Emerson Rosemount 5408 Manuale utente
Quick Start Guide
00825-0100-4408, Rev AD
March 2018
Rosemount™ 5408 and 5408:SIS Level
Transmitters
Cone Antenna
1 About this guide
This Quick Start Guide provides basic guidelines for the Rosemount 5408 and
5408:SIS Level Transmitters. Refer to the Rosemount 5408 and 5408:SIS
Reference Manual for more instructions. The manual and this guide are also
available electronically on Emerson.com/Rosemount.
WARNING!
Failure to follow safe installation and servicing guidelines could result in
death or serious injury.
•Make sure the transmitter is installed by qualified personnel and in
accordance with applicable code of practice.
•Use the equipment only as specified in this manual. Failure to do so may
impair the protection provided by the equipment.
•For installations in hazardous locations, the transmitter must be installed
according to the Rosemount 5408 and 5408:SIS Product Certifications
document and System Control Drawing (D7000002-885).
Explosions could result in death or serious injury.
•Verify that the operating atmosphere of the transmitter is consistent with
the appropriate hazardous locations certifications.
•Before connecting a Field Communicator in an explosive atmosphere,
ensure the instruments are installed in accordance with intrinsically safe
or non-incendive field wiring practices.
•Do not remove the transmitter cover in explosive atmospheres when the
circuit is live.
•Both transmitter covers must be fully engaged to meet explosion-proof
requirements.
Electrical shock could cause death or serious injury.
•Avoid contact with the leads and terminals. High voltage that may be
present on leads can cause electrical shock.
•Make sure the mains power to the transmitter is off and the lines to any
other external power source are disconnected or not powered while
wiring the transmitter.
Process leaks could result in death or serious injury.
•Make sure that the transmitter is handled carefully. If the process seal is
damaged, gas might escape from the tank.
Quick Start Guide March 2018
2Rosemount 5408 and 5408:SIS Level Transmitters
CAUTION!
Hot surfaces
The flange and process seal may be hot at high process temperatures. Allow
to cool before servicing.
March 2018 Quick Start Guide
Quick Start Guide 3
2 Confirm approval type
For hazardous locations transmitters labeled with multiple approval types:
Permanently mark the checkbox of the selected approval type(s).
Label with Multiple Approval TypesFigure 2-1:
Quick Start Guide March 2018
4Rosemount 5408 and 5408:SIS Level Transmitters
3 Mount the transmitter
3.1 Flanged version
1. If applicable, assemble the segmented cone antenna (see Chapter 9).
2. Lower transmitter with antenna and flange into the nozzle.
Gasket
3. Tighten bolts and nuts with sufficient torque for the flange and gasket
choice.
4. Align the transmitter head (see Chapter 4).
3.2 Flanged version with air purge ring (option code PC1)
1. If applicable, assemble the segmented cone antenna (see Chapter 9).
March 2018 Quick Start Guide
Quick Start Guide 5
2. Place a suitable gasket on the tank flange.
3. Place the purge ring over the gasket.
4. Place a suitable gasket over the purge ring.
Note
A minimum gasket thickness of 0.125 in. (3.2 mm) is required for flanges
with protective plate design.
5. Lower transmitter with antenna and flange into the nozzle.
Quick Start Guide March 2018
6Rosemount 5408 and 5408:SIS Level Transmitters
Antenna with air purge holes
6. Tighten bolts and nuts with sufficient torque for the flange and gasket
choice.
1.0 in. (25.5 mm)
7. Connect the air purging system. Use thread sealant or suitable gasket
according to your site procedures.
March 2018 Quick Start Guide
Quick Start Guide 7
0.4 in. (10 mm)
or
G3/8-in.
Incoming Air Supply SpecificationTable 3-1:
Maximum pressure Recommended pressure
190 psi (13 bar) 100 to 115 psi (7 to 8 bar)
8. Align the transmitter head (see Chapter 4).
3.3 Threaded version, antenna diameter (D) < Thread
diameter (d)
3.3.1 Flanged tank connection
1. If applicable, assemble the segmented cone antenna (see Chapter 9).
2. Place a suitable gasket on the tank flange.
3. Place the customer supplied flange over the gasket.
Quick Start Guide March 2018
8Rosemount 5408 and 5408:SIS Level Transmitters
4. Tighten the bolts and nuts with sufficient torque for the flange and
gasket choice.
5. Apply anti-seize paste or PTFE tape on threads according to your site
procedures.
Gasket may be used as a sealant for adapters with 1½- or 2-in. BSPP
(G) threads.
6. Lower transmitter with antenna and flange into the nozzle.
March 2018 Quick Start Guide
Quick Start Guide 9
Gasket
(for 1½-in. and 2-in.
BSPP (G) threads only)
7. Align the transmitter head (see Chapter 4).
3.3.2 Threaded tank connection
1. If applicable, assemble the segmented cone antenna (see Chapter 9).
2. Apply anti-seize paste or PTFE tape on threads according to your site
procedures.
Gasket may be used as a sealant for adapters with 1½- or 2-in. BSPP
(G) threads.
3. Mount the transmitter on the tank.
Quick Start Guide March 2018
10 Rosemount 5408 and 5408:SIS Level Transmitters
Altri manuali per Rosemount 5408
10
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Emerson Trasmettitore
Emerson
Emerson Rosemount 2088 Manuale utente
Emerson
Emerson PENBERTHY MGT-362 Manuale
Emerson
Emerson Micro Motion 5700 Manuale utente
Emerson
Emerson MICRO MOTION 2700 Manuale del proprietario
Emerson
Emerson Rosemount 8750W Manuale utente
Emerson
Emerson Micro Motion 5700 Manuale utente
Emerson
Emerson Rosemount 648 Manuale utente
Emerson
Emerson Micro Motion 5700 Guida rapida
Emerson
Emerson Rosemount 2051G Manuale utente
Emerson
Emerson Rosemount 3408 Manuale utente
Emerson
Emerson Rosemount 1151 Manuale utente
Emerson
Emerson Rosemount 648 Manuale utente
Emerson
Emerson Rosemount 3308 Manuale utente
Emerson
Emerson Rosemount 248 Manuale utente
Emerson
Emerson Rosemount 3051 Manuale utente
Emerson
Emerson Rosemount 3051 Manuale utente
Emerson
Emerson Rosemount 2051 Manuale utente
Emerson
Emerson Rosemount 5402 Manuale utente
Emerson
Emerson wirelessHART Rosemount Series Manuale utente
Emerson
Emerson Rosemount 2051G Manuale utente
