Entron EN7000-TS Manuale utente



EN7000-TS

Touch-screen programming

User Guide

This user guide demonstrates the use of the EN7000 touchscreen. Reference the

EN7000 Technical Manual for further details of parameters.

Forfirmwareversion1.12

Documentrevision1



2|Page



Contents

Page

Section 1

How to use the Touch Screen……..3

Section 2

Editing Parameters…………………..6

Section 3

Menus…………………………………..8

Section 4

Quick Start……………………..…….39

Section 1 – How to use the touch-screen



3|Page



Note: Not all parameters are visible at any one time. Many parameters are

dependent on other parameters. Only relevant parameters are displayed

as this reduces clutter on the screen. The screens shown here are typical

and may not be exactly what you will see.

1.1 Start-up

On Start-up, the display will show the splash screen.

 Proceed to the Main Menu by tapping the Home icon (bottom right).

Section 1 – How to use the touch-screen



4|Page



1.2 Menu screen

The items described below are common to every menu screen.

UseProgram

DiscreteI/O ˄

HistoryLog System ˅

Program BusI/O

Electrode AnalogI/O

MainMenu

1 Tapping the i in the center of the banner will display the Status screen.

Tappin

it from the Status screen will return to the previous screen.

2 Tappin

the Home icon will return to the previous screen.

3 Tappin

the UP ar

ow scrolls the displa

up one line at a time.

4 The size of the scroll bar handle indicates how many additional items

there are in the menu. The smaller the handle, the more items there are

in the entire menu to be displa

ed.

5 Tapping the blue area in the scroll bar will scroll the display up or down

one pa

e at a time.

6 Tappin

the DOWN arrow scrolls the displa

down one line at a time.

The remaining area is divided up into eight labeled buttons. Tapping one of these

buttons will either

 Open the sub-menu for that function.

 Open an information window.

 If the button contains a parameter, edit that parameter.

Section 1 – How to use the touch-screen



5|Page



1.3 Status screen

This screen presents useful information regarding the status of the control and

the measurements from the last weld. Access the Status screen by tapping on

the i icon on the banner of any menu.

Pos t‐he a t

Progra m 2

Force 100lb

Ready

Conducti o

35.5%

2.00kA

5.00kA

1.00kA

Pre‐heat

Ma i nHe a t

Status

1 This field displays the control status. Tapping on this field will display

a messa

e screen

ivin

the option to reset the status.

2 Pre-heat current from the last weld

3 Main heat current from the last weld

4 Post-heat current from the last weld (Extended Features must be

enabled in the Confi

uration menu

)

5 Pro

ram used for the last weld

6 Force measured from the last weld

7 Percent Conduction of the SCR from the last weld

 Tap the i in the center of the banner to return to the previous screen.

 Tap the HOME key to go to the main menu

Section 2 – Editing parameters

6|Page



Parameters can be edited in several different ways, depending upon their nature.

2.1 Numeric

When you tap on a button showing a numeric parameter, an editor window

opens:

e.g.

1 Present value of paramete

2 Use the ke

pad to enter a new value

3 Cancel the entr

(

present value remains unchan

)

4 Backspace the value in field 1

5 Enter the selected value

(

parameter is chan

ed to new value

)

 Initially, the present value is shown. In the above example the parameter

called Use Program is set to the value 2.

 Tap on the numeric buttons to enter a new value, then tap the green tick

key. The editor will close and return to the previous screen, showing the new

value entered.

 If you enter an illegal value, a warning message appears and the parameter is

not changed. Close the warning message by taping on the red X key in the

top right corner.

Section 2 – Editing parameters

7|Page



2.2 Radio button

This type of parameter has only two options.

e.g.

Standard Extended

Features

 The presently selected option is highlighted. In the above example the

parameter called Features is set to Standard.

 Each time you tap on the button, the parameter is set to the other option.

2.3 Multi-option

This type of parameter has more than two options.

e.g.

I/OSource

DISCRETE

 The presently selected option is shown. In the above example the parameter

called I/O source is set to DISCRETE.

 Each time you tap on the button the parameter will change to the next option

in the list. After the final option, the list starts again with the first option.

2.4 Check box

This type of parameter is either on (box ticked) or off (box clear).

e.g.

Stop

onFault

 In the above example the parameter called ‘Stop on fault’ is on.

 Each time you tap on the button the parameter toggles between on (box

ticked) and off (box clear).

Section 3 – Menus

8|Page



This section describes the hierarchy of menus which allow access to the parameters.

Not all parameters are visible at any one time. Many parameters are dependent on

other parameters. Only relevant parameters are displayed as this reduces clutter on the

screen. The screens shown here are typical and may not be exactly what you will see.

Wherever you see the symbol in this section, this indicates that the

parameter is only available if Extended features is selected in the Configure menu.

The Main menu is the hub from which all sub-menus are accessed.

DiscreteI/O

BusI/O

AnalogI/O

System

Configure

Electrode

HistoryLog

UseProgram

Program

MainMenu

Extended

Section 3 – Menus

9|Page



3.1 Use Program (parameter)

Sets the program number selected to execute when the START signal is applied.

This parameter will not be available if the configuration parameter Program

select is set to Extern.

3.2 Program menu

The Program menu is used to configure parameters in a weld schedule. There

are settings in the Options and Configuration menus that will determine which

of these parameters are displayed.

Program

Time ˄

Current Force

Valves Options

Copy START

Linktoprogram

Electrode

Programmenu

3.2.1. Program (parameter)

Select the program to edit. Subsequent program parameter edits will

apply only to the program set here.

3.2.2. Link to Program (parameter)

Select the program to link to the program being edited. Linking must be

enabled in the Options menu for this field to be displayed. The linked

program will automatically begin after the program being edited executes if

the START signal is maintained.

3.2.3. Electrode (parameter)

Select the electrode to be assigned to the program being edited. Multi

Electrodes must be selected in the Configuration menu.

Extended

Section 3 – Menus

10|Page



3.2.4. Timing menu

50~

Hold

Pre‐heat

10~20~

Squeeze

Upslope

2~

Cool2

Downslope

2~

20~

Post‐heat

20~

Cool1

2~

MainHeat

30~

Timing:Program 0

3.2.4.1. Presqueeze (parameter)

Time interval between program initiation and the start of squeeze

time. Only occurs on the first spot of a Repeat mode spot

sequence. Used to allow for large initial movements of the welding

electrodes.

3.2.4.2. Squeeze (parameter)

Time interval between end of Presqueeze time and the application

of weld current. Used to allow the electrodes to develop the desired

force.

3.2.4.3. Pre-heat (parameter)

Time interval where the Pre-heat current is applied. Pre-heat must

be enabled in the Program Options menu.

3.2.4.4. Cool1 (parameter)

Time interval between end of Pre-heat time and start of Upslope

time where no current is passed. Pre-heat must be enabled in the

Program Options menu to use this feature.

3.2.4.5. Upslope (parameter)

Time interval for the welding current to change from the Pre-heat

value to the Main Heat value.

Altri manuali per EN7000-TS

Indice

Altri manuali Entron Schermo tattile

Entron

Entron EN7000-TS Manuale utente

Manuali Schermo tattile popolari di altre marche

Elecro Engineering

Elecro Engineering Poolsmart Plus Istruzioni per l'installazione

Johnson Controls

Johnson Controls IQ4 HUB Manuale utente

Elo TouchSystems

Elo TouchSystems ET2270L Manuale utente

Elo TouchSystems

Elo TouchSystems ET1002L Manuale utente

Elo TouchSystems

Elo TouchSystems 3201L Manuale utente

Duratec

Duratec S15 Manuale utente

Crestron

Crestron TPMC-3SM Manuale utente

Racelogic

Racelogic MFD Touch Manuale utente

J2 580 Guida utente

HAI

HAI OmniTouch 10p Manuale utente

panel

panel PC PSR108-FM Series Manuale utente

Tipro

Tipro FREE+ Manuale utente

Systemline

Systemline Commander Manuale utente

Interactive Technologies

Interactive Technologies Insite Manuale utente

GVision

GVision Legacy Manuale utente

BeiJer

BeiJer T21C-C24 Manuale utente

Advantech

Advantech ITM-5117 Series Manuale utente

Edge

Edge CS Manuale utente