Endress+Hauser Flexdip CYA112 Manuale utente

Products Solutions Services

BA00432C/07/EN/13.13

71207066

Operating Instructions

Flexdip CYA112

Wastewater assembly

Endress+Hauser

About this document

Safety messages

The structure, signal words and safety colors of the signs comply with the specifications of

ANSI Z535.6 ("Product safety information in product manuals, instructions and other

collateral materials").

Symbols

Safety message structure Meaning

DANGER

Cause (/consequences)

Consequences if safety

message is not heeded

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the situation will result in a fatal or serious

injury.

WARNING

Cause (/consequences)

Consequences if safety

message is not heeded

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid the situation can result in a fatal or serious

injury.

CAUTION

Cause (/consequences)

Consequences if safety

message is not heeded

‣Corrective action

This symbol alerts you to a dangerous situation.

Failure to avoid this situation can result in minor or

medium injury.

NOTICE

Cause/situation

Consequences if safety

message is not heeded

‣Action/note

This symbol alerts you to situations that can result in

damage to property and equipment.

Additional information, tips

Permitted or recommended

Forbidden or not recommended

Flexdip CYA112

Endress+Hauser 3

Table of contents

1 Basic safety instructions . . . . . . . . . . . . . 4

1.1 Requirements for the personnel . . . . . . . . . . . . . . . 4

1.2 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.3 Workplace safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.4 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.5 Product safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2 Incoming acceptance and product

identification . . . . . . . . . . . . . . . . . . . . . . 5

2.1 Incoming acceptance . . . . . . . . . . . . . . . . . . . . . . . . 5

2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.3 Product identification . . . . . . . . . . . . . . . . . . . . . . . . 5

2.4 Certificates and approvals . . . . . . . . . . . . . . . . . . . . 6

3 Installation . . . . . . . . . . . . . . . . . . . . . . . . 7

3.1 Installation conditions . . . . . . . . . . . . . . . . . . . . . . . 7

3.2 Installation instructions . . . . . . . . . . . . . . . . . . . . . . 8

3.3 Post-installation check . . . . . . . . . . . . . . . . . . . . . 15

4 Maintenance. . . . . . . . . . . . . . . . . . . . . . 16

4.1 Immersion pipe support . . . . . . . . . . . . . . . . . . . . 16

4.2 Maintaining the clamping systems and threads 16

4.3 Cleaning the quick fastener . . . . . . . . . . . . . . . . . 16

5 Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.1 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5.2 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

6 Accessories . . . . . . . . . . . . . . . . . . . . . . .18

7 Technical Data . . . . . . . . . . . . . . . . . . . .28

7.1 Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

7.2 Process conditions . . . . . . . . . . . . . . . . . . . . . . . . . 28

7.3 Mechanical construction . . . . . . . . . . . . . . . . . . . 28

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Basic safety instructions Flexdip CYA112

4Endress+Hauser

1 Basic safety instructions

1.1 Requirements for the personnel

‣Installation, commissioning, operation and maintenance of the measuring system must

only be carried out by trained technical personnel.

‣The technical personnel must be authorized by the plant operator to carry out the

specified activities.

‣The electrical connection may only be performed by an electrical technician.

‣The technical personnel must have read and understood these Operating Instructions

and must follow the instructions they contain.

‣Measuring point faults may only be rectified by authorized and specially trained

personnel.

Repairs not described in the enclosed Operating Instructions may only be carried out

directly at the manufacturer's or by the service organization.

1.2 Designated use

CYA112 is designed as a modular assembly system for sensors in open basins, channels and

tanks.

Any other use than the one described here compromises the safety of persons and the entire

measuring system and is not permitted.

The manufacturer is not liable for damage caused by improper or non-designated use.

1.3 Workplace safety

As the user, you are responsible for complying with the following safety conditions:

• Installation instructions

• Local prevailing standards and regulations.

1.4 Operational safety

‣Before commissioning the entire measuring point, make sure all the connections are

correct. Ensure that electrical cables and hose connections are not damaged.

‣Do not operate damaged products, and safeguard them to ensure that they are not

operated inadvertently. Mark the damaged product as defective.

‣If faults cannot be rectified, the products must be taken out of service and secured against

unintentional commissioning.

1.5 Product safety

The product is designed to meet state-of-the-art safety requirements, has been tested and

left the factory in a condition in which it is safe to operate. Relevant regulations and

European standards have been observed.

Flexdip CYA112 Incoming acceptance and product identification

Endress+Hauser 5

2 Incoming acceptance and product

identification

2.1 Incoming acceptance

‣Make sure the packaging is undamaged!

‣Inform the supplier about any damage to the packaging.

Keep the damaged packaging until the matter has been settled.

‣Make sure the contents are undamaged!

‣Inform the supplier about damage to the contents. Keep the damaged products until the

matter has been settled.

‣Check that the order is complete and agrees with your shipping documents.

‣The packaging material used to store or to transport the product must provide shock

protection and humidity protection. The original packaging offers the best protection.

Also, keep to the approved ambient conditions (see "Technical data").

‣If you have any questions, please contact your supplier or your local sales center.

2.2 Scope of delivery

The scope of delivery comprises:

• Ordered assembly version

• Operating Instructions, English.

If you have any questions, please contact your supplier or your local sales center.

2.3 Product identification

2.3.1 Nameplate

The nameplate contains the following information:

• Manufacturer data

•Ordercode

• Extended order code

• Serial number

• Operating conditions

•Safetyicons

Compare the order code on the nameplate with your order.

2.3.2 Identifying the product

The order code and serial number of your device can be found in the following locations:

•Onthenameplate

• In the delivery papers

To find out the version of your device, enter the order code indicated on the nameplate

in the search screen at the following address:

www.products.endress.com/order-ident

Incoming acceptance and product identification Flexdip CYA112

6Endress+Hauser

2.4 Certificates and approvals

Explosion protection

The stainless steel version of the CYA112 assembly (CYA112-*A21*2**) is suitable for use

in hazardous zones 1 and 2.

The ATEX directive 94/9/EC does not apply because the assembly has no potential ignition

source. Accordingly, it is not designated according to ATEX. Potential equalization must be

implemented as described in the chapter "Installation conditions".

If sensors have accessible metallic surfaces, these surfaces have to be connected to the

potential match according to the corresponding operating instructions.

Flexdip CYA112 Installation

Endress+Hauser 7

3Installation

3.1 Installation conditions

Install the assembly on a place with enough free space around it so the sensor cannot get

damaged.

When installing the assembly in a fixed position, make sure that it can be easily accessed and

maintained. The immersion pipe has to protrude the holding point by at least 100 mm

(3.94")

a0011037

Fig. 1: Holding point (illustration without splash protection cap)

The grounding has to be done on-site. All conductive parts have to be connected to each

other.

For use in hazardous areas:

• The immersion pipe side of the assembly has to be conductively connected to the

corresponding holder or fixing.

• When the assembly is fixed via chain or mounting bracket a separate conductor for

potential match is needed beside the measuring cable.

• If sensors have accessible metallic surfaces, these surfaces have to be connected to the

potential match according to the corresponding operating instructions.

min. 100

(3.94)

mm (inch)

Installation Flexdip CYA112

8Endress+Hauser

3.2 Installation instructions

3.2.1 Mounting the stainless steel parts

You have to screw the pipes together finger-tight (without any gaps). The threads are

lubricated and provided with an O-ring.

3.2.2 Gluing the PVC parts

PVC assemblies up to 1200 mm (47.2") in size are delivered as ready-to-install units

and do not have to be glued.

Where required, cleaning cloths and glues form part of the scope of supply.

Glue the PVC parts as follows:

1. Clean the surfaces to be glued (exterior pipe end, sleeve or internal angle piece) with the

cleaning cloth.

2. Allow the cleaned surfaces to dry for approx. 5 minutes.

3. Apply an even film of glue to the surfaces to be glued (sleeve first, then the pipe).

4. Join the parts within one minute (push together until the stop).

5. Remove the excess glue.

6. Allow the glued parts to harden for at least 5 minutes.

Flexdip CYA112 Installation

Endress+Hauser 9

3.2.3 Mounting the sensor

Preparatory steps:

1. Screw or glue the connecting bracket onto the immersion tube.

2. Where necessary, screw the sensor adapter onto the connection bracket.

Mount the sensor as follows:

1. Guide the sensor cable through the immersion tube.

2. Where necessary, connect the sensor cable to the sensor.

3. Screw the sensor into the adapter or into the connection bracket. To prevent the sensor

cable from twisting, rotate the assembly and not the sensor.

4. Shorten the tip of the rubber plug so that it suits the cable diameter.

5. Fit the rubber plug onto the sensor cable and press it onto the immersion tube.

6. Route the sensor cable downwards in a loop (do not bend) and fit on the splash

protection cap. The splash protection cap is fixed by the lip of the rubber plug.

a0011111

Fig. 2: Cable run

Splash protection cap

Sensor cable

Rubber plug

Immersion tube

Installation Flexdip CYA112

10 Endress+Hauser

3.2.4 Fixed installation of the assembly on a transverse pipe

Prerequisite: The sensor is already mounted.

The cross clamp is mounted in such a way that one closed side points to the center of

the basin while the other closed side points upwards.

Mount the immersion tube as follows:

1. Adjust the clamps on the cross clamp (å4).

2. Slide the cross clamp over the immersion tube. Make sure that the closed side of the

cross clamp is at the top (å3).

3. Mount the multifunctional clamp ring (funnel-shaped side facing upwards) on the

immersion tube above the cross clamp. The multifunctional clamp ring acts as an anti-

slip lock.

4. Attach the cross clamp, along with the immersion tube, to the transverse pipe. Make

sure that the closed side of the cross clamp faces the basin (å3).

5. Align the assembly and the holder.

6. Tighten the clamp screws finger-tight (finger-tight corresponds to 13 Nm (9.6 lbf ft)).

a0011292

Fig. 3: Mounting the cross clamp

Immersion tube

Cross clamp, closed side to basin center

Cross clamp, closed side at top

Transverse pipe

a0014991

Fig. 4: Adjustment of the clamps

Altri manuali per Flexdip CYA112

Indice

Altri manuali Endress+Hauser Strumento di misura

Endress+Hauser

Endress+Hauser Cerabar S PMP71 with MID Part Certificate Manuale utente

Endress+Hauser

Endress+Hauser RIA452 Manuale utente

Endress+Hauser

Endress+Hauser Deltapilot S FMB70 Specifiche tecniche

Endress+Hauser

Endress+Hauser Cerabar PMC71B Specifiche tecniche

Endress+Hauser

Endress+Hauser Levelflex M FMP45 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promass O 300 Manuale

Endress+Hauser

Endress+Hauser ria45 Specifiche tecniche

Endress+Hauser

Endress+Hauser Liquiphant M with FEL56 Istruzioni per l’uso

Endress+Hauser

Endress+Hauser Minicap FTC260 Manuale utente

Endress+Hauser

Endress+Hauser Proline Cubemass 500 Istruzioni per l’uso

Endress+Hauser

Endress+Hauser Gammapilot M FMG60 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag H 500 Manuale utente

Endress+Hauser

Endress+Hauser Proline Prosonic Flow 91 Manuale utente

Endress+Hauser

Endress+Hauser Gammapilot M FMG60 Manuale utente

Endress+Hauser

Endress+Hauser Levelflex FMP55 Specifiche tecniche

Endress+Hauser

Endress+Hauser Deltabar FMD72 Manuale

Endress+Hauser

Endress+Hauser analytikjena Biometra TOne Manuale utente

Endress+Hauser

Endress+Hauser FMU 40 Manuale elenco delle parti

Endress+Hauser

Endress+Hauser Conducal CLY421 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar S Specifiche tecniche

Endress+Hauser

Endress+Hauser Micropilot II Manuale utente

Endress+Hauser

Endress+Hauser Proline Cubemass C 500 Manuale

Endress+Hauser

Endress+Hauser Micropilot M FMR250 Manuale

Endress+Hauser

Endress+Hauser HART Proline t-mass I 300 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente

Acterna

Acterna MS1400 Manuale utente

R&S

R&S ZPH Manuale utente