Enerwave ZWN-RSM2-PLUS Manuale utente

INSTALLATION NSTRUCTIONS

WARRANTY INFORMATION

This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase. Original receipt

or proof of purchase from an authorized retailer must be presented upon warranty claim. ALL claims must be verified and

approved by Enerwave, Inc. Warranties from other Enerwave products may vary. This warranty is nontransferable and does

not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration,

modification, or improper installation. To the fullest extent permitted by the applicable state law, Enerwave shall not be liable to

the purchaser or end user customer of Enerwave products for direct, indirect, incidental, or consequential damages even if

Enerwave has been advised of the possibility of such damages. Enerwave’s total liability under this or any other warranty,

express or implied, is limited to repair, replacement or refund. Repair, replacement or refund are the sole and exclusive

remedies for breach of warranty or any other legal theory.

Model: ZWN-RSM2-PLUS

Smart Dual Relay Switch Module

0208160044-03

WARNING: Turn the POWER OFF at the circuit breaker before installing the Relay

Read and understand these instructions before installing. This device is intended for installation in accordance with the National Electric Code and local regulations. It is recommended that a qualified electrician performs this installation. Make sure to turn off the circuit breaker or fuse(s)

and make sure power is off before wiring the device. Exercise extreme caution when using Z-Wave devices to control appliances. Operation of the Z-Wave device may be in a different room than the controlled appliance so an unintentional activation may occur if the wrong button on the

remote is pressed. Z-Wave devices can be automatically powered on by programmed events. Unattended or unintentional operation could result in hazardous conditions. Z-Wave enabled devices should never be used to supply power to, control or monitor medical and/or life support

equipment. Use copper wires only.

•Connect the BLACK wire on the relay to the HOT wire.

•Connect the WHITE wire on the relay to the NEUTRAL wire.

•Connect the Red "Load 1" wire on the relay to the LOAD wire.

•Connect the ORANGE "Aux 1" wire on the relay to one of the

terminal screws on the wall switch.

•Connect the Red "Load 2" wire on the relay to the LOAD wire.

•Connect the BLUE "Aux 2" wire on the relay to one of the

terminal screws on the wall switch.

•Connect the HOT wire to the other terminal screw on the wall

switch.

DESCRIPTION AND FEATURES

The ZWN-RSM2-PLUS utilizes Z-Wave technology to provide full control of the connected

devices from your Internet Browser or Smart Phone App. It is fully compatible with other

Z-Wave devices and can be added to most Z-Wave compliant controllers. This smart

relay can be used to convert a continuous load into a remotely switched load or used in

conjunction with the existing manual switches to add remote operability. For the advanced

users of Z-Wave, the functions can be customized with programming codes.

•Replaces existing relay with a technologically advanced relay that can be manually

controlled with conjoining switches or remotely through the Z-Wave network.

•Preprogrammed and Customizable functions: Set scenes, schedule events (Program ON/

OFF times like a timer), and even turn ON/OFF when a motion or door sensor goes off.

•Compatible with CFL, fluorescent, incandescent, and halogen bulbs.

•Works with existing light switches. NEUTRAL wire required at the relay.

•Low Profile design allows for easy In-Box installation.

•Signal repeater: repeats other connected Z-Wave devices and controllers, therefore

broadening the area of coverage.

INSTALLING Z-WAVE RELAYS

INSTALLATION

Installing a smart Z-Wave relay in conjunction with a standard switch is a simple way to modernize your home by adding programmable lighting control to your smart device. The

ZWN-RSM2-PLUS Smart Relay enables you to add any compatible light to the Z-Wave network. Follow these directions to wire the relay.

If you have trouble identifying the wires, STOP and

consult with an Electrician.

WIRING DIRECTIONS

DO NOT REVERSE THE HOT AND LOAD WIRES.

DOING SO WILL VOID YOUR WARRANTY AND THE RELAY WILL SHORT CIRCUIT.

Step 1. Identify all your wires. Label the wires or draw a diagram of existing wires. Make sure there

is a NEUTRAL, HOT, and LOAD wire where the ZWN-RSM2-PLUS will be installed.

Step 2. Connect the wires according to the Diagram.

REQUIREMENTS

Z-Wave devices require a connection to a compatible hub. Once the device is properly added to

the hub, it can be managed and customized to your needs. Please visit

www.enerwaveautomation.com for a list of compatible hubs. NEUTRAL wire is required.

SPECIFICATIONS

Voltage.............................................................................................120-277VAC, 50/60Hz

Maximum Load..........................................................................................................4A+4A

Operating Temperature....................................................................................... 32-104° F

Z-Wave Frequency.......................................................................................... 908.42 MHz

Range.........................................................................................Up to 150 feet line of sight

........................between the Wireless Controller and the closest Z-Wave receiver module.

FCC COMPLIANCE STATEMENT

FCC Grant of Equipment Authorizations of this device and transmitters installed in this device can be found at FCC website by entering the FCC ID number on the device.

Caution: Changes or modifications not expressly approved by the part responsible for compliance could void the user’s right to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation of the device.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

PLUS

NEW Z-WAVE 500 SERIES FEATURES

−67% improvement in range

−250% more bandwidth

−Three RF channels for improved noise immunity and higher bandwidth

−New Plug-n-Play Network-wide Inclusion feature

−Improved self-healing and fault tolerance with Explorer Frame feature

−Standardized method for Over the Air firmware updates (OTA)

−Improved product information capture for product certification database

−Fully backward compatible

•During the Inclusion/ Exclusion process, the Program Button on the relay or the ON/OFF toggle

on the switch can be used for including/ excluding the device.

oWhen using the ON/OFF toggle, the toggle must be toggled ON and OFF 3 times.

•It is best to perform an Exclusion of the device prior to performing an Inclusion.

Step 1. From the Control Panel, go the the device Exclusion page.

oSelect "Exclude Device".

oWhen prompted, press the Program Button on the Relay once or toggle the ON/OFF switch 3 times.

Step 2. Go to the "Add Device" page.

oSelect "Include Device".

oWhen prompted, press the Program Button on the Relay once or toggle the ON/OFF switch 3 times.

Push button on the controller will respond to ALL-ON and the ALL-OFF command (default).

Push button on the controller will not respond to ALL-ON or ALL-OFF commands.

Push button on the controller will respond to the ALL-OFF command but will not respond to the ALL-ON command.

Push button on the controller will respond to the ALL-ON command but will not respond to the ALL-OFF command.

PROGRAMMING

ZWN-RSM2-PLUS

WIRELESS RANGE

This device complies with the Z-Wave standard of open-air, line of sight transmission distances of 100 feet.

Actual performance in a home depends on the numbers of walls between the remote controller and the

destination device, the type of construction and the number of Z-Wave enabled devices installed in the control

network. Most Z-Wave enabled devices act as signal repeater and multiple devices result in more possible

transmission routes which helps eliminate " RF dead-spots." Use the following chart only as a guide to

maximize the signal range.

DEVICE INCLUSION/ EXCLUSION

The process of "Inclusion/ Exclusion" is to Add or Remove the device from the Hub. All Z-Wave devices must be "Included"

on the Controller (Hub) before it can be controlled from a smart device. The Hub should be brought physically closer to the

device just for the "Inclusion" process (recommended within 10ft). When finished, the Hub and device can be moved back to

final installation location. Download the App or log onto the website associated with the Hub you are using and follow their

Inclusion/ Exclusion instructions as each Hub's programming and features are different.

ADVANCED PROGRAMMING

WARNING: Advanced programming is recommended ONLY for experienced programmers. The ZWN-RSM2-PLUS has customizable features/ functions that require writing codes. Changes to

code may cause device to function improperly or to not function at all.

The following parameters require that you have an advanced controller. Basic remotes do not have this capability.

All-ON and All-OFF

Depending upon your primary controller, the ZWN-RSM2-PLUS can be set to respond to ALL-ON and ALL-OFF commands in four different ways. Some controllers may not be able to change

the response from its default setting. Please refer to your controller’s instructions or technical support for information on whether or not it supports the configuration function and if so, how to