EP Solar LS1024R Manuale utente

LS1024R / LS1524R / LS2024R

—— Solar Light Controller

Thank you very much for selecting our product!

This manual offers important information and

suggestions with respect to installation, use and

troubleshooting, etc. Please read this manual

carefully before using the product and pay attention

to the safety recommendations in it.

EPSOLAR

☆Design patent NO.：

201130028317.3

☆Utility model patent NO.：

201120064092.1

INSTRUCTION

MANUAL

LS1024R / LS1524R / LS2024R

—— Solar Light Controller

Installation and Operation Manual

Specification Summary

Nominal system voltage 12 / 24VDC*

Maximum PV input voltage 50V

Nominal charge / discharge current

LS1024R 10A

LS1524R 15A

LS2024R 20A

* The controller will recognize the system rated voltage when start up. If

the battery voltage is lower than 18V, it will recognize the system as 12V.

If the battery voltage is greater than 18V, it will recognize the system as

24V.

LandStar

Contents

1 Important Safety Information.....................................1

2 General Information...................................................2

2.1 Product Overview................................................2

2.2 Product Features..................................................3

3 Installation Instructions..............................................4

3.1 General Installation Notes ...................................4

3.2 Mounting.............................................................4

3.3 Wiring.................................................................6

4 Operation..................................................................10

4.1 PWM Technology .............................................10

4.2 Battery Charging Information............................10

4.3 LED Indicators..................................................12

4.4 Setting Operation...............................................14

5 Protections, Troubleshooting and Maintenance........18

5.1 Protection ..........................................................18

5.2 Troubleshooting ...............................................19

5.3 Maintenance ..................................................21

6 Warranty ..................................................................22

7 Technical Specifications...........................................23

1 Important Safety Information

Save These Instructions

This manual contains important safety, installation and operating

instructions.

The following symbols are used throughout this manual to indicate

potentially dangerous conditions or mark important safety instructions，

please take care when meeting these symbols.

WARNING: Indicates a potentially dangerous

condition. Use extreme caution when

performing this task.

CAUTION: Indicates a critical procedure for

safe and proper operation of the controller.

NOTE: Indicates a procedure or function that

is important for the safe and proper operation

of the controller.

General Safety Information

Read all of the instructions and cautions in the manual before beginning

installation.

There are no user serviceable parts inside the controller. Do not

disassemble or attempt to repair it.

Install external fuses/breakers as required.

Disconnect the solar module and fuse/breakers near to battery before

installing or adjusting the controller.

Do not allow water to enter the controller.

Confirm that power connections are tightened to avoid excessive heating

from loose connection.

2 General Information

2.1 Product Overview

Thank you for selecting LandStar series solar light controller that adopts the

most advanced digital technique and operates fully automatically. The Pulse

Width Modulation (PWM) battery charging can greatly increase the lifetime

of battery. It has various unique functions and quite easy to use, such as:

12/24V automatic recognition

High efficient Series PWM charging, increase the battery lifetime and

improve the solar system performance.

Use MOSFET as electronic switch, without any mechanical switch

Widely used, automatically recognize day/night.

Digital LED menu, only one key solve all setting simply

Intelligent timer function with 1-15 hours option

Unique dual timer function, enhance the flexibility of street light system.

Gel, Sealed and Flooded battery type option.

Adopt temperature compensation, correct the charging and discharging

parameters automatically and improve the battery lifetime.

Electronic protection: Overheating, over charging, over discharging,

overload, and short circuit.

Reverse protection: any combination of solar module and battery.

The controller is for off-grid solar system, especially in solar light system,

and protects the battery from being over charged by the solar module and

over discharged by the loads. The charging process has been optimized for

long battery life and improved system performance. The comprehensive

self-diagnostics and electronic protection functions can prevent damage from

installation mistakes or system faults.

Though the controller is easy to operate and use, please take your time to

read this manual and become familiar with it. This will help you make full

use of all the functions and improve your solar PV system.

2.2 Product Features

Figure 2-1 Land Star characteristics

1 –Temperature Sensor

Measure ambient temperature and make temperature compensation for

charging and discharging.

2 –Charging status LED indicator

An LED indicator that shows charging status and also indicates when a solar

input fault condition exists

3 –Battery status LED indicator

An LED indicator that shows battery status

4 –Battery type setting indicator

The indicator will be on when select battery type.

5 –Timer 2 setting indicator

The indicator will be on when set timer 2.

6 –Timer 1 setting indicator

The indicator will be on when set timer 1.

7 –LED digital display

Display the load work mode and status

8 –Setting button (in manual mode used for load ON/OFF)

Set load work mode and select battery type.

9 –Solar Module Terminals

Connect solar modules.

10 –Battery Terminals

Connect batteries.

11 –Load Terminals

Connect loads.

3 Installation Instructions

3.1 General Installation Notes

Read through the entire installation section first before beginning installation.

Be very careful when working with batteries. Wear eye protection. Have

fresh water available to wash and clean any contact with battery acid.

Uses insulated tools and avoid placing metal objects near the batteries.

Explosive battery gasses may be present during charging. Be certain there

is sufficient ventilation to release the gasses.

Avoid direct sunlight and do not install in locations where water can enter

the controller.

Loose power connections and/or corroded wires may result in resistive

connections that melt wire insulation, burn surrounding materials, or even

cause fire. Ensure tight connections and use cable clamps to secure cables

and prevent them from swaying in mobile applications.

Use with Gel, Sealed or Flooded batteries only.

Battery connection may be wired to one battery or a bank of batteries. The

following instructions refer to a singular battery, but it is implied that the

battery connection can be made to either one battery or a group of

batteries in a battery bank.

Select the system cables according to 3A/mm2current density

3.2 Mounting

NOTE: When mounting the controller, ensure free air

through the controller heat sink fins. There should be at

least 6 inches (150 mm) of clearance above and below the

controller to allow for cooling. If mounted in an

enclosure, ventilation is highly recommended.

WARNING: Risk of explosion! Never install the

controller in a sealed enclose with flooded batteries! Do

not install in a confined area where battery gassed can

accumulate.

Step 1: Choose Mounting Location

Locate the controller on a vertical surface protected from direct sun, high

temperature, and water. And make sure good ventilation.

Step 2: Check for clearance

Place the controller in the location where it will be mounted. Verify that

there is sufficient room to run wires and that there is sufficient room above

and below the controller for air flow.

Figure 3-1 Mounting and cooling

Step 3: Mark Holes

Use a pencil or pen to mark the four (4) mounting hole locations on the

mounting surface.

Step 4: Drill Holes

Remove the controller and drill 4.5mm holes in the marked locations.

Step 5: Secure Controller

Place the controller on the surface and align the mounting holes with the

drilled holes in step 4.

Secure the controller in place using the mounting screws.

Warm air

Cool air

150mm(5.9inches)

3.3 Wiring

NOTE: A recommended connection order has been

provided for maximum safety during installation.

NOTE: The controller is a common positive ground

controller.

CAUTION: Donʼt connect the loads with surge power

exceeding the ratings of the controller.

CAUTION: For mobile applications, be sure to secure

all wiring. Use cable clamps to prevent cables from

swaying when the vehicle is in motion. Unsecured

cables create loose and resistive connections which may

lead to excessive heating and/or fire.

Step1: Battery Wiring

WARNING: Risk of explosion or fire! Never short

circuit battery positive (+) and negative (-) or cables

Figure 3-2 Battery connecting

Battery

150mm(5.9inches)

MAX

Fuse

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali EP Solar Controllori

EP Solar

EP Solar LS2024B Manuale utente

EP Solar

EP Solar EPHC Series Manuale utente

EP Solar

EP Solar SS1024R Manuale utente

EP Solar

EP Solar Tracer-4210RN Manuale utente

EP Solar

EP Solar LS1024 Manuale utente

EP Solar

EP Solar LS1024RD Manuale utente

EP Solar

EP Solar ET2415N Manuale utente

EP Solar

EP Solar LS1024BP Manuale utente

EP Solar

EP Solar ViewStar Series Manuale utente

EP Solar

EP Solar EPIPDB-COM series Manuale utente

EP Solar

EP Solar LandStar LS-EU Series Manuale utente

EP Solar

EP Solar EPIP20-LT Series Manuale utente

EP Solar

EP Solar LandStar LS0524R Manuale utente

EP Solar

EP Solar ViewStar MT-100 Manuale utente

EP Solar

EP Solar EPHC10-EC series Manuale utente

EP Solar

EP Solar eTracer ET4415BND Manuale utente

EP Solar

EP Solar Tracer1215BN Manuale utente

EP Solar

EP Solar LS0512R Manuale utente

EP Solar

EP Solar EPRC10-EC Manuale utente

EP Solar

EP Solar Tracer-2210RN Manuale utente

EP Solar

EP Solar LS1024RPD Manuale utente

EP Solar

EP Solar Tracer-1206RN Manuale utente

EP Solar

EP Solar Tracer-3215RN Manuale utente

EP Solar

EP Solar eTracer Series Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente