Elvid OCM-10-PSM Manuale utente

USER

MANUAL

FIELDVISION

OCM-10-PSM

10.1″PRO LCD MONITOR

Thank you for choosing Elvid.

The Elvid OCM-10-PSM FieldVision 10.1″Pro LCD Monitor with Scopes is perfect as a

director’s monitor. Its signature all-scopes setting displays a histogram, audio column,

vector, RGB histogram, and YUV waveform on the sides with an uninterrupted view of your

incoming video frame, enabling instant and constant feedback without disrupting your view

of the image. Anamorphic mode can be set to 1.3× or 2.0× to offer an accurate view of your

picture’s aspect ratio when shooting with an anamorphic lens.

The unique nine-grid mode divides the frame into a 3 × 3 grid as a composition aid and

allows you to magnify a specic area without adjusting your frame. A zebra exposure

indicator and false color mode with onscreen key display provide visual guides so you can

achieve precise exposure levels. A focus assist tool with two sensitivity levels helps ne-tune

your focus. There are also broadcast-specic features like overscan, safety frame markers,

and a tally light.

The FieldVision is equipped with Video, YPbPr, HDMI, and two SDI inputs—all with loop-

through—making this monitor compatible with most pro-video connections. Native resolution

is 1280 × 800, and you can easily change the native 16:10 aspect ratio to t your needs.

Onboard controls include ve function buttons that can be programmed from a palette of

22 functions and saved in three independent groups. Four knobs facilitate menu navigation,

access focus and Camera (DSLR) modes, and adjust monitor settings. There’s also an

integrated mono speaker and a 3.5 mm stereo headphone output for live audio monitoring.

INTRODUCTION

• Please read and follow these instructions and

keep this manual in a safe place.

• Exposure to high sound levels can cause

permanent hearing loss. Avoid listening at

high volumes for extended periods of time.

• Keep this product away from water and any

ammable gases or liquids.

• Make sure this product is powered off when

plugging it into a power source.

• Use only the correct, recommended voltage.

• Do not attempt to disassemble or repair this

product.

• Do not place or store the FieldVision

facedown, since this can damage the screen.

• Handle this product with care. Avoid any

unnecessary impacts to this product.

• Do not block the vents in this product.

• Disconnect this product from its power source

before storage and during electrical storms.

• Do not use chemical solutions to clean this

product. Clean this product with only a soft,

dry cloth.

• Keep this product away from children.

• Make sure that this product is intact and that

there are no missing parts.

• To avoid damage to this product, be careful

not to overtighten or improperly thread any

of the threaded ttings.

• All photos are for illustrative purposes only.

PRECAUTIONS

TABLE OF

CONTENTS

Precautions.............................................. 3

Product Contents ................................... 5

Overview .................................................. 6

Powering the FieldVision ..................... 8

Monitoring Sound................................... 9

Mounting the FieldVision..................... 9

Connecting to Your Camera ................. 9

Loop Through .......................................... 9

Tally Connection ..................................... 9

The Sunshade........................................ 10

The Menu ................................................ 11

Navigating the Menu............................ 11

Assistant Functions Menu .................. 11

Check Field ............................................. 11

Pseudo Color .......................................... 11

Zebra Crossing....................................... 11

Focus Assist ........................................... 11

Focus Color ............................................. 11

Pattern Gen ............................................ 11

Marker Display Menu........................... 11

Center Marker........................................ 11

Marker Type............................................12

Safety Area.............................................12

Marker Color...........................................12

Nine Grid .................................................12

Scopes Menu ..........................................13

Y Histogram............................................13

Audio Column.........................................13

Vector.......................................................13

RGB Histogram ......................................13

Waveform................................................13

All Scopes................................................13

Picture Setting Menu ...........................14

Scan Mode ..............................................14

Camera Mode .........................................14

Flip............................................................14

Freeze.......................................................14

Pixel to Pixel ..........................................14

Zoom ........................................................14

Anamorphic ............................................14

Color Setting Menu...............................15

Color Temp ..............................................15

Red, Green, and Blue............................15

Shortcuts Menu .....................................15

Shortcut Group ......................................15

OSD Setting Menu.................................16

Language.................................................16

OSD Time.................................................16

OSD Trans ...............................................16

Volume.....................................................16

Mute.........................................................16

Reset ........................................................16

SW Version .............................................16

Specications .........................................17

Supported Resolutions and Frame Rates 18

Troubleshooting.....................................19

One-Year Limited Warranty.........(Back) 20

PRODUCT

CONTENTS

·10.1″Field Monitor

·Sunshade

·Sunshade thumbscrews (×2)

·Tabletop bracket

·Tabletop bracket thumbscrews (×2)

·Adhesive touch strip

·Tally kit

·4-pin XLR power supply

·AC power cable

·User manual

OVERVIEW

Brightness/Esc knob

Contrast/Focus knob

Headphone jack

Function buttons

(F1, F2, F3, F4, F5)

Speaker

Selector/Menu knob

Volume/Camera knob

Video input buttons

(Video, YPbPr, HDMI, SDI 1, SDI 2)

Power LED

Screen

1/4″-20 threaded sockets

Tally Light

Power switch

Tally connector

Battery plate

SDI ports

DC power input HDMI input

YPbPr component

video ports

Audio inputs

XLR input HDMI output

POWERING THE

FIELDVISION

There are three ways to power the

FieldVision: 4-pin XLR input, 12 V DC

input, and a Sony L-Series camera

battery.

4-PIN XLR

To power the FieldVision via the 4-pin

XLR input, use a 4-pin XLR power supply

and AC power cable to connect the

FieldVision’s 4-pin XLR DC power input

to your power source.

To power the FieldVision via the 4-pin

XLR input, follow these steps:

1. Fully insert a 4-pin XLR power supply

into the 4-pin XLR DC power input on

the back of the monitor. The connector

should click into place when fully

inserted.

2. Use an AC power cable to connect

the XLR power supply to your AC power

source.

To turn on the FieldVision, press the

power switch to the On position. The

power indicator LED will glow green.

12 V DC INPUT

To power the FieldVision via the 12 V DC

input, use a 12 V DC adapter with the

included 2.1 mm DC barrel to connect

the FieldVision’s DC power input to your

AC power source.

To turn on the FieldVision, press the

power switch to the On position. The

power indicator LED will glow green.

CAMERA BATTERY

The FieldVision has a built-in battery

plate that accepts all Sony L-Series

batteries. This allows you to power the

FieldVision with readily-available battery

packs that you may already own.

To power the FieldVision with a Sony

L-Series battery (not included), follow

these steps:

1. Place a compatible battery in the

battery plate. Make sure the battery’s

bottom contacts are aligned with the

contacts in the battery plate.

2. Slide the battery forward until it locks

into place.

To turn on the FieldVision, press the

power switch to the On position. The

power indicator LED will glow green.

GETTING

STARTED

MONITORING SOUND

You can monitor sound via the

integrated speaker or the 3.5 mm

stereo headphone jack. To monitor via

the headphone jack, plug in a pair of

compatible headphones.

MOUNTING THE FIELDVISION

Use one of the 1/4″-20 threaded sockets

in the FieldVision to attach the monitor

to your mounting system. Make sure

your bracket can support the monitor.

Alternatively, you can mount the

included tabletop bracket by attaching it

with the included bracket thumbscrews.

CONNECTING TO YOUR CAMERA

To connect the FieldVision to your

camera, follow these steps:

1. Choose the desired video signal, and

use the appropriate cable to connect

your camera to the corresponding input

connections on the back of the monitor.

2. Press the video input button

(composite video, YPbPr, HDMI, SDI1,

or SDI2) that corresponds to your video

input signal.

LOOP THROUGH

The FieldVision is equipped with loop-

through, also known as pass-through, for

all of its video inputs. To loop the video

signal through the monitor, connect your

camera to the desired video input, and

then connect the appropriate cable to

the corresponding output on the back of

the monitor.

TALLY CONNECTION

If desired, you can connect your tally

cable to the FieldVision’s RS232

D-sub 9-pin tally connector or the

included bare-end adapter. Refer to the

included insert for the specic tally pin

connections.

THE

SUNSHADE

THE SUNSHADE

The sunshade prevents glare on the

monitor’s screen by blocking out stray

light and is useful when shooting

outdoors. To attach the included

sunshade, follow these steps:

1. Unfold the sunshade and place it along

the top and sides of the monitor.

Tip: For a more secure t, attach the

included adhesive touch strip along the

top edge of the monitor. This will help

hold the sunshade in position.

2. Align the sunshade’s screw holes with

the 1/4″-20 threaded sockets in the sides

of the monitor.

3. Use the included thumbscrews to

fasten the sunshade in place.

Indice

Altri manuali Elvid Monitor

Elvid

Elvid WCM-758G SkyVision Manuale utente

Elvid

Elvid OCM-7P-HDR Manuale utente

Elvid

Elvid SKYVISION WCM-55-HD Manuale utente

Elvid

Elvid OCM-7PWV Manuale utente

Elvid

Elvid RVM-7B-ALT Manuale utente

Elvid

Elvid Studiovision STV-150-4KH Manuale utente

Elvid

Elvid OCM-7B-4KV2 Manuale utente

Elvid

Elvid STUDIOVISION SRM-7X2-4KH Manuale utente

Elvid

Elvid RIGVISION RVM-5P-HDR Manuale utente

Elvid

Elvid RigVision CM-7L Manuale utente

Elvid

Elvid FIELDVISION OCM-89-4KH Manuale utente

Elvid

Elvid OCM-7B-D FieldVision Manuale utente

Elvid

Elvid OCM-101-4KH Manuale utente

Elvid

Elvid StudioVision STV-280-4KHDR Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione