Endeavor Entone Manuale utente

2 S. West Street • P.O. Box 237

Cloverdale, IN 46120

Voice • 765.795.4261 • 800.922.6677

Fax • 765.795.6599

www.weEndeavor.com

Updated 9/1/15

To Program Remote to Control Your TV or AUX Device:

1. Locate the device code for your desired device in the device

code table provided at

www.weEndeavor.com/remotecodes

If you cannot ﬁnd the device code for your device or it does not

work after trying the listed device codes for your device brand,

then you can try the auto search at the end of this section.

2. Turn on your device and with media inserted (if applicable).

3. On the remote control, press a device mode key for 5 seconds

(i.e.,

AUX

). The device mode key will light up.

NOTE: Use the “AUX” mode key for a VCR, DVD player, cable

box, satellite receiver or audio device.

4. Enter the four-digit device code for your device. Device codes

can be found at

www.weEndeavor.com/remotecodes

. If you

perform this procedure correctly, the selected device mode key

backlight will blink twice.

5. Aim the remote control at your device and press

POWER

once.

The device should turn off. If it does not respond, repeat the

above steps.

NOTE: While in programming mode, if no key is received within

30 seconds or an invalid device code is entered, the device mode key

backlight will blink rapidly 7 times and then stop - indicating an error.

Programming Your Entone Remote Control

Navigate Favorites on the GUIDE

A FAVORITES LIST allows you to select channels you watch most often, placing

them on a list that is quickly accessed in the GUIDE.

You can continue to press the GUIDE key on your remote control to toggle

between any saved FAVORITES such as

All, Subscribed, HD, PPV

and any

other FAVORITES LISTS you create.

NOTE: You can toggle between all

FAVORITES by continuing to press

the GUIDE key on your remote

control.

Entone Remote

UE Titan Remote

Entone Nova

Remote

12 1

Your Set Top Box & DVR

1. eSATA:

Connects the set top box to an external DVR storage device.

2. CABLE/ANT IN:

Connects the set top box to a wall jack using coax cable to provide

video service.

3. TV Out:

Connects the set top box to your TV using a standard coax cable - provides

audio and video.

4. VIDEO:

Connects the set top box to provide good quality video - provides video only.

5. AUDIO LEFT/RIGHT:

Connects the set top box to provide stereo audio - provides

audio only.

6. COMPONENT (HD Analog) OUTPUT:

(Video/Audio Left/Audio Right) Connects the

set top box to your TV or VCR to provide high deﬁnition quality analog video and

stereo audio.

7. DIGITAL AUDIO (S/PDIF):

Connects the set top box to a home theater system via

ﬁber optic cable for best quality audio - provides audio only.

8. HDMI:

(High Deﬁnition Media Interface) Connects the set top box to your HDTV

using an HDMI cable - provides audio and video.

9. USB:

(Universal Serial Bus) Connects the set top box to technician’s equipment and

other devices.

10. Power Adapter:

Provides power to the set top box.

11. Ethernet:

Connects the set top box to the video service using a CAT5 E

thernet cable

Entone 455 Set Top Box

Entone 455 Set Top B

(Expanded Services Console ADB 5810)

Your Entone Remote Control at a Glance

Pressing the TV Button

tells remote to control the TV

Pressing the STB Button

tells remote to control

the Set Top Box

Power

Turns on or off device selected.

Device Control Buttons

Selects the device you wish to control.

Example - the STB button allows

your remote to control the functions

of your Set Top Box.

AUX button controls functions on DVD

or other device.

Playback Controls

REPLAY:

goes back approx. 7 seco

ond

REW/FF:

rewinds/fast forwards vid

eo (press

repeatedly to increase speed 4x, 15

5x, 60x, 30

0x)

SKIP:

advances ahead in 30 secon

d i

ncr

eme

nts

REC:

starts or stops recording a pr

rogram.

PAUSE:

pauses video.

PLAY:

plays video or resumes paus

sed program.

STOP:

stops playback of video.

Movies on Demand

Exit

Exits out of current menu item.

Guide

Controls the on-screen

program guide.

Displays on-screen menu.

Navigation

ARROW KEYS:

navigates up, dow

left

and right on on-screen guide or me

enus.

OK:

selects option that is highlighte

ed.

Info

Shows on-screen information

for selected program.

VOL +/-

Turns volume on or off.

Mute Button

Turns sound on and off of selected

evi

ce.

INPUT

Changes current AV input of select

ted

device programmed.

ivates Set Top Box closed captioning.

Act

NOTE - The default code for

Parental Controls is “0”

CH/PG up/down

Controls your channel or page

selections up or down.

INFO BAR is displayed

when channels are selected.

Last

Moves back to previous channel.

Number Buttons

Enters channel numbers, device

setup codes and PIN numbers.

INFO BAR is displayed

when channels are selected.

Options

Provides additional options for certa

ain

on-screen menu items.

Back

Return to the previous selection.

Visit www.weEndeavor.com/television/tv support for

additional instructions and remote control programming de-

vice codes for the Entone remote.

DVR Control

211

STEP 1 - Turn ON or OFF your TV

Press the TV button ONCE

(The TV button will

light up red

when pressed

and will go off when released)

Press the Power button ONCE

(The TV turns on. Pressing Power button

again turns TV off)

You don’t need to press TV button to change

channels or control the TV volume!

IMPORTANT - YOUR TV MUST BE SET TO CHANNEL __________

TO BE ABLE TO RECEIVE ENDEAVOR CHANNELS

STEP 2 - Turn ON Set Top Box (STB)

Press the STB button ONCE

(The STB button will

light up red

when pressed

and will go off when released)

Press the Power button ONCE

(The STB turns on. The BLUE POWER

LIGHT will be illuminated. If this light is

GRAY, repeat above step)

After pressing the STB button you can:

> Adjust the channels up or down

> Access the GUIDE, MENU and INFO

> Adjust the volume up or down

Quick Start Guide to Using

STEP 3 - Navigate the Channels

You may change channels three ways:

Pressing the Number buttons

Pressing the Channel up/down buttons

(HINT: When pressing Number and Channel up/down buttons,

the INFO BAR is displayed at bottom of screen. The

INFO BAR gives information about the current channel)

Making channel selections using the GUIDE

STEP 4 - Navigate the Guide

Press the GUIDE button ONCE

(HINT: You must press the STB button FIRST,

then GUIDE)

The GUIDE screen appears. Channel

selections are now shown 7 at a time

at the bottom of the screen.

To select a channel from the GUIDE:

> Press Directional Arrow buttons

This scrolls through each channel

> Press OK button to make channel selection

(HINT: to bring up the next or previous 7

channel entries, Press the Channel up/down buttons)

> Press EXIT button once and the GUIDE will disappear from screen

Device Control Button -

Press device buttons ONCE to

activate other entertainment devices such as a DVD

Player.

(You will need to use the remote control from

your external device thereafter if you don’t program

your device with the entone remote).

Your

Remote Control

STEP 3 - Navigate the Channels

You may change channels three ways:

Pressing the Number buttons

Pressing the Channel up/down buttons

(HINT: When pressing Number and Channel up/down buttons,

the INFO BAR is displayed at bottom of screen. The

INFO BAR gives information about the current channel)

Making channel selections using the GUIDE

STEP 4 - Navigate the Guide

Press the GUIDE button ONCE

(HINT: You must press the STB button FIRST,

then GUIDE)

The GUIDE screen appears. Channel

selections are now shown 7 at a time

at the bottom of the screen.

To select a channel from the GUIDE:

> Press Directional Arrow buttons

This scrolls through each channel

> Press OK button to make channel selection

(HINT: to bring up the next or previous 7

channel entries, Press the Channel up/down buttons)

> Press EXIT button once and the GUIDE will disappear from screen

Device Control Button -

Press device buttons ONCE to

activate other entertainment devices such as a DVD

Player.

(You will need to use the remote control from

your external device thereafter if you don’t program

your device with the entone remote).

STEP 1 - Turn ON or OFF your TV

Press the TV button ONCE

(The TV button will

light up red

when pressed

and will go off when released)

Press the Power button ONCE

(The TV turns on. Pressing Power button

again turns TV off)

You don’t need to press TV button to change

channels or control the TV volume!

IMPORTANT - YOUR TV MUST BE SET TO CHANNEL __________

TO BE ABLE TO RECEIVE ENDEAVOR CHANNELS

> Select ON DEMAND>RENTALS to

select and purchase a VOD movie

STEP 2 - Turn ON Set Top Box (STB)

Press the STB button ONCE

(The STB button will

light up red

when pressed

and will go off when released)

Press the Power button ONCE

(The STB turns on. The BLUE POWER

LIGHT will be illuminated. If this light is

GRAY, repeat above step)

After pressing the STB button you can:

> Adjust the channels up or down

> Access the GUIDE, MENU and INFO

> Adjust the volume up or down

Quick Start Guide to Using Your

Remote Control

Programming Your UE Titan Remote Control

To Program Devices with Your UE Titan Remote:

The Titan universal remote control comes pre-programmed to operate the

set-top box that is supplied by your service provider. In addition, the Titan

can be programmed to control four (4) additional home theater equipment

devices.

NOTE:

If you have another brand of set-top box that you wish to control

with the STB key, you’ll need to refer to “Re-Programming Set-Top Box

Control”.

1. Turn on all of the devices that you wish to control.

2. On the remote control, press the mode key that you wish to program

once (AUX, DVD, AUD,or TV); it blinks once.

3. Press and hold SETUP until the mode LED blinks twice.

4. Search for the “Manufacturer’s Codes” in the lookup below for the

device you wish to control. Enter the ﬁrst ﬁve-digit code for your

device. If performed correctly, the mode LED blinks twice.

NOTE:

If the selected mode LED emits a long blink, the entry is invalid.

Repeat steps 2 through 4 and try entering the same code again.

5. Aim the remote control at the device and press POWER once. The de-

vice should turn off. If it does not, repeat steps 2 through 3, trying each

code for your brand until you ﬁnd one that works. If it still does not

respond, try searching for the code (“Searching for Your Code”).

NOTE:

If the device does not have a POWER key, press the (Play) key.

Repeat steps 2 through 5 for another mode and/or key or press and

hold SETUP to exit programming. TV Code

Please use manual for device code selection

Your

Remote Control at a Glance

NOTE - The default code for

Parental Controls is “0”

Visit www.weEndeavor.com/television/tv support

for additional instructions and remote control programming device

codes for the Entone Nova remote.

Pressing the TV Button

tells remote to control the TV

Pressing the STB Button

tells remote to control

the Set Top Box

Power

Turn

ns on or off device selected.

Set Up

ote for TV.

Set

up re

Transport Buttons

Contr

rols video program for LIVE TV/DVR/VOD

REPL

LAY

Goes back approx. 30 seconds.

REW

winds video.

FF:

Fast forwards vid

eo.

SKIP

Adv

ances ahead in 30 second incremen

ts.

PAUS

SE:

uses vide

PLAY

ays video or resumes a paused program.

STOP

Stops playback of video.

Info

about the

Displays on-screen information a

program.

cur

rent TV/VOD/DVR

Displa

ays on-screen menu.

Navigation

ARR

OW KEYS:

Navigates

e/menus.

wit

hin

the on-screen

gui

OK:

nu option.

Exe

cut

es the currently selected men

LEF

T/RIGHT:

rds video.

Rew

ind

s/Fast forwa

Rec

program.

Sto

ps or starts recordin

g a

Mute

Turns

vol

ume on/off.

Options

Provid

es additional options for certain

on-sc

creen menu ite

ms.

Last

Chang

s channel to the previously viewed

chann

TV/Input

Chan

nges current A/V input of selecte

devic

ce programmed (i.e. TV or AUX).

Device Control

to control.

Sel

ects the device you wish

TV:

ontrol TV

Sel

ect

STB

ogrammed

This button is pre-p

ne device.

to control the

Ent

DVD

grammed).

Select to control DVD (if prog

AUX

her device

Select to control

ano

grammed).

(if

prog

Back

Goes

s back one level within men

us.

Guide

n-screen

Controls

the

am guide.

pro

gra

CH/PG

up/down

Cha

nges channel up/down or pages

m guide.

within the on-screen program

Number Buttons

hannels

All

ows

rect access to speciﬁc c

u items.

and

VOD

Endeavor

Fea

ture provides access to

ramming.

VOD

progr

Exit

Exits

the current menu item or

LIVE

A, B, C, D

ture use.

For

Vol +/-

Increa

ases or decreases TV volume.

Dot

For fut

ture u

se.

DVR

Featur

e prov

ide

s access to Endeavor DVR

g on/off.

Toggles closed captionin

Media & Live TV

For future use.

NOTE - The default code for

Parental Controls is “0”

NOT

E -

The d

efa

ult

for

ParPar

Par

ent

ConCon

Con

trotro

tro

“0”“0”

“0”

Programming Your Entone Nova Remote Control

To Program Devices with Your Entone Nova Remote:

1. Locate the device code for your device in the Device Codes table provided on the

Entone Remote Control Reference Guide at

https://www.weendeavor.com/

wp-content/uploads/Nova-Remote-Quick-Reference-Guide.pdf

. If you cannot

ﬁnd the device code for your device or it does not work after trying the listed device

codes for your device brand, then you can try the auto search on page 7 of the

online Entone Remote Control Reference guide.

2. Turn on your device.

3. On the remote control, press the Device Control key (TV/STB/DVD/ AUX) to

choose the device mode.

4. Press the “SETUP” key and the LED blinks twice.

5. Enter the ﬁve-digit device code for your device. If you perform this procdure

correctly, the LED will blink twice.

Otherwise, it has a long blink.

6. Press “Power” key. If your device turns off, setup is complete.

7. If your device does not turn off, repeat this procedure using the next code for your

device brand.

Please use the Entone Nova Remote Control Reference Guide for device code activa-

tion by visiting

https://www.weendeavor.com/wp-content/uploads/Nova-Remote-

Quick- Reference-Guide.pdf

Your UE Remote Control at a Glance

Pressing the TV Button

tells remote to control the TV

Pressing the STB Button

tells remote to control

the Set Top Box

Setup

Controls all device programming

sequences.

Entertainment Device Keys

Selects the device you wish to control.

Example - the STB button allows

your remote to control the functions

of your Set Top Box.

Power

Turns on or off device selected.

Skip Back

Allows DVR instant replay of the

last 7 seconds of program that

you were watching.

List

Pressing LIST>PVR accesses

your DVR functionality.

Exit

Exits out of current screen

selection including the on-screen

program guide.

Device Controls

Controls DVR and other

programmable devices

such as a DVD player.

Guide

Controls the on-screen

program guide.

Brings up menu of devices

you are controlling.

Directional Arrows

Navigates through menu of selected

device such as the on-screen

program guide. OK veriﬁes selection.

Info

Provides program information

for selected channel.

Page +/-

Navigates up or down through

menu screens and program guide.

Volume +/-

Controls volume level of your device

up or down.

Mute Button

Turns sound off and on.

Keypad Numbers

Enters channel numbers and device

setup codes. INFO BAR is displayed

when channels are selected.

Activates Set Top Box closed captioning.

Last

Moves back to previous channel.

On Demand

Pressing ON DEMAND>RENTALS

allows selection and purchase

of VOD movie rental.

A, B, C, D

For future use.

CH +/-

Controls your channel

selections up or down.

INFO BAR is displayed

when channels are selected.

STEP 3 - Navigate the Channels

You may change channels three ways:

Pressing the Number buttons

Pressing the Channel +/- buttons

(HINT: When pressing Number and Channel +/- buttons,

the INFO BAR is displayed at bottom of screen. The

INFO BAR gives information about the current channel)

Making channel selections using the GUIDE

STEP 4 - Navigate the Guide

Press the GUIDE button ONCE

(HINT: You must press the STB button FIRST,

then GUIDE)

The GUIDE screen appears. Channel

selections are now shown 5 at a time

at the bottom of the screen.

To select a channel from the GUIDE:

> Press Directional Arrow buttons +/-

This scrolls through each channel

> Press OK button to make channel selection

(HINT: to bring up the next or previous 5

channel entries, Press the Channel +/- buttons)

> Press OK button twice and the GUIDE will disappear from screen

Device Buttons -

Press device buttons ONCE to

activate other entertainment devices such as a DVD

Player.

(You will need to use the remote control from

your external device thereafter if you don’t program

your device with the UE remote).

(HINT: pressing

LIST>PVR allows access to your DVR.

STEP 1 - Turn ON or OFF your TV

Press the TV button ONCE

(The TV button will

light up red

when pressed

and will go off when released)

Press the Power button ONCE

(The TV turns on. Pressing Power button

again turns TV off)

You don’t need to press TV button to change

channels or control the TV volume!

IMPORTANT - YOUR TV MUST BE SET TO CHANNEL __________

TO BE ABLE TO RECEIVE ENDEAVOR CHANNELS

> Select ON DEMAND>RENTALS to

select and purchase a VOD movie

STEP 2 - Turn ON Set Top Box (STB)

Press the STB button ONCE

(The STB button will

light up red

when pressed

and will go off when released)

Press the Power button ONCE

(The STB turns on. The BLUE POWER

LIGHT will be illuminated. If this light is

GRAY, repeat above step)

After pressing the STB button you can:

> Adjust the channels up or down

> Access the GUIDE, MENU and INFO

> Adjust the volume up or down

Quick Start Guide to Using Your

Remote Control

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione