Epson Stylus C63 Manuale utente

Continuous Ink Supply System

for

Epson Stylus C63/C65/C84/C86 Printer

Installation Instruction

For MT Empty Cartridge Version

With Auto Reset Chips

CIS for Epson C63/C65/C84/C86 Instruction

I. What’s in the MT-C63 Continuous Ink Supply system?

1) 4 * 100ml Reservoir Bottles;

2) Tubing Attached with Cartridge and Chips;

3) A set of Support Arm & Black Rubber;

4) 4 * Vacuum Pump (Filling tools).

READ ALL INSTRUCTION PRIOR TO INSTALLING YOUR NEW SYSTEM

Thank you for purchasing MT Continuous Ink Supply System. We appreciate your

support and will try our best to make your experience with our products a pleasant one.

Printing has been a different experience ever since you installed MT Continuous Ink

Supply system on your own printer. Just imagining being able to print without regard to

the ink level in those expensive little cartridges.

Please take your time installing MT Continuous Ink Supply system. Do not remove your

old cartridge until you have the MT CIS system primed and ready to install (to prevent

the drying of heads). In addition, make sure you are getting perfect nozzle checks

before installing the MT CIS system. The MT CIS system won’t be able to work properly

if the nozzles are previously clogged.

Most people get a perfect nozzle check the first time after installing the MT Continuous

Ink Supply system; others may need to run two or three cleaning cycles or let the printer

sit for a while before they get the perfect results.

II. Getting Started

1. Check the printer head before beginning the installation.

1) Open the window of the Computer and find the Control Panel. Then click

“Printer and Other Hardware”

2) Click the right button of mouse on EPSON Stylus C63 Series. Then click the

Properties and choose the “Nozzle Check” as the below picture shown.

3) Using the EPSON Utility, print a “ Nozzle Check” to make sure that all the nozzles

are firing properly.

2. Press the “ink cartridge replace button” (Picture A) on the printer to move the cartridge

to the cartridge remove position (Picture B).

(Picture A) (Picture B)

3. Unplug the power connector at the back of the printer (Picture A). This will prevent the

printer from “auto powering down”, allowing you have as much time as you need to

complete the installation. Remove the cartridges as the below picture B shown.

Then use a small screwdriver to remove the original cover (Picture C)

(Picture A). (Picture B) (Picture C)

4. Open the black cap of the Reservoir bottle and fill ink into it one by one; please pay

attention to the color sticker on the Reservoir Bottles and fill ink according to the

sticker’s color.

1) Pay attention to the direction guide on the Black cap and direction guide on the

Bottles, when the printer is working, make sure the two direction guides are on

the horizontal line to let the air in. In the case of leaking out ink, make them on the

vertical line when the printer stops working.

Stopping Working

2) Roll up the Plastic Valve.

5. Firstly use a needle to poke the film of the cartridge (Picture A); Then insert the vacuum

pump into the holes of Cartridge as the below picture shown and pull the plunger

backward (Picture B); Stop pulling the plunger till ink flows into the vacuum pump;

(Picture A) (Picture B)

6. Measure 13cm from the edge of the printer and make a mark: then tear off the sticker

(Picture A) and attach Support Arm to the printer as the Picture B shows.

(Picture A) (Picture B)

7. Attach the small tube clamp at the right of the printer and Make sure it is parallel with the

Support Arm as the below picture shown.

8. Insert the cartridge into the cartridge carriage after finishing ink-filling; Make sure the

cartridge is down all the way and they are making contact with the fingers that read

chips;

9. Put the Tube into the Support Arm and Small Tube clamp as the below picture shown.

10. Slide the cartridge back and forth from left to right several times; make sure the tubes

not too tight when cartridge is in the far right and left position.

Now everything is put together! Double check your cartridge; then turn on the

power. Watch for anything unusual. You are ready to start printing.

III. Nozzle Check

11. Turn on the power and clean the printer head for two or three times as the following

picture shown.

12. Print the test paper and if the print effect shown as the following picture, you can start

printing.

IV. Auto Reset Procedure

13. When the indicator light on printer shows short of ink and change cartridges (Picture

A); Please turn off the printer for about 30 seconds, then switch it back on. At this

time the Ink meter bar shall show 99% (Picture B). You can start printing as usual.

(Picture A) (Picture B)

P.S: the black rubber is used only in the process of transportation when the reservoir bottles

are full of ink. They are used to avoid ink leakage. In the meantime, you can use it for

propping up the lid of the printer

Notice:

1. Please don’t take out cartridge at random after installing the CIS system. Keep the reservoir

bottles on the same level with the printer.

2. Try to keep at least 1/2 inch of ink in the bottles, as you don’t want to run out of ink and draw

air into the cartridge.

3. Don’t place the Reservoir Bottles higher or lower much than the printer.

4. To be used in a dry place between 15 and 35degree. Avoid exposure to direct sunlight.

5. Don’t put the continuous ink supply systems reversed or leaning during the shipment.

Please make sure all the ink filling holes and Ventilation holes are closed tightly during the

transportation. Otherwise, the ink shall leak out.

6. Don’t sway the cartridge frequently. It may cause ink leakage.

7. Don’t pull out the connector of cartridge and don’t tear off adhesive tape at the bottom of

cartridge.

Warning:

1. Not drinkable; keep it out reach of children.

2. Avoid exposure to direct sunshine and don’t keep it in high or freezing temperature.

3. Avoid collision and fallen down.

Altri manuali per Stylus C63

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Epson Stampante

Epson

Epson WF-M5799 Manuale utente

Epson

Epson Mobilink TM-P60 Manuale per l'uso e la cura

Epson

Epson Stylus 1500 Manuale utente

Epson

Epson 1400 - Stylus Photo Color Inkjet Printer Manuale di istruzioni

Epson

Epson TM-U200 Series Manuale utente

Epson

Epson TM-S9000MJ Manuale utente

Epson

Epson TM-T70II-DT Manuale utente

Epson

Epson Stylus C66 Manuale utente

Epson

Epson WF-C5710 Series Manuale utente

Epson

Epson EPL-7000 Dimensioni

Epson

Epson WF-M5799 Manuale di istruzioni

Epson

Epson AcuLaser Color 2000 Manuale utente

Epson

Epson Stylus SX200 series Istruzioni per il montaggio

Epson

Epson LQ-50 Manuale utente

Epson

Epson Stylus SX230 Manuale utente

Epson

Epson WorkForce WF-7710 Manuale utente

Epson

Epson FX-880 - Impact Printer Manuale utente

Epson

Epson LQ-1150 II Manuale utente

Epson

Epson ET-4550 Manuale utente

Epson

Epson PictureMate PM-401 Manuale utente

Epson

Epson Stylus S21 Series Manuale utente

Epson

Epson TM-T81 Manuale utente

Epson

Epson R320 - Stylus Photo Color Inkjet Printer Manuale utente

Epson

Epson TM-T20II Manuale per l'uso e la cura

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente

IRA3D

IRA3D POETRY4 Manuale utente

Ricoh

Ricoh Aficio AP400 Manuale utente

BIXOLON

BIXOLON SRP-352plusV Manuale utente