Emerson Rosemount Wireless Permasense WT210 Manuale utente
Quick Start Guide
MS-00825-0300-4210, Rev AA
October2023
Universal Mount for Rosemount™
Wireless WT210 Corrosion
Transmitters
Contents
Universal Mount for Rosemount Wireless WT210 Corrosion Transmitters......................... 3
Overview....................................................................................................................................... 4
Strap mount installation............................................................................................................. 6
Rosemount Wireless WT210 Corrosion Transmitter Installation........................................ 17
Quick Start Guide October2023
2 Emerson.com/Rosemount
1 Universal Mount for Rosemount Wireless
WT210 Corrosion Transmitters
Universal Mount for Rosemount Wireless WT210 Corrosion
Transmitters is a device that mounts one sensor on pipe diameters of
NPS 4 to NPS 20 (DN 100 to DN 500). Universal Mount for Rosemount
Wireless WT210 Corrosion Transmitters are designed to optimize
the ultrasonic performance of the sensors that are attached with
it. The key to achieving high performance is to deliver constant
coupling pressure for the ultrasonic sensors and the pipe. The strap
and spring assembly of these mounts are engineered to deliver
consistent performance at a wide range of temperatures.
NOTICE
This guide provides basic guidelines for the installation of the
Universal Mount for Rosemount Wireless WT210 Corrosion
Transmitters. It does not provide instructions for installing
Rosemount Wireless WT210 Corrosion Transmitters, for the
installation of Rosemount Wireless WT210 Corrosion Transmitters
please refer to Rosemount WT210 Wireless Corrosion Transmitter
Quick Start Guide. This guide is also available electronically on
Emerson.com\Rosemount.
WARNING
Rosemount Wireless Permasense WT210 Wireless corrosion
transmitters should only be mounted on approved mounting
solutions by persons who are trained in the safe and correct
installation procedures.
WARNING
Physical access
Unauthorized personnel may potentially cause significant damage to
and/or misconfiguration of end users’ equipment. This could be
intentional or unintentional and needs to be protected against.
Physical security is an important part of any security program and
fundamental in protecting your system. Restrict physical access by
unauthorized personnel to protect end users’ assets. This is true for
all systems used within the facility.
October2023 Quick Start Guide
Quick Start Guide 3
2 Overview
Figure 2-1: Universal Mount Overview
Sensor Bed Assembly
A. Strap
B. Strap holder
C. Strap hold plate
D. M6 strap hold plate bolts
E. M8 strap tensioner bolts and disc springs
F. M8 studs with M8 nuts & M8 nord lock washers
G. Lanyard slot (one on each corner of sensor bed assembly)
H. Sliders
2.1 What's in the box
•Sensor Bed assembly
•Strap (1580 mm [5 ft.])
•M8 Nord lock washer (fitted on the studs)
•M8 Nut (fitted on the studs)
Quick Start Guide October2023
4 Emerson.com/Rosemount
•Two stainless steel safety lanyards
•4 x M6 dome nuts, 4 x M6 washer and 4 x M6 x 18mm
countersunk screws (for use with NPS 4–6” pipe, see Pre-
installation)
•2 x Spare M6 strap hold plate bolts (M6 x 14 hex head bolts and 2
x M6 nord locks
2.2 Clamp identification
Part number, weight, country of origin, and read instructions symbol
are displayed on the product label.
Figure 2-2: Product markings
2.3 Required equipment
The equipment for clamp installation is supplied in Rosemount
IK220 Installation Kit for Rosemount Wireless Permasense Corrosion
Transmitters.
•Torque wrench, 3/8-in. drive (2–24 Nm range)
•13 mm socket, 3/8-in. drive
•10 mm socket, 3/8-in. drive
•4 mm hex key
•Loctite 8009 anti-seize compound
•Tin snips
•Strap mount holder (recommended)
October2023 Quick Start Guide
Quick Start Guide 5
3 Strap mount installation
3.1 Pre-installation
The following steps can be completed prior to installing at the asset,
this is to limit the installation team exposure to the high temperature
the asset could be running at.
WARNING
Personal protective equipment (PPE) of gloves and safety glasses or
full-face visor are recommended.
Cut strap may have sharp edges.
Note
Step 1 is for 4-in. pipe only, for all other pipe diameters skip to step 2.
1. If installation is on a 4-in. pipe elbow, the 4 x M6 cap nuts, 4 x
M6 Nord locks & M6 x 16 mm countersunk screws need to be
replaced.
For 4-in. pipe elbows (long radius NPS/DN), replace 4 x M6 cap
nuts, 4 x M6 Nord locks and M6 x 16 mm countersunk screws
with 4 x M6 dome nuts, 4 x M6 washers, 4 x M6 Nord locks and
4 x M6 x 20 mm countersunk screws provided in the Universal
Mount box.
Quick Start Guide October2023
6 Emerson.com/Rosemount
4–6-in. elbow
a. M6 x 20 mm countersunk screw (already fitted to sensor
bed assembly)
b. M6 dome nut
c. M6 washer
d. M6 Nord lock washer
Use 10 A/F socket with 2–24 Nm torque wrench and 4 mm hex
key provided. Torque dome nuts to 10 Nm.
2. If pipe is to be installed on an NPS/DN straight pipe or NPS/DN
long radius elbow, it is recommended to cut strap prior to
installation. If the pipe is a non-standard size then size and cut
strap to length as per section Strap mount installation, step 4.
Total strap length provided is 1580 mm. Cut to the following
lengths based on pipe diameter.
Note
Even though the strap can be pre-cut before mounting to
match the asset diameter, there may be a need to adjust
strapping once mounted on the asset.
NPS DN Strap length
(mm)
Strap length
(in.)
4 100 410 16.14
6 150 560 22.05
8 200 710 27.95
10 250 875 32.09
12 300 1025 40.35
14 350 1115 43.90
16 400 1280 50.39
October2023 Quick Start Guide
Quick Start Guide 7
NPS DN Strap length
(mm)
Strap length
(in.)
18 150 1430 56.30
20 500 No cutting required
Example shown below is for a NPS 14” (DN 350) pipe.
Measure & Cut (with tinsnips):
Cut across bottom of hole closest to measurement.
Note
It is recommended that one side of the Strap is secured to the
mount prior to placing the mount on the asset. This will make
the full installation easier once the mount has been placed on
the asset.
3. Loosen the 2 x m6 bolts in the Strap Holder using the 10 mm
socket such that they cannot be seen or felt behind the Strap
Holder. These bolts do not have to be removed fully to slide
the Strap into the Strap Holder.
Quick Start Guide October2023
8 Emerson.com/Rosemount
Section view of Universal Mount showing bolt position in strap
holder.
4. Take one end of the strap and load it into a strap holder
on the sensor bed assembly ensuring that the 3 pins of the
strap holder fully engage with 3 holes of the strap. Push down
the hold plate and torque each bolt to 10 Nm using the 10
mm socket and torque wrench. Once the last bolt has been
torqued to 10Nm, check the first other bolts to ensure they are
still torqued to at least 10Nm.
Hold plate is transparent in image on left.
5. Fit Universal Mount holder and torque M8 stud nuts of the
sensor bed assembly to 10 Nm.
October2023 Quick Start Guide
Quick Start Guide 9
Note
Use of Universal Mount Holder and pre-cutting Strap to length
are recommended for ‘hot pipe' installations in particular.
3.2 Surface preparation
On painted pipework, remove a singular patch of the coating about
1-in. (25 mm) diameter in the location you wish to monitor to allow
waveguides to contact pipe directly.
3.3 Strap mount installation
WARNING
Two people are required for this operation
Personal protective equipment (PPE) of gloves and safety glasses or
full-face visor are recommended.
Cut strap may have sharp edges.
DO NOT cut the strap while it is under tension because this action
can result in injury or damage.
Before placing the device onto the mounting surface (asset), ensure
that the safety lanyards which are provided are attached and secured
to prevent the device falling from heights potentially causing injury.
Quick Start Guide October2023
10 Emerson.com/Rosemount
Altri manuali per Rosemount Wireless Permasense WT210
2
Indice
Altri manuali Emerson Trasmettitore
Emerson
Emerson Rosemount 5408 Manuale utente
Emerson
Emerson Micro Motion 5700 Manuale utente
Emerson
Emerson Rosemount 848T Manuale utente
Emerson
Emerson Rosemount 3144P Manuale utente
Emerson
Emerson Rosemount 3051G Manuale utente
Emerson
Emerson PENBERTHY MGT-362 Manuale
Emerson
Emerson Micro Motion ELITE Manuale utente
Emerson
Emerson Rosemount 2051 Wireless Series Manuale utente
Emerson
Emerson Micro Motion 2400S Guida rapida
Emerson
Emerson Micro Motion 2400S Manuale utente
Emerson
Emerson Rosemount 3051HT Manuale utente
Emerson
Emerson Rosemount ET410 Manuale utente
Emerson
Emerson Rosemount 3051 CF Series Manuale utente
Emerson
Emerson Rosemount 6888A Manuale utente
Emerson
Emerson Rosemount 3051 Manuale utente
Emerson
Emerson Rosemount 5081 Manuale utente
Emerson
Emerson Rosemount 248 Manuale utente
Emerson
Emerson Rosemount 702 Manuale utente
Emerson
Emerson Fisher FIELDVUE 4400 Manuale utente
Emerson
Emerson Rosemount 3095FC MultiVariable Manuale utente
