Enji Happy Care TH-65 Manuale utente
ENJI THERMOMETER TH-65
QUICK GUIDE
FIGURE 1
NOTE:
When you power on the unit, if the measured temperature is less than 32oC
or 90oF, the LCD will display ‘Lo’, if the measured temperature is higher than
42.9oC or 109.9oF, the LCD will display ‘Hi’. So, it is not about the battery
being low.
oF/oC CONVERSION:
Temperature readings are available in the Fahrenheit or Celsius scale (oF/oC;
located in the upper right corner of LCD). With the unit off, press and hold
On/Off Button for approximately 2 seconds to change the current setting.
HOW TO USE:
1. Wipe or dip thermometer probe with isopropyl rubbing alcohol to
disinfect or you may use probe cover.
2. Press the ON/OFF button next to LCD display. A very delicate tone
will sound and the screen will show the self-testing display followed
by the last recorded temperature. Your thermometer is now ready
to use.
3. Position thermometer in desired location (mouth, rectum or
armpit).
a. ORAL USE –Place thermometer under tongue as
indicated by “ , “ position shown in Figure 2. Close your
mouth and breathe evenly through the nose to prevent
the measurement from being influenced by
inhaled/exhaled air. Normal temperature between
35.7oC and 37.3oC (96.3oF and 99.1oF) Figure 2.
b. RECTAL USE –Lubricate the silver probe tip with
petroleum jelly for easy insertion or you use a probe
cover. Gently insert sensor approximately 1cm (less than
1/2”) into rectum. Normal temperature between 36.2oC
and 37.7oC (97.2oF and 99.9oF).
c. ARMPIT USE –Wipe armpit dry. Place probe in armpit
and keep arm pressed firmly at side. From a medical
viewpoint, this method will always provide inaccurate
readings, and should not be used if precise
measurements are required. Normal temperature
between 35.2oC and 36.7oC (95.4oF and 98.1oF).
4. The degree sign flashes throughout the testing process for
approximately 10 seconds depending on the place where you are
taking the measurement (Oral, Rectal, Armpit). When flashing
stops you have your measurement and a very soft alarm will beep,
the measured reading will appear on LCD simultaneously. The
displayed temperature will not change when thermometer is
removed from its testing position.
How to Calibrate your thermometer:
The thermometer is initially calibrated at the time of manufacturing. If the
thermometer is used according to the manual, periodic readjustment is not
required. However, we recommend conducting a quick calibration to confirm
that your unit didn't get damaged during shipment. A quick way to calibrate
your unit is by doing the water test. Dip the tip of the thermometer into a cup
of cold water for a few seconds. Your display should show 'Lo' (meaning low
temperature, not low battery) or a low-temperature reading number (for
example it shows 33 °C or 91°F). Power it OFF then let it sit for two minutes
or three, power it ON, dip the tip into a cup of hot water this time for a few
seconds. Wait for your thermometer to show 'Hi' or a high-temperature
reading number on its LCD display (for example it shows 38 °C or 100 °F).
Power it OFF, Leave it at room temperature for 30 to 45 minutes and start
using it, and it will mean that you have successfully checked your
thermometer and that you are good to go! If you find that your reading is
very low and/or not changing the display of the number on the LCD screen at
all, please get in touch with us through email with your Amazon Order ID.
Do not forget to extend your warranty
by registering your product on our website:
www.enji-prime.com
For more info, email us at,
or visit: www.enji-prime.com
Enji Prime. Copyright 2020
Indice
Altri manuali Enji Termometro
