Emerson SR110 Manuale utente

Part No. F40BP72700000 Form No. BP7270

READ AND SAVE THESE INSTRUCTIONS

SR110 & SW105

Ceiling Fan/Light

Remote Control & Receiver

Owner's Manual

For use only with Emerson Ceiling Fan Models

F2100 1, F2200 1, F2300 1, CF1 0, CF2300 0, CF2400 1,

CF2500 0, CF2800 0, CF3900 0, CF4500 1, and CF4800 1.

OFF

REV

LOW

MED

HIGH

UP DN

Model

SR110

Remote Control

Model

SW105

Receiver

NOTE: The SR110 Remote

Control must be used with

a SW105 Receiver.

BP7270-1 5/6/05 1:29 PM Page 1

Safety Instructions

WARNING: To avoid fire, shock, and serious personal injury, follow all instructions

carefully.

1. Read your Owner's Manual carefully before installing the Remote Control or Receiver.

Retain Owner's Manual for future reference.

2. Before servicing or cleaning the ceiling fan, switch power off at service panel and lock

service panel to prevent power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a warning device such as a

tag, to the service panel.

ADDITIONAL SAFETY INSTRUCTIONS FOR INSTALLATION

1. To avoid possible electrical shock, be sure electricity is turned off at the main fuse or

circuit breaker box before wiring.

2. Make certain no bare wires are exposed outside the wire connectors.

3. All wiring must conform to National and Local Electrical Codes.

4. Follow the recommended instructions for the proper method of wiring your new

Remote Control or Receiver. If you feel you do not have enough electrical wiring

knowledge or experience, have your Remote Control or Receiver installed by a

licensed electrician. Any electrical work not described in this manual should be

performed by a licensed electrician.

WARNING

DATE CODE:

The date code of this fan may be found on the box, stamped in ink on a white label.

You should record this data above and keep it in a safe place for future use.

INSTRUCTION TO THE USER (if device contains a digital device)

This equipment has been tested and found to comply with the limits for a class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This equipment has been certified to comply with the limits for a class B computing device,

pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded cables

must be used with this equipment. Operation with non-approved equipment or unshielded

cables is likely to result in interference to radio and TV reception. The user is cautioned that

changes and modifications made to the equipment without the approval of manufacturer could

void the user’s authority to operate this equipment.

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

BP7270-1 5/6/05 1:29 PM Page 2

General

Your Emerson Ceiling Fan/Light Control

consists of a hand-held SR110 Remote

Control (transmitter) and a SW105

Receiver which is mounted under the fan

ceiling cover. The remote control is

designed to control your ceiling fan speed,

airflow direction, and light intensity.

NOTE: The remote control is to be used

only with the following Emerson ceiling

fan models: F2100, F2200, CF1,

CF2300, CF2400, CF2500, CF2800,

CF3900, CF4500 and CF4800.

The SW105 Receiver may also be used

with the SW115 Wall Control.

Unpackaging

The carton with the SR110 Remote

Control transmitter also contains a storage

bracket with two mounting screws.

The carton with the SW105 Receiver also

contains a reversing module, seven wire

connectors, and four pull chain switch

plugs. Preset Memory Feature

Your Emerson remote control receiver is

equipped with a preset memory feature.

The receiver will remember the light

intensities and fan speed when the lights

and fan are turned off from the wall switch.

When the wall switch is turned back on,

the lights and fan will resume operation as

they were prior to being turned off.

Installation of Battery

1. Remove the battery cover and install

four AAA batteries (not supplied),

oriented as shown in the battery

compartment (Figure 1).

IMPORTANT

This Owner’s Manual is divided into

two sections. The first section,

REMOTE CONTROL PROCEDURES,

describes how to install the four

alkaline batteries (not supplied) in the

remote control transmitter, and how to

set the operating frequency of the

transmitter and receiver. These

instructions must be performed prior to

installation of the ceiling fan as

described in the second section,

CEILING FAN PROCEDURES.

REMOTE CONTROL

PROCEDURES

General

Your Emerson Ceiling Fan/Light Remote

Control consists of a hand-held transmitter

and a receiver which is mounted under the

fan ceiling cover. The remote control is

designed to separately control your ceiling

fan and light intensities. There are four

push buttons (HI, MED, LOW, OFF) to set

the fan speed and turn the fan off.

The REV push button changes the airflow

direction of the fan blades. The UP

(uplight) and DN (downlight) push buttons

turn the lights on and off and control the

light intensities. The red indicator light will

illuminate while any button is pressed,

indicating that the battery is good.

The remote control transmitter is powered

by four AAA alkaline batteries (not

supplied). To prevent possible damage if

the batteries should leak, be sure to

remove the batteries when the control is

not to be used for an extended period of

time.

Code switches in the transmitter and

receiver may be set in 16 different

positions. If your fan and light go on and

off without using your control, you may be

getting interference from other remote

units such as garage door openers, car

alarms or security systems. To remedy this

situation, simply change the combination

code in your transmitter and receiver.

SWITCH LEVERS

CODE SWITCH

REMOTE CONTROL

TRANSMITTER

CODE

SWITCH RECEIVER

CODE

SWITCH

BATTERY

COVER

AAA

2341

Figure 1

BP7270-1 5/6/05 1:29 PM Page 3

Setting Operating

Frequency of Transmitter

and Receiver

Your remote control transmitter and

receiver have code switches which must

be set on one of 16 possible code

combinations. The four levers (numbered

1, 2, 3, and 4) on the switches are factory-

set in the ON (up) position. Do not use this

setting. Change the switch settings as

follows:

1. Slide the four switch levers (Figure 1) in

the remote control transmitter to your

choice of ON (up) or down positions.

Use a ball-point pen or small

screwdriver and slide the levers firmly

up or down.

2. In the receiver, slide the four switch

levers in the same positions as set in

the transmitter. Make sure the levers on

both switches are in the same

positions; otherwise the fan will not

operate.

3. Position the batteries in the transmitter

battery compartment and replace the

battery cover.

CEILING FAN

PROCEDURES

Installation to Operate the

Ceiling Fan, Downlight

and Uplight

IMPORTANT

It is important that you also follow the

installation instructions contained in

the Owner’s Manual supplied with your

Ceiling Fan. Pay particular attention to

the Safety Instructions and WARNING

notes.

1. Remove and retain the screws

securing the housing cover to the

switch housing (Figure 2).

2. All Ceiling Fan Models. Disconnect

the motor connector from the wiring

harness connector (Figure 2). Remove

the knurled nut securing the speed

control switch to the switch housing.

HOUSING COVER

(TYPICAL)

SCREW (TYPICAL)

SCREW (2)

KNURLED

NUT

SPEED

CONTROL

SWITCH

PULL

CHAIN PLUG REVERSING SWITCH

SWITCH HOUSING

CAPACITOR

MOTOR

CONNECTOR

WIRING

HARNESS

CONNECTOR

Figure 2

3. For Ceiling Fan Models CF2400,

CF4500 and CF4800 Only. Remove

the wire connector joining the three

blue wires. (Figure 3). Separate the

blue wire coming from the ceiling fan

and cap this wire using a wire

connector (supplied). On Models

CF4500 and CF4800 only, cut the

yellow wire coming from the uplight

switch; cap the end of this wire coming

from the center of the motor using a

wire connector. On Model CF2400 only,

remove the wire connector joining the

two yellow wires; cap the yellow wire

coming from the motor using a wire

connector (orange wire on older

models). Remove the knurled nut

securing the uplight switch to the switch

housing and remove the uplight switch.

NOTE: Keep the uplight switch if you

think you may like to return to manual

control in the future.

PULL CHAIN

PLUG

UPLIGHT SWITCH

CUT THE

YELLOW WIRE

AND CAP USING

WIRE

CONNECTOR

SEPARATE BLUE WIRE COMING FROM CEILING

FAN AND CAP USING WIRE CONNECTOR

REMOVE WIRE

CONNECTOR SECURING

THREE BLUE WIRES

KNURLED NUT

Figure 3

BP7270-1 5/6/05 1:29 PM Page 4

5. For Ceiling Fan Models F2100, F2200

and CF2300 Only. Remove the knurled

nut securing the reversing switch to the

switch housing (Figure 4).

6. For Ceiling Fan Models CF1 and

CF2800 Only. Locate the gray

capacitor wire which is connected to

the yellow wire (gray wire on older

models) coming from the center of the

motor. Remove the wire connector and

separate the gray and yellow wires.

Cap the yellow wire using a wire

connector (supplied) (Figure 5).

KNURLED

NUT

PULL

CHAIN

PLUG

REVERSING SWITCH

Figure 4

WIRE CONNECTOR

REVERSING

MODULE

MOTOR

CONNECTOR

WHITE

REVERSING

MODULE WIRE

WHITE MOTOR

WIRE

REVERSING MODULE

CONNECTOR

CF1 & CF2800 INSTALL

WIRE CONNECTOR ON

YELLOW WIRE

(CF2400 - INSTALL

WIRE CONNECTOR ON

GRAY WIRE)

CF1 & CF2800

YELLOW WIRE (GRAY

ON OLDER MODELS

AND ON CF2400)

GRAY

CAPACITOR

WIRE

CAPACITOR

Figure 5

7. All Ceiling Fan Models. Separate the

capacitor (held in place with two-sided

tape) from the switch housing (Figure

2) and remove the wiring harness and

switch(es) from the switch housing.

NOTE: Keep the wiring harness if you

think you may like to return to manual

control in the future.

8. All Ceiling Fan Models. Close the

hole(s) for the speed control switch and

the uplight switch or reversing switch

by installing pull chain plug(s)

(supplied) in the hole(s). (See Figures

2, 3, and 4). Choose the color that best

matches our ceiling fan.

9. Position the reversing module

(supplied) in the switch cup; connect

the reversing module connector to the

motor connector (Figure 6). The

connectors are color-coded and keyed

and can be connected in only one

manner.

Figure 6

10. Using a wire connector (supplied),

connect the white wire from the motor

to the reversing module white wire

(Figure 6).

11. Position the housing cover (Figure 2)

on the switch housing and secure

using the screws removed in Step 1.

NOTE: If you are planning to install an

optional Emerson Light Fixture on your

ceiling fan, do not install the housing

cover (Step 11) at this time.

12. Place the fan housing (top of motor

facing upward) in the lower styrofoam

pad. The lower pad serves as a

holder for the fan during the following

procedures.

6A. For Ceiling Fan Model CF2400

Only. Locate the gray capacitor wire

which is connected to the gray wire

coming from the center of the motor

(yellow wire on older models).

Remove the wire connector and

separate the gray wires. Cap the gray

wire using a wire connector (supplied)

(Figure 5).

4. For Ceiling Fan Models CF2500,

CF3900, CF4500 and CF4800 Only.

Remove two screws securing the

reversing switch to the switch housing

(Figure 2).

BP7270-1 5/6/05 1:29 PM Page 5

13. For Ceiling Fan Models F2100,

F2200, CF2300, CF2500 and

CF3900 Only. Locate and remove the

connector from the yellow wire from

the uplight (Figure 7). Separate,

untwist and unkink the 80” yellow wire

lead (supplied with the fan) and cut off

the connector from the end of the

wire. Strip 1/2-inch of insulation from

the end of this wire. Then join the 80”

yellow wire to the yellow wire from the

uplight using a wire connector

(supplied).

NOTE: The red and brown wires

coming from the top of the motor are

capped with wire connectors. DO NOT

remove these connectors.

80" YELLOW WIRE

BROWN

WIRE

DO NOT REMOVE THESE

WIRE CONNECTORS

RED WIRE YELLOW WIRE

FROM UPLIGHT

REMOVE WIRE CONNECTOR

FROM YELLOW WIRE FROM

UPLIGHT

JOIN 80" YELLOW WIRE

USING WIRE CONNECTOR

Figure 7

14. For Ceiling Fan Models CF4500

and CF4800 Only. Locate the two

yellow wires terminated by a wire

connector. Remove the wire

connector and separate the wires

(Figure 8). One yellow wire comes

from the motor coupling; cap the end

of this wire using a wire connector

(supplied) (Figure 9). Separate,

untwist and unkink the 80” yellow wire

lead (supplied with the fan) and cut off

the connector from the end of the

wire. Strip 1/2-inch of insulation from

the end of this wire. Then join the 80”

yellow wire to the yellow wire from the

uplight using a wire connector

(supplied). (Figure 9).

NOTE: The red and brown wires

coming from the top of the motor are

capped with wire connectors. DO NOT

remove these connectors.

14A. For Ceiling Fan Models CF2400

Only. Cut the yellow wire midway

between the motor coupling and the

grommet in the inside of the housing

(orange wire on older CF2400

models). Cap the yellow wire coming

from the motor coupling using a wire

connector (supplied). Separate,

untwist and unkink the 80” yellow

wire lead (supplied with the fan) and

cut off the connector from the wire.

Strip 1/2-inch of insulation from the

end of this wire. Then join the 60”

yellow wire to the yellow wire coming

from the inside of the housing using

a wire connector.

YELLOW WIRE FROM

MOTOR COUPLING

BROWN

WIRE

DO NOT REMOVE THESE

WIRE CONNECTORS

RED WIRE YELLOW WIRE

FROM UPLIGHT

REMOVE WIRE

CONNECTOR

MOTOR COUPLING

Figure 8

INSTALL WIRE

CONNECTOR

INSTALL 80" YELLOW WIRE

BROWN

WIRE

DO NOT REMOVE THESE

WIRE CONNECTORS

YELLOW WIRE

FROM UPLIGHT

RED WIRE MOTOR

COUPLING

YELLOW WIRE

FROM MOTOR COUPLING

INSTALL

WIRE

CONNECTOR

Figure 9

15. For Ceiling Fan Models CF1 and

CF2800 Only. No wiring changes are

required on top of the motor; proceed

to Step 16.

BP7270-1 5/6/05 1:29 PM Page 6

The hairpin clip must be properly

installed to prevent the clevis pin from

working loose. Pull on the downrod to

make sure the clevis pin is properly

installed.

19. Install the setscrew (supplied with

ceiling fan) in the motor coupling

(Figure 11). While pulling up on the

downrod, tighten the setscrew using

the 5/32” setscrew wrench (supplied

with ceiling fan).

NOTE: The setscrew must be properly

installed as described above, or fan

wobble could result.

20. Screw two 1” threaded studs

(supplied with ceiling fan) into the

motor (Figure 12). Leave approxi-

mately 7/8” of the stud extending

above the motor. Slide the motor

cover over the downrod and rotate the

cover until the threaded studs

protrude; install two knurled knobs

(supplied with ceiling fan).

NOTE: Make sure the red and brown

leads are capped with wire connectors

and all wires are completely inside

motor cover and not pinched between

the motor cover and motor.

16. Remove the hanger ball by loosening

the setscrew in the hanger ball until

the ball falls freely down the downrod

(Figure 10). Remove the pin from the

downrod, then remove the hanger

ball. Retain the pin and hanger ball for

reinstallation in Step 22.

17. Separate, untwist and unkink the 80”

white, black, and blue motor lead

wires. Route the three motor leads

and the 80” yellow lead wire (used

only on fans with uplight) through the

downrod. Seat the downrod firmly in

the motor coupling (Figure 11).

18. Align the clevis pin holes in the

downrod with the holes in the motor

coupling. Install the clevis pin

(supplied with the ceiling fan) and

secure with the hairpin clip (Figure

11). The clevis pin must go through

the holes in the motor coupling and

the holes in the downrod. Push the

straight leg of the hairpin clip through

the hole near the end of the clevis pin

until the curved portion of the hairpin

clip snaps around the clevis pin.

DOWNROD

CLEVIS PIN

SETSCREW

HANGER

BALL

Figure 10

SETSCREW

CLEVIS PIN MOTOR

COUPLING

DOWNROD

HAIRPIN

CLIP

DOWNROD

MOTOR COUPLING

CLEVIS

HAIRPIN

CLIP SETSCREW

Figure 11

It is critical that the pin in the hanger ball

is properly installed and the setscrew

securely tightened. Failure to verify that

the pin and setscrew are properly

installed could result in the fan falling.

WARNING

KNURLED KNOB (2)

MOTOR COVER

1" THREADED

STUD (2)

RED AND BROWN WIRES

Figure 12

BP7270-1 5/6/05 1:29 PM Page 7

21. Position the ceiling cover over the

downrod (Figure 13). Be sure the

cover is oriented correctly, with the

large opening at the top.

22. Reinstall the hanger ball on the

downrod (Figure 13) as follows.

Route the motor leads through the

hanger ball and slide the hanger ball

over the downrod. Install the pin

through the holes at the top of the

downrod and slide the hanger ball up

the downrod, aligning the ball so the

pin is captured in the groove in the top

of the hanger ball. Pull the hanger ball

up tight against the pin and securely

tighten the setscrew in the hanger

ball. A loose setscrew could create

fan wobble.

23. Cut the wire leads from the downrod

approximately 6-inches above the

hanger ball. Strip back insulation 1/2-

inch from the end of the leads.

It is critical that the pin in the hanger ball

is properly installed and the setscrew

securely tightened. Failure to verify that

the pin and setscrew are properly

installed could result in the fan falling.

WARNING

SETSCREW

DOWNROD

HANGER BALL

CEILING

COVER

Figure 13

24. Install the hanger bracket and hang

the fan in accordance with the

instructions in the Ceiling Fan

Owner’s Manual.

25. Pull the wire leads, coming from the

end of the downrod, and the supply

wires through the open side of the

hanger bracket. (Figure 14).

26. Position the SW105 Receiver in the

ceiling cover so that the flat side of

the receiver faces up and the open

portion of the receiver is to the right,

as shown in Figure 14.

OUTLET BOX

BLACK SUPPLY WIRE

BLACK/WHITE RECEIVER WIRE

BLACK FAN WIRE

BLUE FAN WIRE

BLUE RECEIVER

WIRE

YELLOW FAN WIRE

YELLOW RECEIVER WIRE

CEILING COVER

WHITE RECEIVER WIRE

WHITE FAN WIRE

WIRE CONNECTOR

RECEIVER

WHITE SUPPLY

WIRE

SUPPLY GROUND

WIRE (GREEN OR

BARE)

HANGER BALL

GROUND WIRE

(GREEN)

HANGER BRACKET

GROUND WIRE

(GREEN)

HANGER BRACKET

BLACK RECEIVER WIRE

OPEN

PORTION OF

RECEIVER

HERE

Figure 14

BP7270-1 5/6/05 1:29 PM Page 8

DOWNROD

MOTOR COUPLING

FAN HOUSING

OPTIONAL

LIGHT FIXTURE

YELLOW UPLIGHT WIRES

(NOT PRESENT ON ALL FANS)

RED AND BROWN

WIRES - CAPPED.

DO NOT REMOVE

WIRE CONNECTORS

WHITE SUPPLY WIRE

BLACK FAN WIRE

SW105 RECEIVER TO

110V SUPPLY LISTED GENERAL

USE ON/OFF WALL

SWITCH OR

OPTIONAL

EMERSON SW115

WALL CONTROL

YELLOW RECEIVER WIRE**

WHITE FAN WIRE BLUE RECEIVER WIRE*

BLUE FAN WIRE

BLACK

SUPPLY

WIRE

WHITE RECEIVER WIRE

BLACK RECEIVER WIRE

BLACK/WHITE RECEIVER WIRE

* IF YOUR CEILING FAN DOES NOT

HAVE A DOWNLIGHT, CAP THE BLUE

RECEIVER WIRE USING A WIRE

CONNECTOR.

** IF YOUR CEILING FAN DOES NOT

HAVE AN UPLIGHT, THERE WILL BE

NO YELLOW FAN WIRE.

IN THIS CASE, CAP THE YELLOW

RECEIVER WIRE USING A WIRE

CONNECTOR.

EMERSON

MED

LOW

FANOFF

ONOFF

REV

D/L

U/L

YELLOW FAN WIRE

(FROM UPLIGHT)

Figure 15

27. Using wire connectors (supplied),

make wiring connections as follows

(Figure 14 and 15):

a. Connect the green ground wires

from the hanger bracket and the

hanger ball to the supply ground

wire (bare or green).

b. Connect the white fan wire and the

white supply wire to the white

receiver wire (AC IN/MOTOR N).

c. Connect the black fan wire to the

black receiver wire (TO MOTOR

L).

d. Connect the black supply wire to

the black/white receiver wire (AC

IN L).

e. Connect the blue fan wire to the

blue receiver wire (BOTTOM

LIGHT).

f. Connect the yellow fan wire to the

yellow receiver wire (UPPER

LIGHT).

CAUTION: If your ceiling fan does NOT

have an uplight, there will be NO yellow

fan wire. In this case, cap the yellow

receiver wire using a wire connector

(supplied). If your ceiling fan does NOT

have a downlight, cap the blue receiver

wire using a wire connector (supplied).

BP7270-1 5/6/05 1:29 PM Page 9

28. Insert the connected ends of the wires

up through the open side of the

hanger bracket and into the outlet box

as shown in Figure 16.

29. Screw two 1-1/4” threaded studs

(supplied with the ceiling fan) into the

tapped holes in the hanger bracket

(Figure 16).

30. Slide the receiver up and over the

hanger bracket. Press the receiver

against the ceiling, holding it in place

while installing the ceiling cover in

accordance with the instructions in

the Ceiling Fan Owner’s Manual.

31. Install the fan blades in accordance

with the instructions in the Ceiling Fan

Owner’s Manual.

32. Install the optional Emerson Light

Fixture in accordance with the

instructions in the Light Fixture

Owner’s Manual.

NOTE: To prevent damage to the

receiver, turn “off” the electricity at the

wall switch before installing or

removing light bulbs on the ceiling fan

or light fixture.

OUTLET BOX

RECEIVER

CEILING

COVER

HANGER

BRACKET

1-1/4"

THREADED

STUDS (2)

Figure 16

Operation

IMPORTANT

Fan installation must be completed,

including the installation of the fan

blades, before testing of the remote

control.

Your remote control (Figure 17) has full

control of your fan and lights.

NOTE: Prior to operation of the

downlight from the remote control,

make sure the switch on the light is ON.

1. To set the desired fan speed, press the

HI, MED, or LOW button to operate

your fan on high, medium, or low

speed.

2. To turn your fan off, press the OFF

button.

3. To change the airflow direction of the

fan blades, press the REV button.

4. To turn the downlight on, press and

release the DN button. The light will

turn on at the light intensity previously

selected.

5. To turn the uplight on, press and

release the UP button. The light will

turn on at the light intensity previously

selected.

6. To vary the intensity of the light, hold

the DN or UP button down until the

desired light intensity is reached, then

release the button.

OFF

REV

LOW

MED

HIGH

UP DN

Figure 17

BP7270-1 5/6/05 1:29 PM Page 10

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Emerson Ricevitore

Emerson

Emerson RIDGID FT-103 Manuale utente

Manuali Ricevitore popolari di altre marche

Garmin

Garmin GA 23 Manuale utente

Aiphone

Aiphone PS-12F Manuale utente

IMES

IMES TCS-01CA-PMI Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuale

AMIMON

AMIMON AMN12310 WHDI Manuale utente

Dual

Dual DMCPA79BT Istruzioni operative

Sound Associates

Sound Associates SA652P Manuale utente

Sherwood

Sherwood NewCastle R-772 Manuale utente

Audio

Audio A10-RX Series Manuale utente

AllSee

AllSee PushShare PSRV1.1 Manuale utente

DEMAG

DEMAG DRC-DR D2 Manuale utente

Teleco

Teleco TVRCL868A02 Manuale utente

Bosch

Bosch RF3222E Manuale utente

Kramer

Kramer 631R Manuale utente

Xpress

Xpress xmc10 Manuale utente

JVC

JVC KD-MR1BTS Manuale utente

Omega Engineering

Omega Engineering UWTC-REC3 Manuale utente

e-survey

e-survey E300 Pro Manuale utente