Endress+Hauser Proservo NMS83 Specifiche tecniche
Products Solutions Services
Brief Operating Instructions
Proservo NMS83
Tank Gauging
These Instructions are Brief Operating Instructions; they are
not a substitute for the Operating Instructions pertaining to
the device.
Detailed information about the device can be found in the
Operating Instructions and the other documentation:
Available for all device versions via:
– Internet: www.endress.com/deviceviewer
– Smart phone/tablet: Endress+Hauser Operations App
KA01206G/00/EN/02.17
71364766
Proservo NMS83
2 Endress+Hauser
Order code:
Ext. ord. cd.:
Ser. no.:
www.endress.com/deviceviewer Endress+Hauser
Operations App
XXXXXXXXXXXX
XXXXX-XXXXXX
XXX.XXXX.XX
Serial number
1.
3.
2.
A0023555
Proservo NMS83 Table of contents
Endress+Hauser 3
Table of contents
1 About this document .............................................................. 4
1.1 Symbols ............................................................................. 4
2 Basic safety instructions .......................................................... 6
2.1 Requirements for the personnel ............................................................ 6
2.2 Designated use ........................................................................ 6
2.3 Workplace safety ...................................................................... 6
2.4 Operational safety ......................................................................7
2.5 Product safety ......................................................................... 7
3 Product description ............................................................... 8
3.1 Product design ........................................................................ 8
4 Incoming acceptance and product identification ................................... 9
4.1 Incoming acceptance ................................................................... 9
4.2 Product identification ................................................................... 9
4.3 Storage and transport ................................................................... 9
5 Installation ...................................................................... 11
5.1 Requirements ........................................................................ 11
5.2 Mounting of the device ................................................................. 13
6 Electrical connection ............................................................ 20
6.1 Terminal assignment .................................................................. 20
6.2 Connecting requirements ............................................................... 33
6.3 Ensuring the degree of protection ......................................................... 34
7 Commissioning .................................................................. 35
7.1 Operating methods .................................................................... 35
7.2 Terms related to tank measurement ....................................................... 38
7.3 Setting the display language ............................................................. 39
7.4 Calibration .......................................................................... 40
7.5 Configuration of the inputs .............................................................. 48
7.6 Linking measured values to tank variables ................................................... 56
7.7 Configuration of the limit evaluation ....................................................... 57
7.8 Configuration of the signal output ......................................................... 59
About this document Proservo NMS83
4 Endress+Hauser
1 About this document
1.1 Symbols
1.1.1 Safety symbols
Symbol Meaning
DANGER
DANGER!
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
CAUTION!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
NOTE!
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.1.2 Electrical symbols
Symbol Meaning Symbol Meaning
Direct current Alternating current
Direct current and alternating current Ground connection
A grounded terminal which, as far as
the operator is concerned, is grounded
via a grounding system.
Symbol Meaning
Protective ground connection
A terminal which must be connected to ground prior to establishing any other connections.
Equipotential connection
A connection that has to be connected to the plant grounding system: This may be a potential
equalization line or a star grounding system depending on national or company codes of practice.
1.1.3 Tool symbols
A0011219 A0011220 A0013442 A0011221 A0011222
Cross-head
screwdriver
Flat blade
screwdriver Torx screwdriver Allen key Hexagon wrench
Proservo NMS83 About this document
Endress+Hauser 5
1.1.4 Symbols for certain types of information
Symbol Meaning Symbol Meaning
Permitted
Procedures, processes or actions that
are permitted.
Preferred
Procedures, processes or actions that
are preferred.
Forbidden
Procedures, processes or actions that
are forbidden.
Tip
Indicates additional information.
Reference to documentation
A
Reference to page
Reference to graphic
1.
,
2.
,
3.
… Series of steps
Result of a step Visual inspection
1.1.5 Symbols in graphics
Symbol Meaning
1, 2, 3 ... Item numbers
1.
,
2.
,
3.
… Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections
-
Hazardous area
Indicates a hazardous area.
.
Safe area (non-hazardous area)
Indicates the non-hazardous area.
1.1.6 Symbols at the device
Symbol Meaning
Safety instructions
Observe the safety instructions contained in the associated Operating Instructions.
Temperature resistance of the connection cables
Specifies the minimum value of the temperature resistance of the connection cables.
Basic safety instructions Proservo NMS83
6 Endress+Hauser
2 Basic safety instructions
2.1 Requirements for the personnel
The personnel must fulfill the following requirements for its tasks:
‣Trained, qualified specialists must have a relevant qualification for this specific function
and task.
‣Are authorized by the plant owner/operator.
‣Are familiar with federal/national regulations.
‣Before starting work, read and understand the instructions in the manual and
supplementary documentation as well as the certificates (depending on the application).
‣Follow instructions and comply with basic conditions.
2.2 Designated use
Application and measured materials
Depending on the version ordered, the measuring device can also measure potentially
explosive, flammable, poisonous and oxidizing media.
Measuring devices for use in hazardous areas, in hygienic applications or in applications
where there is an increased risk due to process pressure, are labeled accordingly on the
nameplate.
To ensure that the measuring device remains in proper condition for the operation time:
‣Only use the measuring device in full compliance with the data on the nameplate and the
general conditions listed in the Operating Instructions and supplementary documentation.
‣Check the nameplate to verify if the device ordered can be put to its intended use in the
approval-related area (e.g. explosion protection, pressure vessel safety).
‣Use the measuring device only for media against which the process-wetted materials are
adequately resistant.
‣If the measuring device is not operated at atmospheric temperature, compliance with the
relevant basic conditions specified in the associated device documentation is absolutely
essential.
‣Protect the measuring device permanently against corrosion from environmental
influences.
‣Observe the limit values in the "Technical Information".
The manufacturer is not liable for damage caused by improper or non-designated use.
Residual risk
During operation the sensor may assume a temperature near the temperature of the
measured material.
Danger of burns due to heated surfaces!
‣For high process temperatures: Install protection against contact in order to prevent burns.
2.3 Workplace safety
For work on and with the device:
‣Wear the required personal protective equipment according to federal/national
regulations.
Proservo NMS83 Basic safety instructions
Endress+Hauser 7
2.4 Operational safety
Risk of injury.
‣Operate the device in proper technical condition and fail-safe condition only.
‣The operator is responsible for interference-free operation of the device.
Conversions to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable
dangers.
‣If, despite this, modifications are required, consult with the manufacturer.
Repair
To ensure continued operational safety and reliability,
‣Carry out repairs on the device only if they are expressly permitted.
‣Observe federal/national regulations pertaining to repair of an electrical device.
‣Use original spare parts and accessories from the manufacturer only.
Hazardous area
To eliminate a danger for persons or for the facility when the device is used in the hazardous
area (e.g. explosion protection, pressure vessel safety):
‣Based on the nameplate, check whether the ordered device is permitted for the intended
use in the hazardous area.
‣Observe the specifications in the separate supplementary documentation that is an integral
part of these Instructions.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet state-
of-the-art safety requirements, has been tested, and left the factory in a condition in which it
is safe to operate. It meets general safety standards and legal requirements.
2.5.1 CE mark
The measuring system meets the legal requirements of the applicable EC guidelines. These are
listed in the corresponding EC Declaration of Conformity together with the standards applied.
Endress+Hauser confirms successful testing of the device by affixing to it the CE mark.
Product description Proservo NMS83
8 Endress+Hauser
3 Product description
3.1 Product design
5
6
7
8
1
2
3
49
A0028873
1 Configuration of NMS83
1 Front cover
2 Display
3 Modules
4 Sensor unit
5 Housing
6 Wire drum
7 Bracket
8 Housing cover
9 Displacer
Proservo NMS83 Incoming acceptance and product identification
Endress+Hauser 9
4 Incoming acceptance and product identification
4.1 Incoming acceptance
Upon receipt of the goods check the following:
• Are the order codes on the delivery note and the product sticker identical?
• Are the goods undamaged?
• Do the nameplate data match the ordering information on the delivery note?
• If required (see nameplate): Are the Safety Instructions (XA) enclosed?
If one of these conditions is not satisfied, contact your Endress+Hauser Sales Center.
4.2 Product identification
The following options are available for identification of the measuring device:
• Nameplate specifications
• Extended order code with breakdown of the device features on the delivery note
• Enter serial numbers from nameplates in W@M Device Viewer
( www.endress.com/deviceviewer ): All information about the measuring device is
displayed.
• Enter the serial number from the nameplates into the Endress+Hauser Operations App or
scan the 2-D matrix code (QR code) on the nameplate with the Endress+Hauser Operations
App: all the information for the measuring device is displayed.
For an overview of the scope of the associated Technical Documentation, refer to the
following:
• The W@M Device Viewer: Enter the serial number from the nameplate
(www.endress.com/deviceviewer)
• The Endress+Hauser Operations App: Enter the serial number from the nameplate or scan
the 2-D matrix code (QR code) on the nameplate.
4.2.1 Manufacturer address
Endress+Hauser GmbH+Co. KG
Hauptstraße 1
79689 Maulburg, Germany
Address of the manufacturing plant: See nameplate.
4.3 Storage and transport
4.3.1 Storage conditions
• Storage temperature: –50 to +80 °C (–58 to +176 °F)
• Store the device in its original packaging.
Incoming acceptance and product identification Proservo NMS83
10 Endress+Hauser
4.3.2 Transport
NOTICE
Risk of injury
‣Transport the measuring device to the measuring point in its original packaging.
‣Take into account the mass center of the device in order to avoid unintended tilting.
‣Comply with the safety instructions, transport conditions for devices over 18kg (39.6lbs)
(IEC61010).
Altri manuali per Proservo NMS83
1
Indice
Altri manuali Endress+Hauser Strumento di misura
Endress+Hauser
Endress+Hauser Deltabar PMD55B Manuale utente
Endress+Hauser
Endress+Hauser Stamolys CA71NO Manuale utente
Endress+Hauser
Endress+Hauser Prosonic S FMU90 Manuale utente
Endress+Hauser
Endress+Hauser Micropilot FMR54 Istruzioni per l'installazione
Endress+Hauser
Endress+Hauser UniFit CPA 441 Manuale utente
Endress+Hauser
Endress+Hauser Micropilot FMR51 Specifiche tecniche
Endress+Hauser
Endress+Hauser Proline 500 Specifiche tecniche
Endress+Hauser
Endress+Hauser PROline promag 53 Manuale utente
Endress+Hauser
Endress+Hauser Proline Promag 10D Manuale
Endress+Hauser
Endress+Hauser Levelflex M FMP40 Manuale utente
Endress+Hauser
Endress+Hauser Proline Prowirl F 200 Manuale utente
Endress+Hauser
Endress+Hauser Gammapilot FMG50 Manuale
Endress+Hauser
Endress+Hauser Deltapilot S FMB70 Istruzioni per l’uso
Endress+Hauser
Endress+Hauser Omnigrad M TR44 Manuale
Endress+Hauser
Endress+Hauser Proline t-mass I 500 Manuale
Endress+Hauser
Endress+Hauser Smartec S CLD134 Manuale utente
Endress+Hauser
Endress+Hauser Micropilot FMR62 Manuale
Endress+Hauser
Endress+Hauser Proline Prosonic Flow 93T Portable Manuale utente
Endress+Hauser
Endress+Hauser Proline Promass 83 Manuale utente
Endress+Hauser
Endress+Hauser 11362Z Istruzioni per l'installazione
