Elo Touch Solutions IDS 3201L Manuale utente
User Guidel–Computer Module
SW602000 Rev A, Page 2 of 20
Copyright © 2013 Elo Touch Solutions, Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language or computer language, in any form or by any means, including, but not limited to, electronic,
magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc.
Disclaimer
The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its affiliates
(collectively "Elo") makes no representations or warranties with respect to the contents herein, and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Elo reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of Elo to
notify any person of such revisions or changes.
Trademark Acknowledgments
AccuTouch, CarrollTouch, Elo (logo), Elo Touch Solutions, Elo TouchSystems, IntelliTouch, iTouch are trademarks of
Elo and itsAffiliates. Windows is a trademark of Microsoft Corporation.
US052332DMSADM - 2013-03-04T23:11:16Z
User Guidel–Computer Module
SW602000 Rev A, Page 3 of 20
Table of Contents
Chapter 1 - Introduction ........................................................................... 4
Chapter 2 – Unpacking.............................................................................. 5
Chapter 3 – Computer Module Installation........................................ 6
Chapter 4 – Technical Support............................................................... 11
Chapter 5 – Safety & Maintenance........................................................ 12
Chapter 6 – Regulatory Information ................................................... 17
Chapter 7 – Warranty ............................................................................... 19
US052332DMSADM - 2013-03-04T23:11:16Z
User Guidel–Computer Module
SW602000 Rev A, Page 4 of 20
Chapter 1 - Introduction
Product Description
Interactive Digital Signage Computer Module Gen 2 is designed to slide into the bay on the rear
of the Interactive Digital Signage Gen 2 touchmonitors, without any effect on the monitor’s
form factor or requiring any extra cabling, turning your Interactive Digital Signage TouchMonitor
into an Interactive Digital Signage All-In-One TouchComputer.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user’s manual to
maximize the life of your unit and prevent risks to user safety.
This manual contains information that is important for the proper setup and maintenance of the
Computer Module. Before setting up and powering on your new computer module, read through
this manual, especially the Installation chapter.
US052332DMSADM - 2013-03-04T23:11:16Z
User Guidel–Computer Module
SW602000 Rev A, Page 5 of 20
Chapter 2 – Unpacking
Unpacking the The Digital Signage Computer Module
Check that the following items are present and in good condition:
•Computer Module
•User Guide/ Driver CD
•Quick Install Guide
•PC Box Cable Cover
US052332DMSADM - 2013-03-04T23:11:16Z
User Guidel–Computer Module
SW602000 Rev A, Page 6 of 20
Chapter 3
Computer Module Installation
Installation
1. Use a Phillips head screwdriver to remove the access cover plate on the back of the
touchmonitor.
2. Slide the Computer Module all the way into the bay until it snaps into place.
3. Tighten the thumbscrews to secure the computer module inside the bay.
NOTE: If any cables are connected to the computer module, a cable security cover is
included with the computer module kit. Install it by attaching the mounting clip and bracket as
shown in the user guide for the computer module and then fastening the thumbscrews on the
cover.
US052332DMSADM - 2013-03-04T23:11:16Z
User Guidel–Computer Module
SW602000 Rev A, Page 7 of 20
Connector Panel & Interfaces
Touchmonitor & Computer Module Connections
1. Once the Computer Module has been installed, connect the AC power cable between
the touchmonitor’s POWER IN connector and the AC power source.
NOTE: Computer Module can be installed whenAC power cable is connected (Hot
pluggable). Do not remove the computer module unless it is completely shut off.
2. Make any desired connections to the Computer Module connector panel.
3. Press the touchmonitor’s power button 2 seconds to turn on the Computer Module.
US052332DMSADM - 2013-03-04T23:11:16Z
User Guidel–Computer Module
SW602000 Rev A, Page 8 of 20
Operating System Setup
Windows®7 Operating Systems
The initial setup of the operating system takes approximately 5 minutes. Additional time might
be needed for different touchcomputer hardware and operating system configurations. You
will need to plug in an external mouse and/or keyboard into the Computer Module connector
panel to execute these steps.
To set up the Windows 7 OS for the Computer Module, turn on the touchcomputer and follow
the instructions on the screen.
Selecting the Language
Windows uses English as the default language in menus and dialog boxes. You can change
this language to suit your preference.
Choosing the computer name
You will be prompted to enter the computer’s name.
Choosing the Windows Update settings
You will be prompted to select the Windows Update settings.
US052332DMSADM - 2013-03-04T23:11:16Z
User Guidel–Computer Module
SW602000 Rev A, Page 9 of 20
Selecting the Time Zone
When the following window appears, you can change the Computer Module’s time zone, date,
and time. After making any changes, click Next to finish. Windows Setup completes the OS
installation.
US052332DMSADM - 2013-03-04T23:11:16Z
User Guidel–Computer Module
SW602000 Rev A, Page 10 of 20
Installing the Touchscreen Technology Software Drivers
for Elo Computer Modules with Windows 7
Visit the Elo Touch Solutions website www.elotouch.com for:
•The latest touch driver versions
•Additional touch driver information
•Detailed touch driver installation guides
•Touch drivers for other operating systems
The Computer Module has the Elo Touch Driver already installed on the computer. This touch
driver along with the Computer Module driver pack will be available in the CD that ships with the
computer module
Operating System Setup – No OS
No Operating System (No OS) units will require an operating system to be installed on them.
Load your desired operating system onto the Computer Module. The easiest way to do this
will probably be using an image or recovery disk on a USB external DVD-ROM drive connected
to the Computer Module.
Cancel any attempts by your operating system to load drivers for the new USB device (the Elo
touchscreen) it finds.
Once you have installed an OS image on your computer, allow the system to automatically
install all the available drivers. You can download the latest Elo Touch Driver from the website
mentioned above and proceed to install that driver on the computer, or you can use the CD that
ships with the computer module to access the touch driver and the computer module driver
pack.
Installing the Touchscreen Technology Software Drivers
for Elo Computer Modules with No OS
Visit the Elo Touch Solutions website www.elotouch.com for:
•The latest versions of our touch drivers
•Additional touch driver information
•Detailed touch driver installation guides
•Touch drivers for other operating systems
Download and install the required touch driver from the Elo Touch Solutions website
www.elotouch.com.
US052332DMSADM - 2013-03-04T23:11:16Z
Altri manuali per IDS 3201L
2
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Elo Touch Solutions Terminale touch
