Enertronica Santerno SOLARDRIVE PLUS Istruzioni operative

•15R00SDB100 •

SOLARDRIVE

PLUS

AC DRIVE FOR SOLAR PUMPING APPLICATIONS

PROGRAMMING GUIDE

Agg. 14/05/2020

R. 00

SW Ver. 4.10x

•This manual is integrant and essential to the product. Carefully read the instructions contained herein

as they provide important hints for use and maintenance safety.

•This product is to be used only for the purposes it has been designed to. Other uses should be

considered improper and dangerous. The manufacturer is not responsible for possible damages

caused by improper, erroneous and irrational uses.

•Enertronica Santerno is responsible for the product in its original setting.

•Any changes to the structure or operating cycle of the product must be performed or authorized by

Enertronica Santerno.

•Enertronica Santerno assumes no responsibility for the consequences resulting by the use of non-

original spare-parts.

•Enertronica Santerno reserves the right to make any technical changes to this manual and to the

product without prior notice. If printing errors or similar are detected, the corrections will be included in

the new releases of the manual.

•The information contained herein is the property of Enertronica Santerno and cannot be reproduced.

Enertronica Santerno enforces its rights on the drawings and catalogues according to the law.

Enertronica Santerno S.p.A.

Via della Concia, 7 - 40023 Castel Guelfo (BO) Italy

Tel. +39 0542 489711 - Fax +39 0542 489722

santerno.com [email protected]

English

SOLARDRIVE

PLUS

PROGRAMMING

GUIDE

2/107

USER MANUALS MENTIONED IN THIS PROGRAMMING GUIDE

The following User Manuals from Enertronica Santerno are mentioned throughout this Programming Guide:

-15P00SDB100 Solardrive Plus –Installation Manual

-15W0102B300 Safe Torque Off Function –Application Manual

-15W0102B500 Motor Drives Accessories - User Manual

-15G0851B100 DATA LOGGER ES851 - Programming Guide

-15P4600B100 BRIDGE MINI - User manual

-15J0901B100 RemoteDrive DRIVE REMOTE CONTROL - User Manual

PROGRAMMING 
GUIDE 
 
SOLARDRIVE 
PLUS
 
3/107 
 
TABLE OF CONTENTS 
1. CHAPTERS 
 
TABLE OF CONTENTS ............................................................................................3 
1. CHAPTERS ....................................................................................................3 
2. FIGURES........................................................................................................5 
3. TABLES..........................................................................................................5 
GENERAL INFORMATION.......................................................................................6 
1. GENERAL INFORMATION ON THE PRODUCT............................................6 
1.1. SOLARDRIVE PLUS.......................................................................................................6
1.2. SOLARDRIVE PLUS BOX..............................................................................................7
1.3. SOLARDRIVE PLUS CABINET......................................................................................8
2. SCOPE OF THIS MANUAL.............................................................................8 
3. FOR WHOM THIS MANUAL IS INTENDED...................................................8 
PROGRAMMING.......................................................................................................9 
1. GENERAL SPECIFICATIONS........................................................................9 
1.1. OVERVIEW.....................................................................................................................9
1.2. MENUS AND SUBMENUS...........................................................................................10 
1.3. ALARMS AND WARNINGS..........................................................................................12 
2. USING THE DISPLAY/KEYPAD UNIT.......................................................... 13 
2.1. OVERVIEW...................................................................................................................13 
2.2. MENU TREE.................................................................................................................14 
2.3. NAVIGATION................................................................................................................16 
2.4. PARAMETER MODIFICATION ....................................................................................17 
2.5. PROGRAMMING THE ROOT PAGE ...........................................................................17 
2.6. USING THE MENU KEY...............................................................................................18 
2.7. ESC KEY.......................................................................................................................19 
2.8. RESET KEY (ALARM AND CONTROL BOARD RESET)............................................20 
2.9. TX/RX KEY (DOWNLOAD/UPLOAD FROM/TO THE KEYPAD).................................21 
2.10. LOC/REM KEY..............................................................................................................22 
2.11. SAVE/ENTER KEY.......................................................................................................23 
2.12. START-UP KEY............................................................................................................23 
2.13. INDICATOR LEDS ON THE DISPLAY/KEYPAD..........................................................24 
2.14. ROOT PAGE.................................................................................................................25 
2.15. KEYPAD PAGE AND LOCAL MODE ...........................................................................26 
3. MANUAL MODE (LOCAL MODE)................................................................. 27 
4. START UP MENU......................................................................................... 28 
4.1. OVERVIEW...................................................................................................................28 

SOLARDRIVE 
PLUS 
 
PROGRAMMING 
GUIDE 
 
4/107 
4.2. FIRST START UP.........................................................................................................30 
5. MEASURES MENU....................................................................................... 34 
5.1. OVERVIEW...................................................................................................................34 
5.2. MOTOR MEASURES MENU........................................................................................35 
5.3. DIGITAL INPUTS MENU..............................................................................................37 
5.4. OUTPUTS MENU.........................................................................................................39 
5.5. AUTODIAGNOSTICS MENU........................................................................................40 
5.6. FAULT LIST MENU ......................................................................................................42 
5.7. POWER OFF LIST MENU............................................................................................44 
6. PARAMETERS MENU..................................................................................46 
6.1. RAMPS MENU..............................................................................................................46 
6.2. DRY-RUN CONTROL MENU.......................................................................................51 
6.3. PIPE FILL CONTROL MENU .......................................................................................55 
6.4. MOTOR CONFIGURATION MENU..............................................................................57 
6.5. LIMITS MENU...............................................................................................................68 
6.6. CONTROL METHOD MENU........................................................................................70 
6.7. AUTORESET MENU ....................................................................................................72 
6.8. MOTOR THERMAL PROTECTION MENU..................................................................74 
6.9. SOLARDRIVE –CONFIGURATION PARAMETERS MENU.......................................77 
6.10. SOLARDRIVE –GENERAL PARAMETERS MENU ....................................................82 
6.11. SOLARDRIVE –MPPT PARAMETERS MENU ...........................................................84 
7. ALARMS AND WARNINGS.......................................................................... 89 
7.1. WHAT HAPPENS WHEN A PROTECTION TRIPS.....................................................89 
7.2. WHAT TO DO WHEN AN ALARM TRIPS....................................................................90 
7.3. ALARM LIST.................................................................................................................91 
7.4. WARNINGS................................................................................................................103 
7.5. WARNING LIST..........................................................................................................104 
7.6. STATE LIST................................................................................................................106 
 

PROGRAMMING 
GUIDE 
 
SOLARDRIVE 
PLUS
 
5/107 
 
0.2. Figures 
 
Figure 1: Solardrive Plus application ..................................................................................................................................6 
Figure 2: Solardrive Plus Box .............................................................................................................................................7 
Figure 3: Navigation example ...........................................................................................................................................16 
Figure 4: Display/Keypad of the Solardrive Plus...............................................................................................................24 
Figure 5: The ENABLE Function.......................................................................................................................................38 
Figure 6: Dry-run zone......................................................................................................................................................51 
Figure 7: Pipe Fill function ................................................................................................................................................55 
Figure 8: Types of programmable V/f curves....................................................................................................................58 
Figure 9: Trip current drop depending on speed values ...................................................................................................74 
Figure 10: Current reduction based on heatsink temperature ..........................................................................................78 
Figure 11: Voltage control algorithm.................................................................................................................................84 
Figure 12: Working point based on DC power..................................................................................................................85 
 
 
0.3. Tables 
 
Table 1: Coding of Measures M031, M032.......................................................................................................................39 
Table 2: Coding of Measures M033..................................................................................................................................39 
Table 3: Coding of Measure M056....................................................................................................................................39 
Table 4: Modbus base addresses in the Fault Lists..........................................................................................................43 
Table 5: List of the measures in the Fault Lists ................................................................................................................43 
Table 6: List of the measures in the Power Off List ..........................................................................................................45 
Table 7: Example of a Speed Ramp.................................................................................................................................46 
Table 8: Motor Ratings......................................................................................................................................................57 
Table 9: IFD control parameters for the connected motors ..............................................................................................59 
Table 10: Equivalence between AC mains range and DC range......................................................................................61 
Table 11: Maximum value of the output frequency depending on the drive size ..............................................................62 
Table 12: Digital inputs .....................................................................................................................................................77 
Table 13: List of the possible alarms ................................................................................................................................91 
Table 14: Warning list.....................................................................................................................................................104 
Table 15: State list..........................................................................................................................................................106 

SOLARDRIVE

PLUS

PROGRAMMING

GUIDE

6/107

1. GENERAL INFORMATION

1.1. General Information on the Product

The Solardrive Plus drives are designed to be utilized in pumping applications exploiting the energy

produced by a PV field.

They may be powered directly from a DC current PV field or the three-phase grid, or from an AC genset.

They control an electric submersible pump (ESP).

Figure 1: Solardrive Plus application

The Solardrive Plus line includes the following products:

1.1.1. Solardrive Plus

They are stand-alone inverters, which must be mounted inside a box or cabinet by the customer together with

•all the safety devices,

•the components required for the connection to the PV field and

•the components required for the connection to the pump.

PROGRAMMING

GUIDE

SOLARDRIVE

PLUS

7/107

1.1.2. Solardrive Plus Box

The Solardrive Plus Box models consist of a Solardrive Plus housed in a box.

This is a complete solution for medium-low power ranges, comprising the drive and all the safety devices, the

components required for the connection to the PV field and the components required for the connection to

the pump.

Figure 2: Solardrive Plus Box

The Solardrive Plus Box product line is suitable for motor mechanical power ratings ranging from 3 to

22 kW, with nominal currents up to 52 A, and output voltages up to 415 Vac 60 Hz.

Size

Nominal current

Applicable motor power

at 40°C

at 50°C

at 40°C

at 50°C

0018

13.6

5.5

7.5

5.5

0021

0024

0032

41.6

18.5

SOLARDRIVE

PLUS

PROGRAMMING

GUIDE

8/107

1.1.3. Solardrive Plus Cabinet

The Solardrive Plus Cabinet models consist of a Solardrive Plus housed in a cabinet.

This is a complete solution for large power ranges, comprising the drive and all the safety devices, the

components required for the connection to the PV field and the components required for the connection to

the pump.

The Solardrive Plus Cabinet line is suitable for motor mechanical power ratings ranging from 26 to 315 kW,

with nominal currents up to 640 A, and output voltages up to 415 Vac 60 Hz.

Taglia

Nominal current

Applicable motor power

at 40°C

at 50°C

at 40°C

at 50°C

0051

80.0

72.0

0069

105.0

84.0

0088

150.0

100

0164

230.0

184.0

110

150

125

0201

330.0

264.0

170

230

132

180

0259

400.0

320.0

190

260

170

230

0401

640.0

512.0

315

430

240

330

The Solardrive Plus and systems are designed and manufactured in Italy by Enertronica Santerno S.p.A.

1.2. Scope of this Manual

This manual covers:

•All products of the Solardrive Plus line.

1.3. For Whom this Manual is Intended

This manual must be read by:

•Installers

•Operators

•Plant manager

PROGRAMMING

GUIDE

SOLARDRIVE

PLUS

9/107

2. PROGRAMMING

2.1. General specifications

2.1.1. Overview

This section provides any information required to setup and monitor the drives of the Solardrive Plus series

manufactured by Enertronica Santerno SpA.

Setup/monitoring may be obtained using one of the following options:

•Display/keypad unit;

•Serial link through RS485 standard port.

Any information sent to/from the drive via the display/keypad unit may be obtained

also via serial link using the RemoteDrive software application offered by

Enertronica Santerno

RemoteDrive allows the following functions: image acquisition, keypad simulation,

oscilloscope functions and multifunction tester, data logger, table compiler

including history data, parameter setup and data reception-transmission-storage

from and to a calculator, scan function for the automatic detection of the

connected drives (up to 247 drives may be connected).

You can also create your own dedicated software via serial communication link. This manual provides any

information concerning addressing (Address field) and scaling (Range field) for the drive interfacing.

SOLARDRIVE

PLUS

PROGRAMMING

GUIDE

10/107

2.1.2. Menus and Submenus

This User Manual (Programming Guide) is divided into different Menus. Their sequence is the same as their

display sequence in the display/keypad and the RemoteDrive software

Programming parameters and Measure parameters are divided into:

Mxxx Measures (always Read Only):

Mxxx

Description

Range

Drive representation

(integer)

Display on the display/keypad and the RemoteDrive

(may be a decimal figure)

plus unit of measure

Active

Type of control the measure is related to

Address

Modbus address which the measure can be read from

(integer)

Function

Measure description

Pxxx Parameters (always R/W):

Pxxx

Description

Range

Drive representation

(integer)

Display on the display/keypad and the RemoteDrive

(may be a decimal figure)

plus unit of measure

Default

Factory-setting of the parameter

(as represented for the drive)

Factory-setting of the parameter

(as displayed)

plus unit of measure

Level

User level (BASIC / ADVANCED / ENGINEERING)

Address

Modbus address which the parameter can be read from

(integer)

Control

This optional field is displayed when a parameter is not active for all types of motor controls (IFD /

VTC / FOC)

Function

Parameter description

Indice

Manuali Azionamento CC popolari di altre marche

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuale utente

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuale elenco delle parti

Chamberlain Garog

Chamberlain Garog D Series Manuale utente

Parker

Parker PDS Series Manuale utente

Festo

Festo DGC G Series Guida all'installazione

Binks

Binks QS-5012-1-CE Manuale utente

Danfoss

Danfoss VLT 2800 Series Scheda tecnica

ABB

ABB ACQ580-01 Series Manuale di installazione

YASKAWA

YASKAWA CANopen SI-S3 Manuale utente

GE D20A6 Manuale utente

Unex

Unex MC-D-250-1000-050W-TW Manuale utente

Geckodrive

Geckodrive G213V Manuale utente

ABB

ABB RSYC-01 Manuale utente

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuale del proprietario

WEG

WEG DeviceNet CFW500 Manuale utente

Siemens

Siemens SINAMICS G Scheda tecnica

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Istruzioni operative

SOMFY

SOMFY JR RU 30 Manuale utente