Eneo VM-FHD22PP Manuale utente
EN
Installation Manual
22” (56cm) LCD Monitor,
1920x1080, LED, HDMI, VGA,
RJ45, PoE Port
VM-FHD22PP
DE
2
Table of contents
Components...................................................................................................................5
Introduction...................................................................................................................6
Connectors ..........................................................................................................................................................................6
Control buttons on the remote control ....................................................................................................................7
Inserting the batteries.....................................................................................................................................................7
Startup ...........................................................................................................................8
Switch the monitor ON and OFF..................................................................................................................................8
PC Connection ...................................................................................................................................................................8
Basic OSD setup.................................................................................................................................................................8
Turning on and o the CCTV monitor ..................................................................................................................8
Selecting screen language .......................................................................................................................................9
No signal .........................................................................................................................................................................9
Select input signal .................................................................................................................................................... 10
OSD Menu......................................................................................................................................................................... 10
Picture Menu .............................................................................................................................................................. 10
Color Mode Medium (From Picture Submenu )..............................................................................................11
Aspect Ratio (From Picture Submenu ) ..............................................................................................................11
Noise Reduction (From Picture Submenu )..................................................................................................... 12
User Reset Options................................................................................................................................................... 12
Troubleshooting ......................................................................................................... 13
General Section............................................................................................................................................................... 13
Problems with VGA connection................................................................................................................................ 13
Further information .................................................................................................. 14
3
EN
Safety instructions
General safety instructions
• Before switching on and operating the system, rst read this safety advice and the operating instructions.
• Keep the operating instructions in a safe place for later use.
• Installation, commissioning and maintenance of the system may only be carried out by authorised indi-
viduals and in accordance with the installation instructions - ensuring that all applicable standards and
guidelines are followed.
• Protect the devices from water penetration and humidity, since these can cause lasting damage.
• Should moisture nevertheless enter the system, under no circumstance switch on the devices under these
conditions, instead send them for examination to an authorised specialist workshop.
• The system must never be used outside of the technical specications, since this can destroy it.
• The device must be protected from excesses of heat, dust, humidity and vibration.
• When separating the system from the voltage supply, only ever use the plug to pull out the cable. Never
pull directly on the cable itself.
• Lay the connecting cables carefully and check that they are not mechanically stressed, kinked or damaged
and that no humidity can penetrate into them.
• In the event of a malfunction, please inform your supplier.
• Maintenance and repairs may only be carried out by authorised specialist personnel.
• The system must be isolated from the power supply before opening the housing.
• The device may only be opened by qualied service personnel. Unauthorised access invalidates any
warranty claim.
• Connection cables should always be exchanged through VIDEOR E. Hartig GmbH.
• Use only original spare parts and accessories from VIDEOR E. Hartig GmbH.
• The housing should only be cleaned using a mild domestic cleaning agent. Never use solvents or petrol as
these can permanently damage the surface.
• During installation, it is essential to ensure that the seals provided are correctly installed and that they are
not displaced during installation. Damaged seals must not be installed and will invalidate any warranty.
• The installer is responsible for the maintenance of the enclosure as per the technical data, e.g. by sealing
the cable outlets with silicone.
• Wire end ferrules should be used when shortening the exible connection cables.
• The devices may only be operated in the temperature range indicated in the data sheet and within the
dened air humidity range.
4
WEEE (Waste Electrical & Electronic Equipment)
Correct Disposal of This Product (Applicable in the European Union and other European countries with separate
collection systems).
This marking shown on the product or its literature, indicates that it should not be disposed with
other household wastes at the end of its working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate this from other types of wastes
and recycle it responsibly to promote the sustainable reuse of material resources. Household users
should contact either the retailer where they purchased this product, or their local government
oce, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product should not be mixed with other commercial wastes for disposal.
Graphical symbols
Please pay attention to the safety instructions, and carefully read through this instruction guide before initial
operation.
Important points of warning are marked with a caution symbol.
iImportant points of advice are marked with a notice symbol.
5
EN
Components
This system comes with the following components:
• Monitor
• Installation Guide
• Remote Control
• Power Cord
• Power Cable
6
Introduction
Connectors
No. Label Description of the function
1 POWER 12V input
2 HDMI HDMI input
3VGA VGA input
4 USB USB Port
5 AUDIO Audio IN
6 AUDIO Audio OUT
7 RJ45 PoE Input
8 RJ45 LAN Output
7
EN
Control buttons on the remote control
Switch on monitor when at standby mode
or vice versa.
Press to mute the sound. Press again or press
VOL+ to unmute.
Menu selection
Press to increase / decrease
Press to bring up the main menu to the screen
and exit the current menu.
Press to cycle through the input source
Press repeatedly to cycle through the available
video picture.
Inserting the batteries
Open the battery compartment cover on the back of the remote
control.
Insert one CR2032 3V battery with the correct polarity into the com-
partment. Please use only new batteries.
Close the compartment cover again.
Hold the remote control in the direction of the infrared sensor. The
distance to the monitor must not exceed 7 meters.
iNote: Please do not throw the used batteries into the household waste, but dispose of
them in an environmentally friendly manner at the appropriate collection points.
8
Startup
Switch the monitor ON and OFF
Connect the power cord to the monitor and the power source. Turn on the monitor using
the power button on the monitor or remote control. The power indication on the front
panel lights green. Press the power button again to turn o the monitor.
PC Connection
This CCTV monitor provides plug and play capability, meaning that the PC adjusts
automatically to the monitor’s setting. The CCTV monitor sends conguration informa-
tion (EDID) to the PC using the Video Electronics Standard Association (VESA) Display
Data Channel (DDC) protocol.
1. Connect the RGB Output of the PC to the VGA in jack on the set.
2. Turn on the PC and set.
3. Select the VGA input source with using INPUT button on the remote control.
Basic OSD setup
Turning on and o the CCTV monitor
1. Turn on monitor
Monitor Back
PC Back
PC Audio Cable
VGA Cable
9
EN
• Connect the AC input cable to monitor, then press the main power switch on mon-
itor. At this time the monitor will enter into standby mode and the indicator light
turn red.
• Using buttons can turn on monitor from standby mode as follows: Press POWER
keyon front panel or on the remote control.
2. Turn o monitor
• Press POWER button on front panel the or on the remote control to enter standby
mode. The indicator light is red.
• Using main power switch turns o monitor completely.
Selecting screen language
Note: lf you use your monitor for the rst time.you should select the language which
will be used for displaying menus and indications.
• Press the“MENU” button into main menu.
• Press the button toselect OSD menu.
• Press the button to select OSD LANGUAGE.
• Press the button toselect your language.
• When you are satised with your choice, press MENU to exit.
No signal
If the monitor does not receive an input signal, this character is displayed:
i
10
Select input signal
Press the INPUT button on the remote control or on the monitor to select the input signal.
• Press ▼ ▲to select the correct input signal
• Conrm the selection with the INPUT button on the remote control
OSD Menu
• Press the MENU button to access Main Menu setting interface
• Press the ◄► to select the desired submenu
• Press the ▼▲ again to enter the submenu
Picture Menu
• Press ◄► button to select PC menu
• Use ▼▲ to select what you want to adjust in the VGA/HDMI mode
• Press ◄► button to adjust
• When you are satised with your adjustment, press MENU to exit the main menu
Indice
Lingue:
Altri manuali Eneo Monitor
Eneo
Eneo VM-FHD10M Manuale utente
Eneo
Eneo VMC-8LCD-CM01B Manuale utente
Eneo
Eneo VMC-19LEDM Manuale utente
Eneo
Eneo PCS-19/DVR-08 Manuale utente
Eneo
Eneo VMC-6.4LCD-P1 Manuale utente
Eneo
Eneo VMC-8.4LCD-CM Manuale utente
Eneo
Eneo VMC-5.6/1-LCD Manuale utente
Eneo
Eneo VM-FHD10M Manuale utente
Eneo
Eneo VMC-22LED Manuale utente
Eneo
Eneo VM-FHD24PF Manuale utente
Eneo
Eneo VMC-27LEDM Guida utente
Eneo
Eneo VM-FHD12M Manuale utente
Eneo
Eneo VMC-26LCD-PW1 Manuale utente
Eneo
Eneo VMC-19LEDMD Manuale utente
Eneo
Eneo VMC-8LCD-CP01B Manuale utente
Eneo
Eneo VMC-17LCD-HPC1 Manuale utente
Eneo
Eneo VM-UHD32M Manuale utente
Eneo
Eneo VM-FHD27MP Manuale utente
Eneo
Eneo VMC-10/2 Manuale utente
Eneo
Eneo VMC-27LEDM Manuale utente
