Elite Screens Vmax Series Manuale utente

092514-JA www.elitescreens.com 1

VMAX Dual Series

Dual Format Electric Projection Screen

User’s Guide

Important Safety and Warning Precautions

Make sure to read this user’s guide and follow the procedures below.

Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black Top

Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens. Unapproved changes or

modifications (except for cutting the power cord for hardwire installations) to this unit are prohibited and will void

your warranty. For more information, please contact our Technical Support Dept. at (877) 511-1211 Ext. 604.

Please retain this user’s guide for future reference.

To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the

manufacturer.

Handle the unit carefully during transportation to avoid any damages.

To ensure safe and reliable operation, direct connection to a properly grounded power source is

advised.

The power outlet supplying power to the unit should be close to the unit and easily accessible.

Do not install the unit on uneven or inclined surfaces.

Do not put heavy objects on the power cord and position it properly to avoid creating a trip

obstacle.

Never overload the power cord to prevent an electric shock or fire due to a loose contact or a short

circuit.

There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by yourself.

No one except authorized technicians can open and make repairs to this unit.

Make sure the power source this unit is connected to has a continuous power flow.

If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to

avoid overheat.

Do not handle the power plug when your hands are wet or your feet are in contact with water.

Do not use this unit under the following circumstances.

Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.

Avoid direct Sunshine, rain shower and moisture.

Keep away from fire sources and high temperature to prevent this device from overheating.

Cut off the power supply first before transportation or maintenance.

Fully disconnect from the power supply when the unit is not in use for a long period of time, as

should be done with any other electric household appliance.

To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is

obvious damage or if there are any evident broken parts.

092514-JA www.elitescreens.com 2

Pre-Installation

1. Carefully unpack the screen.

2. Always handle the screen in a leveled position on a clean surface.

3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign

particles such as dust, sawdust, and/or liquids.

Installation Warning

Due to various installation environments, the instructions provided in this user’s guide are for reference

only. Please consult a professional installation company for further installation and safety advice. The

installer must insure that proper mounting hardware is used to provide adequate strength suitable for the

installation. Elite Screens is not liable for any faulty installations.

Individual modifications to this product are prohibited and will void the warranty with the manufacturer. Please

contact Elite Screens Customer Service for any questions.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur on a particular installation. If this

equipment causes harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures.

Reorient or relocate the receiving antenna of the device which may be casing the interference.

Increase the separation between the screen and the device’s receiver.

Connect the equipment into a different power outlet other than the device.

Note

Regardless of the mounting method, the screen should be securely supported so that the vibration or

pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure

that the fasteners used are of adequate strength and suitable for the installation location.

Hardware Parts List for the VMAX Dual Series

Please make sure all of the following items are included before proceeding with installation.

A. Hollow Wall Anchor x 6 pcs

B. Screw x 6 pcs

C. R18mmx6mm Washer x 6 pcs

D. M6x12mmx1.5mm washer,

M6x24mm screw, M6 nut x 4 pcs

F. Black Tape x 2 pcs

092514-JA www.elitescreens.com 3

Weight Bar Notice and Black Tape

The VMAX Dual’s weight bars have been secured to hold in place with a metal plate which is screwed on.

Please remove the metal plate prior to operating the screen. The screen will not deploy while the metal

plate is in place. Failure to remove the metal plate will result in possibly damaging the motor.

Weight bar metal plate removal

1. Unscrew both screws from the concave metal plate and remove it from the weight bars.

Black Tape

2. Stick a strip of black tape (F) over the two screw holes under the weight bar to cover them.

The screw holes under

the weight bars.

Concave metal plate

F. Black Tape

092514-JA www.elitescreens.com 4

Installation

The VMAX Dual Series screen is designed for installation on a wall or ceiling. All hardware is included to

allow a wall installation. A professional installer is strongly recommended for safety purposes.

A. Wall Installation

1. Measure the length distance (L)

between each hole on the screen’s end

flange as shown in the image above.

2. Measure and mark the

required height for your

installation. Next, drill three

holes vertically 37mm apart for

the 6 inch wall brackets (E).

Then, drill another hole

according to the measurement

distance obtained from Step 1.

Finally, drill the remaining two

holes for the wall bracket.

3. Insert the hollow wall

Anchors (A) into the drilled

holes. Align the 6 inch wall

brackets (E) to the drilled

holes and secure with the

screws (B).

4. After securing the 6 inch wall

brackets (E)to the wall, bring the

screen over the top of the brackets.

5. Align the screw holes from

the screen’s end flanges to the

wall brackets top opening.

6. Insert the M6x24mm screw

& washer and secure with the

M6 nut (D).

B. Ceiling Installation

1. Measure the (L) and (W) distance and mark the area on your ceiling. Those measurements are the holes

located at the end flanges of the VMAX Dual screen as shown in the drawing.

WALL

Woodscrew and

R18mmx6mm

washer

37mm

Two or more people are

required to lift screen up.

092514-JA www.elitescreens.com 5

2. Drill four holes in the ceiling and insert the hollow wall anchors (A) in each of the drilled holes.

Two or more people are required for the next steps

3. Carefully bring up the screen and align the end flange holes of the screen with the two drilled holes in the

ceiling.

4. Insert the screw (B) in the hollow wall anchor (A) and fasten with a screw (B) to secure the screen in

place. Repeat procedure until screen is safely installed.

C. Suspended (Optional Ceiling Installation)

The following list of hardware is not included with the VMAX Dual. These are general hardware parts

required for installing the VMAX Dual on a high ceiling.

F. Threaded Screw Rod x 4

G. Expansion anchor x 4

H. Washer x 12

I. Nut x 12

1. Measure the (L) and (W) distance and mark the area on your ceiling. Those measurements are the holes

located at the end flanges of the VMAX Dual screen as shown in the drawing.

Hollow Wall

Anchor

Align the

holes

Screw (B) is inserted

into hollow anchor (A).

092514-JA www.elitescreens.com 6

2. Insert the nuts (I) and washers (H) into every threaded screw rod (F) as shown on Fig 1.

3. Next, insert the expansion anchors (G) in the four drilled holes and put the threaded screw rod in the

expansion anchors (Fig 2).

4. Then fasten the nuts (I) to secure the position of the threaded screw rod (Fig.3).

5. Lastly, align the end flange holes to the threaded support rods and fasten them with the nuts and washers

as show below.

Accessories for the VMAX Dual Series

RF remote x 1

5-12V trigger cable x 1

Bubble leveler

AAA batteries x 2

Fig.1

Fig.2

Fig.3

092514-JA www.elitescreens.com 7

Control System and Screen Operation

The VMAX Dual series screen’s main unique feature is the ability of changing the screen’s ratio to

2.35:1and 16:9 with the push of a button with the RF remote (Radio Frequency). This is accomplished by

the screen’s dual screen materials and motors.

1. Radio Frequency Remote Operation

Press the 2.35:1 button on the RF remote so the screen can lower and display a 2.35:1 format.

Press the 16:9 button on the RF remote, this will retract the 2.35:1 screen into the housing. When the 2.35:1

screen has stopped, the 16:9 screen commences its deployment.

2.35:1

16:9

2.35:1

2.35:1 screen

retracts

16:9 screen

deploys

092514-JA www.elitescreens.com 8

Press “UP” button on the RF remote to retract the screen into the housing.

2. Wireless 5-12 volt trigger operation

The VMAX Dual may be controlled through a projector’s 5-12 volt trigger through the Radio Frequency

remote control. It will synchronize with the projector’s power cycle and deploy the16:9 screen when the

projector is turned on and retract it when the projector is powered off.

Plug the 5-12 volt trigger cable as shown below and turn on your projector.

If the 16:9 screen does not deploy, try the following steps to reprogram the RF remote to your VMAX Dual.

Step1: Make sure to unplug your screen from the power outlet

Step2: Hold the UP button on your RF remote

Step3: While holding the UP button, plug the screen back to the power outlet

Step 4: Wait 5 seconds and then release the UP button

Step 5: The RF remote should now be programmed with your screen and ready to synchronize with your projector’s

power cycle

Repeat the steps again if unsuccessful.

Note: The projector’s on/off cycle may take longer to fully activate. It typically takes anywhere from 20-30

seconds for full off/on cycle to function each time.

For a local Elite Screens contact or technical support, please visit

www.elitescreens.com

DC 5-12V OUT

12V wireless trigger

Example of the back ofthe projector

5-12 v input port

Altri manuali per Vmax Series

Indice

Altri manuali Elite Screens Schermo di proiezione

Elite Screens

Elite Screens Yard Master Pro B Series Manuale utente

Elite Screens

Elite Screens Aeon CLR 3 Series Manuale utente

Elite Screens

Elite Screens Kestrel FE100H Manuale utente

Elite Screens

Elite Screens Electric100H Manuale utente

Elite Screens

Elite Screens VMAX113XWS Manuale utente

Elite Screens

Elite Screens Planate Tab-Tension Series Guida

Elite Screens

Elite Screens Home100IWH2-A Manuale utente

Elite Screens

Elite Screens Starling Tab-Tension Series Manuale utente

Elite Screens

Elite Screens Insta-DE Series Manuale utente

Elite Screens

Elite Screens StarBright7 Manuale utente

Elite Screens

Elite Screens Lights-On Portable Series Manuale utente

Elite Screens

Elite Screens M170XWS1 Manuale utente

Elite Screens

Elite Screens Kestrel Stage Series Manuale utente

Elite Screens

Elite Screens Elite Tripod Series Manuale utente

Elite Screens

Elite Screens Kestrel Stage Series Manuale utente

Elite Screens

Elite Screens SilverFrame 100GH1 Manuale utente

Elite Screens

Elite Screens Evanesce Tension Series Manuale utente

Elite Screens

Elite Screens ezFrame Plus Series Manuale utente

Elite Screens

Elite Screens Elite Manual Series Manuale utente

Elite Screens

Elite Screens Aeon CineGrey 4D AT Series Manuale utente

Elite Screens

Elite Screens Kestrel Home Series Manuale utente

Elite Screens

Elite Screens Tab-Tension 3 Series Manuale utente

Elite Screens

Elite Screens SilverFrame 100GH1 Manuale utente

Elite Screens

Elite Screens F100XWH1 Manuale utente

Manuali Schermo di proiezione popolari di altre marche

FART PRODUKT

FART PRODUKT Standard SCREEN Manuale utente

Draper

Draper E Series Manuale

Laarhoven

Laarhoven Companion II Manuale utente

Renogy

Renogy RMS-LFPS-US Manuale utente

Da-Lite

Da-Lite ExecutiveElectrol Manuale utente

Samsung

Samsung S*H65* Manuale utente

FONESTAR

FONESTAR PPTR-43100-FA Manuale utente

Slide Clear

Slide Clear Varro XL Manuale utente

OS РХ-090Н Manuale utente

Niko

Niko 10-845 Manuale utente

Speaka Professional

Speaka Professional 2357532 Manuale operativo

Sima

Sima XL-72 Manuale utente

Jasic

Jasic EVO 2.0 ET-200P Manuale utente

InFocus

InFocus SC-WALL GRY-92H Manuale

Barco

Barco OverView MVL-615 Manuale utente

Draper

Draper Envoy Manuale

SI Dynamic 2 XL Manuale utente

Draper

Draper Nocturne+ E Istruzioni per l'installazione