Emerson Rosemount 644R Manuale utente

Quick Start Guide

00825-0100-4728, Rev DA

June 2016

Rosemount™644H (Device Revision 7 or

Previous) and 644R Smart Temperature

Transmitters

June 2016

Quick Start Guide

NOTICE

This guide provides basic guidelines for the Rosemount 644. It does not provide instructions for detailed

configuration, diagnostics, maintenance, service, troubleshooting, or installation. Refer to the Rosemount

644 Reference Manual for more instruction. The manual and this guide are also available electronically on

EmersonProcess.com/Rosemount.

Explosions could result in death or serious injury.

Installation of this transmitter in an explosive environment must be in accordance with the appropriate local,

national, and international standards, codes, and practices. Review the Product Certifications for any

restrictions associated with a safe installation. In an Explosionproof/Flameproof installation, do not remove

the transmitter covers when power is applied to the unit.

Process leaks may cause harm or result in death.

Install and tighten thermowells or sensors before applying pressure.

Do not remove the thermowell while in operation.

Electrical shock can result in death or serious injury.

Avoid contact with the leads and terminals. High voltage that may be present on leads can cause

electrical shock.

Contents

Configure (bench calibration) . . . . . . . . . . . . . . 3

Verify configuration . . . . . . . . . . . . . . . . . . . . . . 4

Set the switches . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Mount the transmitter . . . . . . . . . . . . . . . . . . . . 8

Wire and apply power . . . . . . . . . . . . . . . . . . . . 12

Perform a loop test . . . . . . . . . . . . . . . . . . . . . . 15

Product Certifications . . . . . . . . . . . . . . . . . . . . 16

Quick Start Guide

June 2016

1.0 Configure (bench calibration)

The Rosemount 644 communicates using the Field Communicator

(communication requires a loop resistance between 250 and 1100 ohms. Do not

operate when power is below 12 Vdc at the transmitter terminal). Refer to the

Rosemount 644 Reference Manual and the Field Communicator Reference

Manual for more information.

1.1 Update the Field Communicator software

The Field Communicator field device revision Dev v6, Device Dashboard (DD) v1

or higher is required for complete functionality. The device will communicate

with all previous Rosemount 644 DD revisions.

Perform the following steps to determine if an upgrade is required.

1. Connect the sensor (see wiring diagram on the inside of housing cover).

2. Connect the bench power supply to the power terminals (“+” or “–”).

3. Connect a Field Communicator to the loop across a loop resistor or at the

power/signal terminals on the transmitter.

4. The following message will appear if the communicator has a previous version

of the device descriptors (DDs).

Upgrade the communicator software to access new XMTR functions. Continue with

old description?

Note

If this notice does not appear, the latest DD is installed. If the latest version is not available,

the communicator will communicate properly. Note that, when the transmitter is

configured to utilize the advanced features of the transmitter (i.e. one of the added sensor

input types), the user will experience trouble communicating and will be prompted to turn

the communicator off. To prevent this from happening, upgrade to the latest DD or answer

NO to the question and default to the generic transmitter functionality.

Figure 1. Connecting a Communicator to a Bench Loop

Rosemount 644 Head Mount Transmitter Rosemount 644 Rail Mount Transmitter

A. 250 Ω≤RL≤1100 Ω

B. AMS™ Device Manager

C. Field Communicator

D. Power supply

June 2016

Quick Start Guide

2.0 Verify configuration

The traditional interface Fast Key sequences in Table 1and Device Dashboard Fast

Key Sequences in Table 2 may be used for transmitter configuration and startup.

2.1 Field Communicator user interface

The Traditional Interface Fast Key Sequences can be found on Table 1 on page 5.

Figure 2. Traditional Interface

The Device Dashboard Fast Key Sequence can be found on Table 2 on page 6.

Figure 3. Device Dashboard

Quick Start Guide

June 2016

Table 1. Traditional Interface Fast Key Sequences

Function Fast Keys Function Fast Keys

Active Calibrator 1, 2, 2, 1, 3 Open Sensor Holdoff 1, 3, 5, 3

Alarm/Saturation 1, 3, 3, 2 Percent Range 1, 1, 5

AO Alarm Type 1, 3, 3, 2, 1 Poll Address 1, 3, 3, 3, 1

Burst Mode 1, 3, 3, 3, 3 Process Temperature 1, 1

Burst Option 1, 3, 3, 3, 4 Process Variables 1, 1

Calibration 1, 2, 2 PV Damping 1, 3, 3, 1, 3

Callendar-Van Dusen 1, 3, 2, 1 PV Unit 1, 3, 3, 1, 4

Configuration 1, 3 Range Values 1, 3, 3, 1

D/A Trim 1, 2, 2, 2 Review 1, 4

Damping Values 1, 1, 10 Scaled D/A Trim 1, 2, 2, 3

Date 1, 3, 4, 2 Sensor Connection 1, 3, 2, 1, 1

Descriptor 1, 3, 4, 3 Sensor 1 Setup 1, 3, 2, 1, 2

Device Info 1, 3, 4 Sensor Serial Number 1, 3, 2, 1, 4

Device Output Configuration 1, 3, 3 Sensor 1 Trim 1, 2, 2, 1

Diagnostics and Service 1, 2 Sensor 1 Trim-Factory 1, 2, 2, 1, 2

Filter 50/60 Hz 1, 3, 5, 1 Sensor Type 1, 3, 2, 1, 1

Hardware Rev 1, 4, 1 Software Revision 1, 4, 1

Hart Output 1, 3, 3, 3 Status 1, 2, 1, 4

Intermittent Detect 1, 3, 5, 4 Tag 1, 3, 4, 1

LCD Display Options 1, 3, 3, 4 Terminal Temperature 1, 3, 2, 2

Loop Test 1, 2, 1, 1 Test Device 1, 2, 1

LRV (Lower Range Value) 1, 1, 6 URV (Upper Range Value) 1, 1, 7

LSL (Lower Sensor Limit) 1, 1, 8 USL (Upper Sensor Limit) 1, 1, 9

Measurement Filtering 1, 3, 5 Variable Mapping 1, 3, 1

Message 1, 3, 4, 4 Variable Re-Map 1, 3, 1, 5

Meter Configuring 1, 3, 3, 4, 1 Write Protect 1, 2, 3

Meter Decimal Point 1, 3, 3, 4, 2 2-Wire Offset 1, 3, 2, 1, 2, 1

Num Req Preams 1, 3, 3, 3, 2

June 2016

Quick Start Guide

2.2 Input/verify Callendar Van-Dusen constants

If sensor matching is being used with this combination of a transmitter and

sensor, verify the constants input.

1. From the Home screen, select 1 Device Setup, 3 Configuration, 2 Sensor

Config, 1 Sensor 1, 3 Cal Van-Dusen. Set the control loop to manual. Select

OK.

2. At the Enter Sensor Type prompt, select Cal Van-Dusen.

3. At the Enter Sensor Connection prompt, select the appropriate number of

wires.

4. Enter the Ro, Alpha, Beta, and Delta values from the stainless steel tag

attached to the special-order sensor.

5. Select OK after you return the control loop to automatic control.

Table 2. Device Dashboard Fast Key Sequences

Function Fast Keys Function Fast Keys

Active Calibrator 2, 2, 4, 2 Num Req Preams 2, 2, 5, 2

Alarm/Saturation 2, 2, 2, 6 Open Sensor Holdoff 2, 2, 4, 4

Burst Mode 2, 2, 5, 3 Percent Range 2, 2, 2, 4

Burst Option 2, 2, 5, 4 Poll Address 2, 2, 5, 1

Calibration 2, 1, 2 PV Damping 2, 2, 1, 6

Callendar-Van Dusen 2, 2, 1, 10 PV Unit 2, 2, 1, 4

Configuration 2, 1, 1 Range Values 2, 2, 2, 5

D/A Trim 3, 4, 2 Scaled D/A Trim 3, 4, 3

Damping Values 2, 2, 1, 6 Sensor Connection 2, 2, 1, 3

Date 1, 7, 8 Sensor 1 Setup 2, 2, 1

Descriptor 1, 7, 6 Sensor Serial Number 2, 2, 1, 7

Device Info 1, 7 Sensor 1 Trim 3, 4, 1

Device Output Configuration 2, 2, 2 Sensor 1 Trim-Factory 3, 4, 1, 2

Filter 50/60 Hz 2, 2, 4, 7, 1 Sensor Type 2, 2, 1, 2

Hardware Rev 1, 7, 9, 3 Software Revision 1, 7, 9, 4

Hart Output 2, 2, 5 Tag 2, 2, 4, 1, 1

LCD Display Options 2, 2, 3 Terminal Temperature 3, 3, 2

Loop Test 3, 5, 1 URV (Upper Range Value) 2, 2, 2, 5, 2

LRV (Lower Range Value) 2, 2, 2, 5, 3 USL (Upper Sensor Limit) 2, 2, 1, 8

LSL (Lower Sensor Limit) 2, 2, 1, 9 Variable Mapping 2, 2, 5, 5

Message 1, 7, 7 Variable Re-Map 2, 2, 5, 5, 5

Meter Configuring 2, 2, 3, 1 Write Protect 2, 2, 4, 6

Meter Decimal Point 2, 2, 3, 2 2-Wire Offset 2, 2, 1, 5

Quick Start Guide

June 2016

2.3 Input/verify Callendar Van-Dusen constants

If sensor matching is being used with this combination of a transmitter and

sensor, verify the constants input.

1. From the Home screen, select 2 Configure, 2 Manual Setup, 1 Sensor. Set the

control loop to manual and select OK.

2. At the Enter Sensor Type prompt, select Cal VanDusen.

3. At the Enter Sensor Connection, select the appropriate number of wires

prompt.

4. Enter the Ro, Alpha, Delta, and Beta values from the stainless steel tag

attached to the special-order sensor when prompted.

5. Return the control loop to automatic control and select OK.

6. To disable the transmitter-sensor matching feature from the Home screen

select 2 Configure, 2 Manual Setup, 1 Sensor, 10 SensorMatching-CVD. At

the Enter Sensor Type prompt, select the appropriate sensor type.

3.0 Set the switches

3.1 Rosemount 644H (switch on bottom right of electronics

module)

Without an LCD display

1. Set the loop to manual (if applicable) and disconnect the power.

2. Remove the electronics housing cover.

3. Set the switch to the desired position. Replace housing cover.

4. Apply power and set the loop to automatic control.

With an LCD display (Rosemount 644H only)

1. Set the loop to manual (if applicable) and disconnect the power.

2. Remove the electronics housing cover.

3. Snap-off the LCD display straight off.

4. Set the switch to the desired position.

5. Reattach the LCD display and electronics housing cover (consider LCD display

orientation – rotate in 90°increments).

6. Apply power and set the loop to automatic control.

3.2 Rosemount 644R (switch on middle of front panel)

1. Open the front door of the Rosemount 644R Rail Mount Transmitter.

2. Set the switch to the desired position.

June 2016

Quick Start Guide

4.0 Mount the transmitter

Mount the transmitter at a high point in the conduit run to prevent moisture from

draining into the transmitter housing.

4.1 Typical connection head installation

Head mount transmitter with DIN plate style sensor

1. Attach the thermowell to the pipe or process container wall. Install and

tighten the thermowell before applying process pressure.

2. Verify the transmitter failure mode switch.

3. Assemble the transmitter to the sensor. Push the transmitter mounting

screws through the sensor mounting plate and insert the snap rings (optional)

into the transmitter mounting screw groove.

4. Wire the sensor to the transmitter (see “Wire and apply power” on page 12 for

more information).

5. Insert the transmitter-sensor assembly into the connection head. Thread the

transmitter mounting screw into the connection head mounting holes.

Assemble the extension to the connection head. Insert the assembly into the

thermowell.

6. Slip the shielded cable though the cable gland.

7. Attach a cable gland into the shielded cable.

8. Insert the shielded cable leads into the connection head through the cable

entry. Connect and tighten the cable gland.

9. Connect the shielded power cable leads to the transmitter power terminals.

Avoid contact with sensor leads and sensor connections.

10. Install and tighten the connection head cover. Enclosure covers must be fully

engaged to meet explosion-proof requirements.

A. Rosemount 644H Transmitter D. Transmitter mounting screws

B. Connection head E. Integral mount sensor with flying leads

C. Thermowell F. Ex tension

Quick Start Guide

June 2016

4.2 Typical universal head installation

Head mount transmitter with threaded sensor

1. Attach the thermowell to the pipe or process container wall. Install and

tighten thermowells before applying process pressure.

2. Attach necessary extension nipples and adapters to the thermowell. Seal the

nipple and adapter threads with silicone tape.

3. Screw the sensor into the thermowell. Install drain seals if required for severe

environments or to satisfy code requirements.

4. Verify the transmitter failure mode switch.

5. Pull the sensor wiring leads through the universal head and transmitter.

Mount the transmitter in the universal head by threading the transmitter

mounting screws into the universal head mounting holes.

6. Mount the transmitter-sensor assembly into the thermowell. Seal adapter

threads with silicone tape.

7. Install conduit for field wiring to the conduit entry of the universal head. Seal

conduit threads with silicone tape.

8. Pull the field wiring leads through the conduit into the universal head. Attach

the sensor and power leads to the transmitter. Avoid contact with other

terminals.

9. Install and tighten the universal head cover. Enclosure covers must be fully

engaged to meet explosion-proof requirements.

A. Threaded thermowell D. Universal head (transmitter inside)

B. Standard extension E. Conduit entry

C. Threaded style sensor

ABCD

June 2016

Quick Start Guide

4.3 Rail mount transmitter and sensor

1. Attach the transmitter to a suitable rail or panel.

2. Attach the thermowell to the pipe or process container wall. Install and

tighten the thermowell, according to plant standards, before applying

pressure.

3. Attach the sensor to the connection head and mount the entire assembly to

the thermowell.

4. Attach and connect sufficient lengths of sensor lead wire from the connection

head to the sensor terminal block.

5. Tighten the connection head cover. Enclosure covers must be fully engaged to

meet explosion-proof requirements.

6. Run sensor lead wires from the sensor assembly to the transmitter.

7. Verify the transmitter failure mode switch.

8. Attach the sensor wires to the transmitter (see “Wire and apply power” on

page 12 for more information).

A. Rail mount transmitter D. Connection head

B. Sensor leads with cable glands E. Standard extension

C. Integral mount sensor with terminal block F. Threaded thermowell

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Emerson Trasmettitore

Emerson

Emerson Rosemount 8732E Manuale utente

Emerson

Emerson Rosemount Analytical HART SMART 5081C-HT Manuale utente

Emerson

Emerson Rosemount 644h Manuale utente

Emerson

Emerson Net Safety Millennium II Manuale utente

Emerson

Emerson MAS 2600 Manuale utente

Emerson

Emerson Rosemount 1057 Manuale utente

Emerson

Emerson Rosemount 550PT Manuale utente

Emerson

Emerson Micro Motion 2500 Guida rapida

Emerson

Emerson Rosemount 5408 Manuale utente

Emerson

Emerson Rosemount 2090 Guida alla configurazione

Emerson

Emerson Rosemount 3095 Manuale utente

Emerson

Emerson Rosemount 644h Manuale utente

Emerson

Emerson Rosemount 2051 Manuale utente

Emerson

Emerson Rosemount 3144P Manuale utente

Emerson

Emerson Rosemount 248 Manuale utente

Emerson

Emerson wirelessHART Rosemount Series Manuale utente

Emerson

Emerson Rosemount MultiVariable 3051SMV Manuale utente

Emerson

Emerson Rosemount 644 Manuale utente

Emerson

Emerson Rosemount 6888A Manuale utente

Emerson

Emerson Rosemount 5408 Manuale utente

Emerson

Emerson Rosemount CX1100 Manuale utente

Emerson

Emerson Rosemount 1199 Manuale utente

Emerson

Emerson Rosemount 3051 Manuale utente

Emerson

Emerson Rosemount 1151 Manuale utente

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente