E+E Elektronik EE650 Manuale utente

GENERAL

The EE650 transmitter is designed for accurate measurement of air velocity in HVAC. It operates on the hot-film anemometer prin-

ciple and features the innovative, very robust E+E VTQ sensing element manufactured in thin-film technology combined with state-

of-the-art transfer molding.

The construction of the sensing head leads to a very low angular dependence which facilitate the installation. The mounting flange

allows for easy adjustment of the immersion depth.

The measuring range and the response time of EE650 can be selected with jumpers on the electronics board, see below

“Settings”.

EE650 is dedicated for heating, ventilation and air conditioning applications. For special applications do not hesitate to contact the

manufacturer or their local distributor.

CAUTION

• Accurate measurement results are conditioned by the correct positioning of the sensing probe in the air stream. Best accuracy

is achieved in laminar flow.

• Observe the minimum inlet and outlet path length, see page 4.

• Avoid mechanical stress onto the probe and mainly onto the sensing head.

• Observe the humidity working range 5 … 95% RH, non-condensing.

• Avoid installation in corrosive environment, as this may lead to sensor destruction.

SETTINGS

For performing EE650 settings via EE-PCS Product Configuration Software (download from www.epluse.com/configurator) the

working range jumper must be on HI.

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

t90

MED

Jumper t90

SLOW 4 sec.

(factory setting)

Jumper I

CURRENT

(factory setting)

no jumper

FAST 1 sec.

Jumper U

VOLTAGE

Jumper HI

0...20 m/s (0...4000 ft/min)

(factory setting)

Jumper MED

0...15 m/s (0...3000 ft/min)

Jumper LO

0...10 m/s (0...2000 ft/min)

Selection of response time t90

Selection of output signal

Selection of ouput signal

Selection of measuring range

EE650 - Air Velocity Transmitter for HVAC Applications

USER‘S GUIDE

CONNECTING DIAGRAM

GND

V+

V / mA

1 ... V+ = supply voltage

2 ... GND = ground

3 ... AV = analogue output air velocity

Power supply

24 V AC/DC ±20% b ... brown

g ... green

y ... yellow

w ... white

s ... black

s w y g b

Remote sensor probe

TECHNICAL DATA

Measuring range

Working range 1) 0...10 m/s (0...2000 ft/min)

0...15 m/s (0...3000 ft/min)

0...20 m/s (0...4000 ft/min) (factory setting)

Output 1) 0 - 10 V -1 mA < IL< 1 mA

0...10 m/s / 0...15 m/s / 0...20 m/s 4 - 20 mA (factory setting) RL< 500 Ω(linear, 3-wires)

Accuracy at 20 °C (68 °F), 0.2...10 m/s (40...2000 ft/min) ± (0.2 m/s (40 ft/min) + 3 % of m. v.)

45 % RH, 1013 hPa 0.2...15 m/s (40...3000 ft/min) ± (0.2 m/s (40 ft/min) + 3 % of m. v.)

0.2...20 m/s (40...4000 ft/min) ± (0.2 m/s (40 ft/min) + 3 % of m. v.)

Response time τ90

1) 2) typ. 4 sec. (factory setting) or typ. 1 sec. at constant temperature

General

Power supply 24V AC/DC ± 20 %

Current consumption for AC supply max. 170 mA

for DC supply max. 70 mA

Electrical connection screw terminals max. 1.5 mm2 (AWG 16)

Cable gland M16x1.5

Electromagnetic compatibility EN61326-1 EN61326-2-3 ICES-003 ClassB

Industrial Environment FCC Part 15

Housing material Polycarbonate, UL94V-0 approved

Protection class Enclosure IP65 / NEMA 4, remote probe IP20

Temperature range working temperature probe -25 ... +50 °C (-13...122 °F)

working temperature electronic -10 ... +50 °C (14...122 °F)

storage temperature -30 ... +60 °C (-22...140 °F)

Working range humidity 5...95 % RH (non-condensing)

1) Selectable by jumper

2) Response time τ90 is measured from the beginning of a step change of air velocity to the moment of reaching 90% of the step.

DIMENSIONS MM (INCH)

Ø > 16

FOR CONDUIT

INSTALLATION

Cable gland

M16x1,5

~110 or 210

Ø > 13

80,6

101

155

15 155

Cable gland

M16x1,5

Type - Duct mount Mounting flange

Type - Remote sensor probe

CONFIGURATION AND ADJUSTMENT

The EE650 as ordered is ready for use immediately and requires no configuration by the user. If required, the optional E+E Product

Configuration Adapter (EE-PCA) and the E+E Product Configuration Software (EE-PCS) can be used for changing the factory

setup as well as for adjusting of the air velocity measurement. Additionally, it allows for setting the display backlighting and

orientation.



HA011062

EE-PCA

V03

For product data sheets EE-PCS and EE-PCA please see www.epluse.com.

The E+E Product Configuration Software (EE-PCS) is free and can be downloaded from www.epluse.com/configurator.

MOUNTING

DRILLING IN THE WALL OF THE DUCT FOR INSTALLING THE MOUNTING FLANGE

Air flow

>16 (0.63")

60 (2.4")

The arrow engraved on the sensing head of EE650 indicates the direction of the air stream during factory adjustment. When

installing the EE650 probe, make sure that the arrow matches exactly the flow direction.

Air flow

CORRECT INCORRECT

The mounting flange allows for precise setting of the EE650 immersion depth in a duct. The entire sensing head must be in the air

flow to be measured.

Immersion depth = 30 % - 50 %

of the duct diameter

duct diameter

CORRECT INCORRECT

Air flow

POSITIONING OF AIR VELOCITY SENSOR IN A VENTILATION DUCT

The reliable and accurate measurement of air velocity depends on the correct positioning of the sensor in the ventilation duct.

Accurate measurements are only possible if the air velocity probe is positioned at a location with a laminar (to-turbulent) flow.

The required length of the calming section after a fault is a function of the tube diameter D. For a rectangular channel a x b applies:

<6D

>3D

>6D

Mounting the sensing probe in the middle of the

channel.

The optimal position is after the filter.

Please note sufficient distance.

Positioning the probe ahead of diffusor, at a place

with high flow rate.

Positioning the probe at a location with a laminar (to-

turbulent) flow.

Turbulent flows are caused by pipe bends, branches,

behind flaps, flans, air heaters, air coolers or cross-

sectional changes.

MAINTENANCE OF THE E+E AIR VELOCITY TRANSMITTERS

Due to the absence of moving parts, the E+E air velocity transmitters are not subject to wear. The construction (shape, dimensions

and materials) of the hot film air velocity sensor is per se highly insensitive to dust and dirt. No maintenance is required under

normal environmental conditions. For operation in polluted environment it is advisable to periodically clean the sensing head by

washing it in isopropyl alcohol, preferably in an ultrasound cleaner. Alternatively shake it gently few minutes in a pot with isopropyl

alcohol and let it dry free. Do not touch or rub the sensor and do not use any mechanical tools for cleaning.

INFORMATION +43 7235 605 0 / [email protected]

E+E Elektronik Ges.m.b.H.

Langwiesen 7 • A-4209 Engerwitzdorf

Tel: +43 7235 605-0 • Fax: +43 7235 605-8

[email protected] • www.epluse.com

LG Linz Fn 165761 t • UID-Nr. ATU44043101

Place of Jurisdiction: A-4020 Linz • DVR0962759

BA_EE650_e // v1.3 // Modiﬁ cation rights reserved

USA

FCC notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the installation manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CANADIAN

ICES-003 Issue 5:

CAN ICES-3 B / NMB-3 B

SCOPE OF SUPPLY

• EE650 Transmitter according to ordering guide

• Cable gland

• Mounting flange

• Mounting materials

• Protection cap

• Instruction manual

• Two self-adhesive labels for configuration changes (see user guide at www.epluse.com/relabeling)

• Test report according to DIN EN10204 - 2.2

ACCESSORIES

• Product configuration adapter see data sheet EE-PCA

• Product configuration software EE-PCS (free download: www.epluse.com/EE650)

• Power supply adapter V03 (see data sheet Accessories)

Indice

Altri manuali E+E Elektronik Trasmettitore

E+E Elektronik

E+E Elektronik EE31 Manuale utente

E+E Elektronik

E+E Elektronik EE371 Manuale utente

E+E Elektronik

E+E Elektronik EE22 Series Manuale utente

E+E Elektronik

E+E Elektronik EE310 Manuale utente

E+E Elektronik

E+E Elektronik EE210 Manuale utente

E+E Elektronik

E+E Elektronik EE650 Manuale utente

E+E Elektronik

E+E Elektronik EE381 Manuale utente

E+E Elektronik

E+E Elektronik EE06 Series Manuale utente

E+E Elektronik

E+E Elektronik EE23 series Manuale utente

E+E Elektronik

E+E Elektronik EE870 Manuale utente

E+E Elektronik

E+E Elektronik EE360 Manuale utente

E+E Elektronik

E+E Elektronik EE29 Series Manuale utente

E+E Elektronik

E+E Elektronik EE04 Series Istruzioni utente

E+E Elektronik

E+E Elektronik EE310 Manuale utente

E+E Elektronik

E+E Elektronik EE355 Manuale utente

E+E Elektronik

E+E Elektronik EE360 Manuale utente

E+E Elektronik

E+E Elektronik EE65 Series Istruzioni utente

E+E Elektronik

E+E Elektronik EE040 Manuale utente

E+E Elektronik

E+E Elektronik EE210 Manuale utente

E+E Elektronik

E+E Elektronik EE220 Manuale utente

E+E Elektronik

E+E Elektronik EE371 Manuale utente

E+E Elektronik

E+E Elektronik EE375 Series Manuale utente

E+E Elektronik

E+E Elektronik EE150 Manuale utente

E+E Elektronik

E+E Elektronik EE061 Series Manuale di istruzioni

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente