Epilog Laser FiberMark Manuale utente

EPILOG LASER

16371 Table Mountain Parkway

Golden, Colorado 80403

Phone 303-215-9171 - FAX 303-277-9669

www.epiloglaser.com

Machine Type: Fibermark

Procedure: Replacing the Encoder strip

Tools Required: Small tip screw driver

1. Turn off the engraver and disconnect it from its power

source.

2. Open the access window.

3. Move the X-axis assembly to the center of the engraver.

4. Loosen, but do not remove the seven screws, two on the

front and five on the rear, which secure the yellow x-

axis cover. Remove the cover and set it to one side.

5. Directly behind the lens carriage is the Encoder reader

assembly. Attached to the encoder reader is a white

ribbon cable. Remove the cable by depressing the clip

and pulling the connector to the left.

6. The Encoder reader needs to be removed. The reader can

be removed by removing the 3/32 Allen screws which

secure the board to the lens carriage.

7. The encoder strip is the clear piece of plastic about

the thickness of a sheet of paper that sits vertically

in the x-axis assembly as shown in picture 1

Picture 1

8. Pull the x-axis assembly to the front of the engraver.

The screws which secure the encoder strip are only

accessible from the rear of the rail.

9. Remove the 13 screws which secure the Encoder strip and

the Encoder strip support (this is the small aluminum

bar that is between the screws and the Encoder strip

itself.

10.Installing a new encoder strip is very simple, When

standing in front of the machine the text on the encoder

strip should face so it is upside down and backwards, or

to where the text if facing the back of the machine.

11.Line up the screw holes on both the Encoder strip and

the encoder strip support and loosely install the 13

screws that were removed earlier. Once all 13 screws are

installed, go back and tighten the screws.

12.Re-install the encoder reader with the 3/32 Allen screws

making sure that the encoder reader straddles the

encoder strip. If the reader does not straddle the

encoder strip, the x-axis will slam when the machine is

restarted.

13.Re-connect the white ribbon cable to the Encoder reader

assembly.

14.Replace the x-axis cover.

15.Reconnect the engraver to its power source.

This completes changing the encoder strip in your FiberMark

laser engraver.

If you have any questions please call Epilog’s Technical Support

Phone 303.215.9171

Fax 303.531.7594

E-Mail: tech@epiloglaser.com

Altri manuali per FiberMark

5

Indice

Altri manuali Epilog Laser Incisore

Epilog Laser

Epilog Laser MINI 18 Manuale utente

Epilog Laser

Epilog Laser Fusion Manuale utente

Epilog Laser

Epilog Laser Fusion Manuale utente

Epilog Laser

Epilog Laser Fusion Manuale utente

Epilog Laser

Epilog Laser Fusion Manuale utente

Epilog Laser

Epilog Laser Zing Manuale utente

Epilog Laser

Epilog Laser Helix Manuale utente

Epilog Laser

Epilog Laser FiberMark Manuale utente

Epilog Laser

Epilog Laser MINI Manuale utente

Epilog Laser

Epilog Laser FiberMark Manuale utente

Epilog Laser

Epilog Laser Zing Manuale utente

Epilog Laser

Epilog Laser Zing Manuale utente

Epilog Laser

Epilog Laser MINI Manuale utente

Epilog Laser

Epilog Laser Edge 12 Manuale utente

Epilog Laser

Epilog Laser FiberMark Fusion 13000 Manuale utente

Epilog Laser

Epilog Laser MINI Manuale utente

Epilog Laser

Epilog Laser LEGEND 24EX 6000 Manuale utente

Epilog Laser

Epilog Laser Fusion Manuale utente

Epilog Laser

Epilog Laser Fusion Pro 32 Manuale utente

Epilog Laser

Epilog Laser Fusion Pro 32 Manuale utente

Epilog Laser

Epilog Laser Fusion Manuale utente

Epilog Laser

Epilog Laser Helix Manuale utente

Epilog Laser

Epilog Laser Fusion Pro 32 Manuale utente

Epilog Laser

Epilog Laser Helix Manuale di installazione e funzionamento

Manuali Incisore popolari di altre marche

COMGROW

COMGROW COMGO Z1 Manuale utente

BAUKER

BAUKER EG013 Manuale utente

GRAVOGRAPH

GRAVOGRAPH LS900 XP Istruzioni operative

iMARC

iMARC VET TAG Engraver Manuale utente

Dremel

Dremel 3000 Operating/s Manuale utente

iMARC

iMARC Pet Tag Engraver Manuale utente

PT

PT W50036 Manuale utente

Omtech

Omtech USB3020A Manuale utente

Ortur

Ortur Laser Master 2 Manuale utente

Vision

Vision VE-810 Manuale utente

Omtech

Omtech POLAR 350 Manuale utente

Vision

Vision Cylindrical Manuale utente

SCULPFUN

SCULPFUN S6 Manuale utente

Redsail

Redsail M500 Guida rapida alla configurazione

Dremel

Dremel 290 Istruzioni per il montaggio

Vision

Vision MaxPro Manuale utente

Vision

Vision 5 Series Manuale utente

SFX

SFX SFX-GS Manuale utente