ELNA 505 Manuale utente
Service Manual
CONTENTS
SERVICE ACCESS
FACE COVER .................................................................................................................... 1
BELT COVER ..................................................................................................................... 2
BASE PLATE ..................................................................................................................... 3
FRONT COVER ................................................................................................................. 4
REAR COVER ................................................................................................................... 5
MECHANICAL ADJUSTMENT
PRESSER BAR HEIGHT AND ALIGNMENT .................................................................... 6
NEEDLE BAR HEIGHT ..................................................................................................... 7
MOTOR BELT TENSION ................................................................................................... 8
WIRING.............................................................................................................................. 9
1
SERVICE ACCESS (1)
(A)
(B)
Face plate
Rib
Rib
Rear cover
FACE COVER
TO REMOVE:
1. Remove the cap (a) and setscrew (B).
Unhook ribs from the rear cover. remove the face cover.
TO ATTACH:
2. Follow the above procedure in reverse.
2
(C)
Belt cover
BELT COVER
TO REMOVE:
1. Remove setscrew (C).
2. Take the belt cover out.
TO ATTACH:
3. Follow the above procedure in reverse.
(C)
SERVICE ACCESS (2)
3
(A)
Base plate
SERVICE ACCESS (3)
BASE PLATE
TO REMOVE:
1. Remove the setscrews (A).
2. Remove the base plate.
TO ATTACH:
3. Mount the base plate and secure it with four setscrews.
4
(A)
(B)
(E)
(D)
(F)
(G)
(H)
(J)
(C)
FRONT COVER
TO REMOVE:
1. Remove the face cover, and remove the belt cover (see page 1-2).
2. Loosen setscrews (A), (B), (C), (D), (E), and (F), remove setscrews (G) and (H), then remove the
front cover.
NOTE: Unhook the tab (J) from the rear cover when removing the front cover.
TO ATTACH:
3. Mount the front cover in reverse procedure of the removing.
Cap
SERVICE ACCESS (4)
5
Setscrew(A)
Setscrew(D)
Setscrew(C)
Setscrew(B)
Cap(K)
Setscrew(E)
Setscrew(F)
Setscrew(G)
Setscrew(J)
Setscrew(H)
Lower part (X)
UPPER
PART(Y)
Presser foot lifter part (Z)
Cover (L)
REAR COVER
TO REMOVE:
1. Remove the face cover, and remove the belt cover (see page 1-2).
2. Remove the setscrew (a) and the cover (L).
3. Remove the cap(k) and remove the screws (B), (C), (D) and (J).
4. Loosen the setscrew (E), (F), (G) and (H).
5. Remove the rear cover.
NOTE: Dismantle the rear cover in the order of the lower part (X), upper
part (Y), then presser foot lifter part (Z).
TO ATTACH:
6. Mount the rear cover in reverse procedure of the removing.
SERVICE ACCESS (5)
6
Presser foot
Needle plate
Screw(A)
Presser foot
lifter
Presser bar
Top of the needle plate
Bottom of the
presser foot
4mm
Presser
foot
PRESSER FOOT HEIGHT
4 mm (C)
Presser foot line
10 mm
Thumb screw
Bottom of the
needle bar (B)
2 mm
6 mm 8 mm
MECHANICAL ADJUSTMENT
PRESSER BAR HEIGHT AND ALIGNMENT
TO CHECK:
1. Lower the presser foot lifter.
2. The distance between bottom of presser foot and top of needle plate should be 4.0 mm (0.16") when the
presser foot is set at the standard position (The second line from the top aligns with the bottom of the
presser bar.)
ADJUSTMENT PROCEDURE:
1. Remove the face cover (see page 1).
Remove the lamp from the lamp socket, then lower the presser foot lifter.
2. Loosen the thumb screw. align the bottom of presser bar (B) and the second line (C) from the top on the
presser foot.
3. Adjust the distance between bottom of presser foot and top of needle plate to 4.0 mm.
4. Adjust the direction of the presser bar so the presser foot is parallel to the neelde plate. tighten the screw.
5. Attach lamp and face cover.
Thumb screw
7
Setscrew (A)
Eye guard (unit)
Needle unit
Setscrew (B)
Needle plate
16 mm
Needle bar
MECHANICAL ADJUSTMENT
NEEDLE BAR HEIGHT
When the needle bar is at its lowest position, the distance between the tip of the needle unit and the top of
needle plate should be in the range of 15.7-16.3 mm.
ADJUSTMENT PROCEDURE:
1. Attach the needle plate.
2. Turn the handwheel toward you until the needle bar reaches its lowest position.
3. Open the bed cover.
4. Loosen the setscrew (A) and remove the eye guard (unit).
5. Loosen the screw (B). Adjust the distance between the tip of the needle unit and needle plate to 16 mm.
6. Tighten the screw (B) and (A).
NOTE:
Be sure the needle unit does not interfear with the needle plate.
7. Close the bed cover plate.
8
300g Load
Deflection 7-9 mm
(B)
(A)
Motor
MECHANICAL ADJUSTMENT
MOTOR BELT TENSION
TO CHECK:
1. Improper belt tension may cause noise, overload of motor, slow running or motor belt jumping.
2. The belt deflection should be 7 mm - 9 mm when pressing the middle of the motor belt with
approximately 300 grams of pressure.
ADJUSTMENT PROCEDURE:
1. Remove the belt cover (see page 4).
2. Loosen the screws (A) and (B).
3. Move the motor up or down to adjust the deflection about 7 mm -9 mm.
4. Tighten the screws (A) and (B).
5. Attach the belt cover.
Indice
Altri manuali ELNA Macchina da cucire
ELNA
ELNA 5100 - Manuale utente
ELNA
ELNA 664PRO - Manuale utente
ELNA
ELNA 745 - Manuale utente
ELNA
ELNA 434 - LEAFLET Manuale utente
ELNA
ELNA Elnita ec60 Manuale utente
ELNA
ELNA TSP AIR ELECTRONIC Manuale utente
ELNA
ELNA Elina 21 Manuale utente
ELNA
ELNA Carina Manuale utente
ELNA
ELNA 8200 Manuale utente
ELNA
ELNA 9900 - LEAFLET Manuale utente
ELNA
ELNA eXcellence 760 Manuale utente
ELNA
ELNA 8007 Schema elettrico
ELNA
ELNA eXtend 864air Manuale utente
ELNA
ELNA eXplore 320 Manuale utente
ELNA
ELNA eXperience 660 Manuale utente
ELNA
ELNA Lotus Manuale utente
ELNA
ELNA XPRESSIVE 2 Manuale utente
ELNA
ELNA XQUISIT 2 Manuale utente
ELNA
ELNA 7100 Manuale utente
ELNA
ELNA eXcellence 710 Manuale utente
