current - 13 A
*Event-based response requires use of external sensors and compatible controller
SolidWorks Student Edition.
For Academic Use Only.
Description & Features
Page 5
On/Off Plug-In Switch Advanced User Manual
Specications
Package Contents:
Technical Specications
Radio protocol Z-Wave Plus (500 series)
Power supply 110-230V AC 50/60Hz
Max Current 13A
Power Consumption 0.13W
Radio frequency 908.4 MHz US
Z-Wave Range Up to 150’ depending on environment
Dimensions (L x W x H) 1.8” x 1.8” x 1.8”
Table 1 - Technical Specications
USER MANUAL On/Off Plug-In Switch
Thank you for purchasing the DOME
On/Off Plug-In Switch, which works with your
Z-Wave Certied Controller to turn on and off
any plugged in electronic device and monitor its
power consumption.
SolidWorks Student Edition.
For Academic Use Only.
Connect Button
DEVICE PORT
PLUG
Including/Connecting into the Z-Wave Network:
Follow the instructions for your Z-Wave certied Controller
to enter inclusion mode.
When prompted by the Controller:
1. For proper inclusion, bring the On/Off Plug-In Switch
to within 10 feet of your Controller and plug it in. After
inclusion, the device can be moved to any desired
location.
2. Press the Connect Button quickly 3 times in a row.
The LED Indicator will ash ve times indicating inclusion.
Excluding/Disconnecting from the Z-Wave Network:
Follow the instructions for your Z-Wave certied Controller to
enter exclusion mode.When prompted by the Controller:
1. Plug in the On/Off Plug-In Switch within range of your
Z-Wave Controller.
2. Press the Connect Button quickly 3 times in a row.
The LED Indicator will ash ve times indicating exclusion/dis-
connection.
Resetting the On/Off Plug-In Switch to Factory Default
Settings:
To disconnect from the Z-Wave Network and restore factory default
settings:
1. Plug in the On/Off Plug-In Switch.
2. Hold the Connect Button for 10 seconds until the LED Indicator
blinks once, then release the button.
Only do this if the controller is disconnected or otherwise unreach-
able!
Overload Protection:
The On/Off Plug-In Switch shuts off power and the LED Indicator
will turn red when a current higher than 13 Amps passes through.
To restore power after a current overload, power cycle the plug
either by pressing the physical button or through your Z-Wave
controller. You can also reboot the plug by unplugging it from the
outlet.
On/Off Plug-In Switch
SolidWorks Student Edition.
For Academic Use Only.
Specications
Page 6
On/Off Plug-In Switch Advanced User Manual
Physical Characteristics
The names used in Figures 1 & 2 will be used throughout this manual. Please
refer to this page as needed.
SolidWorks Student Edition.
For Academic Use Only.
BUTTON
DEVICE PORT
PLUG
Figure 1 - On/Off Plug-In Switch Parts
SolidWorks Student Edition.
For Academic Use Only.
DMOF1
Figure 2 - Bottom View
Physical Characteristics
Page 7
On/Off Plug-In Switch Advanced User Manual
Inclusion & Exclusion
Inclusion
Follow the instructions for your Z-Wave Certified Conto enter inclusion mode.
When prompted by the controller:
1. Plug the On/Off Plug-In Switch into an outlet 10’ from your controller. You
can bring it to your desired location after the inclusion process.
2. When prompted by the controller, quickly press the BUTTON 3 times.
3. A yellow LED will flash five times indicating inclusion.
Exclusion
Follow the instructions for your Z-Wave Certified Conto enter exclusion mode.
When prompted by the controller:
1. Plug the On/Off Plug-In Switch into an outlet 10’ from your controller.
2. Press the BUTTON quickly 3 times in a row.
3. A yellow LED will flash five times indicating exclusion/disconnection.
Inclusion & Exclusion
Page 8
On/Off Plug-In Switch Advanced User Manual
Factory Reset & Misc. Functions
Resetting the On/Off Plug-In Switch
If needed, the On/Off Plug-In Switch can be reset locally by following these
steps. Only do this when your Z-Wave controller is disconnected or otherwise
unreachable. Beware that resetting your device will disconnect it from the sys-
tem:
1. Confirm that your On/Off Plug-In Switch is powered up.
2. Press and hold the BUTTON for at least 10 seconds then release. The LED
will blink once in a red color followed by 5 times in a pink color indicating
a successful factory reset.
3. The On/Off Plug-In Switch’s memory will be erased to factory settings.
Factory Reset & Misc. Functions
Page 9
On/Off Plug-In Switch Advanced User Manual
Physical Installation
The On/Off Plug-In Switch can be installed in any standard 3-prong American
power outlet. To control or monitor an electronic device, simply plug it into the
DEVICE PORT. Make sure there is sufficient Z-Wave coverage in your desired
installation location.
Physical Installation
Page 10
On/Off Plug-In Switch Advanced User Manual
LED Behavior
Color Behavior This happens when…
Pink
Blink 5 times in 1 second …the device powers on, but is not yet included in a
Z-Wave Network.
Blink 5 times in 500ms
…the BUTTON is pushed 3 times after the
On/Off Plug-In Switch is already in a Z-Wave net-
work, and the device sends a notication with its
Node Info.
Blue Blink 5 times in 300ms …the device powers on, and is arleady included in
a Z-wave network.
Yellow
Blink 5 times in 500ms …the BUTTON is pushed three times, including the
On/Off Plug-In Switch into a Z-Wave network.
Always On …the current is above the limit set in Param 4 (12A
by default.)
Red
Blink Once
…the BUTTON is pressed for an extended period of
time, resetting the On/Off Plug-In Switch to factory
default settings.
Blink Once a Second
…the current is above the limit set in Param 3 (13A
by default.) Power will be shut off; LED and power
will return to normal when the current drops below
the level set in Param 3 and the BUTTON is pushed
once.
Green Always On …the On/Off Plug-In Switch is powered on.
Table 2 - LED Blinking Behavior
LED Behavior
Indice
