Epilog Laser MINI Manuale utente

Epilog Laser Tube Upgrade

Mini / Helix

Revision Date: 9/27/2013 pg. 1 of 17

EPILOG LASER

16371 Table Mountain Parkway

Golden, Colorado 80403

Phone 303-215-9171

FAX 303-277-9669

www.epiloglaser.com

Epilog Laser Tube Upgrade

For the Epilog Mini / Helix

9/27/2013

Requirements:

Tools:

•Phillips Head Screwdriver

•Set of SAE (US Sized) Allen Keys

•Locking Pliers

•Nut Driver / Wrench (5/16”)

Parts:

•Epilog Replacement Laser Tube

•Adapter Bracket (MT266)

•Fans (optional)

•PSU Bracket (optional)

•Rear Panel (optional)

Overview:

This document details the process to upgrade your laser with an Epilog Laser

Tube.

Epilog Laser Tube Upgrade

Mini / Helix

Revision Date: 9/27/2013 pg. 2 of 17

Procedure A: Removing the Old Laser Tube

Step 1:

Be sure that the engraver is powered off and unplugged. Remove the rear panel

of the engraver to expose the laser tube.

Step 2:

Disconnect the Red Dot Pointer which is located on the right side of the laser

tube. Follow the thin Red and White wires to the Black Connector. Unplug the

connector.

Epilog Laser Tube Upgrade

Mini / Helix

Revision Date: 9/27/2013 pg. 3 of 17

Step 3:

Disconnect the Grey Data Cable from the Left side of the laser tube.

Step 4:

Disconnect the Red and Black Power Harness. Follow the power Wires to the

White Connector and unplug the connector.

Epilog Laser Tube Upgrade

Mini / Helix

Revision Date: 9/27/2013 pg. 4 of 17

Step 5:

Locate and unscrew the three (3) green thumb screws with a Philips Head Screw

Driver. Please note that the screws are captive and will not come completely out of the

bracket.

Step 6:

Slide the laser tube to the left. The entire unit will slide up to a half an inch

(12mm).

Step 7:

You may now carefully lift the laser tube up and out of the engraver and place it

on a flat table.

CAUTION: The laser tube can weigh between 10 and 20 lbs. (4.5 to 9 kg).

Please take proper precautions when lifting heavy objects.

Epilog Laser Tube Upgrade

Mini / Helix

Revision Date: 9/27/2013 pg. 5 of 17

Procedure B: Installing Adapter Bracket

Step 1:

Locate the left hand shoulder screw and remove it by unscrewing it. When

finished please discard the shoulder screw.

Step 2:

Locate the left hand spacing standoff. Using a pair of Locking Pliers, break the

standoff away from the body of the engraver. You will not damage the Engraver.

Epilog Laser Tube Upgrade

Mini / Helix

Revision Date: 9/27/2013 pg. 6 of 17

Step 3:

Locate the MT266 adapter bracket that came with the upgrade kit.

Step 4:

Install the new Shoulder Screw and washer (that came packaged with the

MT266) into the top left hand corner of the MT266 Adapter Bracket.

Step 5:

Align the two screw holes on the right hand side of the adapter bracket, with the

screw holes on the engraver. Fasten with the provided screws.

Epilog Laser Tube Upgrade

Mini / Helix

Revision Date: 9/27/2013 pg. 7 of 17

Procedure C: Installing the new fans.

This procedure is for the Mini 24 and Helix machines only. If you currently have 4 fans but space for 6,

please follow this procedure. If you currently have 6 fans or if you own a Mini 18 you can skip this

procedure. Please contact Epilog Technical Support if you need assistance.

Step 1:

Locate the Fan Tray inside of the engraver.

Step 2:

Locate and unplug the Fan Wire Harness. The wire harness is on the left side of

the Fan Tray.

Epilog Laser Tube Upgrade

Mini / Helix

Revision Date: 9/27/2013 pg. 8 of 17

Step 3:

Remove the Wire Harness holder.

Step 4:

Remove the fan tray by locating and removing the nuts on the left and right sides

of the tray.

Step 5:

Insert the new fan tray into the engraver and fasten with the nuts.

Epilog Laser Tube Upgrade

Mini / Helix

Revision Date: 9/27/2013 pg. 9 of 17

Step 5:

Connect the fan Wire Harness. And fasten with holder.

Epilog Laser Tube Upgrade

Mini / Helix

Revision Date: 9/27/2013 pg. 10 of 17

Procedure D: Installing the new PSU Bracket.

In some cases the engraver’s Power Supply Unit (PSU) will need to be rotated to accommodate the new

laser tube. This procedure illustrates the process to rotate the PSU and install a new mounting bracket.

This procedure is only for engravers with the Power Supply Unit (PSU) illustrated in Figure A. If your

engraver has a power supply unit matching Figure B or Figure C than you may skip this procedure.

Please contact Epilog Technical Support if you need assistance.

Figure A: Silver PSU

(Label facing out)

Follow this procedure.

Figure B: Silver PSU

(Label facing up)

Skip this procedure.

Figure C: Black PSU

Skip this procedure.

The Power Supply Unit (PSU) may contain hazardous electrical current. Please exercise caution any time

you work with Mains power. Be sure that the engraver is Powered Off and Unplugged before starting

work on the PSU. Do not touch Electrical Contacts, Leads, or Damaged Wires with your bare hands

while performing this procedure. Do not attempt to open the PSU’s housing.

Electrical charge may still be present in the PSU even after it has been disconnected.

Altri manuali per MINI

Questo manuale è adatto per i seguenti modelli

Altri manuali Epilog Laser Incisore

Epilog Laser

Epilog Laser Helix Manuale di installazione e funzionamento

Epilog Laser

Epilog Laser Fusion Manuale utente

Epilog Laser

Epilog Laser Zing Manuale utente

Epilog Laser

Epilog Laser Fusion Manuale per l'uso e la cura

Epilog Laser

Epilog Laser MINI 18 Manuale utente

Epilog Laser

Epilog Laser Fusion Manuale utente

Epilog Laser

Epilog Laser Fusion Pro 32 Manuale utente

Epilog Laser

Epilog Laser Fusion Manuale utente

Epilog Laser

Epilog Laser FiberMark Manuale utente

Epilog Laser

Epilog Laser Zing Manuale utente

Epilog Laser

Epilog Laser LEGEND 24EX 6000 Manuale utente

Epilog Laser

Epilog Laser Fusion Pro 32 Manuale utente

Epilog Laser

Epilog Laser Fusion Manuale utente

Epilog Laser

Epilog Laser FiberMark Manuale utente

Epilog Laser

Epilog Laser FiberMark Fusion 13000 Manuale utente

Epilog Laser

Epilog Laser MINI Manuale utente

Epilog Laser

Epilog Laser Edge 12 Manuale utente

Epilog Laser

Epilog Laser FiberMark Manuale utente

Epilog Laser

Epilog Laser Fusion Manuale utente

Epilog Laser

Epilog Laser Fusion Pro 32 Manuale utente

Epilog Laser

Epilog Laser Fusion Pro 32 Manuale utente

Epilog Laser

Epilog Laser Fusion M2 32 Manuale utente

Epilog Laser

Epilog Laser MINI Manuale utente

Epilog Laser

Epilog Laser Fusion Manuale utente

Manuali Incisore popolari di altre marche

COMGROW

COMGROW COMGO Z1 Manuale utente

BAUKER

BAUKER EG013 Manuale utente

GRAVOGRAPH

GRAVOGRAPH LS900 XP Istruzioni operative

iMARC

iMARC VET TAG Engraver Manuale utente

Dremel

Dremel 3000 Operating/s Manuale utente

iMARC

iMARC Pet Tag Engraver Manuale utente

PT W50036 Manuale utente

Omtech

Omtech USB3020A Manuale utente

Ortur

Ortur Laser Master 2 Manuale utente

Vision

Vision VE-810 Manuale utente

Omtech

Omtech POLAR 350 Manuale utente

Vision

Vision Cylindrical Manuale utente

SCULPFUN

SCULPFUN S6 Manuale utente

Redsail

Redsail M500 Guida rapida alla configurazione

Dremel

Dremel 290 Istruzioni per il montaggio

Vision

Vision MaxPro Manuale utente

Vision

Vision 5 Series Manuale utente

SFX

SFX SFX-GS Manuale utente