Epson SureColor F7070 Manuale utente
Epson® SureColor®
F7070 Setup Guide
2|
Contents
Unpacking the Printer ...........................................................................................................................3
Assembling the Stand .............................................................................................................................6
Installing the Printer ............................................................................................................................10
Installing the Media Feeding Unit .......................................................................................................15
Installing the Take-up Reel System ......................................................................................................19
Setting the Language ............................................................................................................................22
Adjusting the Media System ................................................................................................................23
Loading Media ....................................................................................................................................25
Installing the Software .........................................................................................................................31
USB Installation ............................................................................................................................32
Network Installation .....................................................................................................................33
Unpacking the Printer |3
Read all of these instructions before using your printer. Also be sure to follow all warnings and instructions
marked on the printer and in the User’s Guide.
Unpacking the Printer
Before beginning assembly, make sure you have sufficient space to set up and use the printer. The
following illustration shows the minimum space required for using the printer:
Callout Distance
1 19.7 in. (500 mm)
2 3.9 in. (100 mm)
3 68.9 in. (1750 mm)
4 39.4 in. (1000 mm)
5 114.3 in. (2903 mm)
6 19.7 in. (500 mm)
7 39.4 in. (1000 mm)
8 142.5 in. (3620 mm)
4|Unpacking the Printer
When choosing a place for the printer, leave adequate room for easy access and ventilation. Avoid locations
subject to direct sunlight, excessive heat, humidity, or dust. Be sure the printer is placed on a flat, stable
location that can support 496 lb (225 kg).
Caution: Six people are required to unpack and install the printer.
You need an even larger floor space to assemble the printer and stand, so be sure to prepare a large, clear
area before unpacking them. Also make sure you save the box and packaging in case you need to ship the
printer later.
The following items should be included with your printer:
Printer and Stand Assembly
Printer
Carry bars
Horizontal struts
Power cord
Software and
documentation
Hex wrench
Legs
Waste ink
tank bracket
Waste
ink tank
Caution label
Cable
support Waste ink tube
bracket
Unpacking the Printer |5
Media System Assembly
The items below can be found in the “Ink Supply System Cover 1” box.
Media feeding unit
Take-up reel
Reel brackets
Adjustment paper
Roll core
Bracket and mounting
hardware
6|Assembling the Stand
Assembling the Stand
Make sure you have the following items before assembling the stand.
1. Slide the large horizontal strut into both of the legs.
2. Use the long end of the hex wrench to tighten the pre-placed screws on each of the legs.
back of stand
Assembling the Stand |7
3. Attach the smaller horizontal strut by securing two B screws (four total) in the back of the right and
left legs.
4. Attach the waste ink tank bracket and secure it with a B screw.
5. Attach one B screw to the other side of the bracket, move the slider into place, then attach another B
screw.
8|Assembling the Stand
6. Temporarily fasten the waste ink tube bracket using one B screw.
7. Remove the four screws, then remove the plastic piece.
8. Loosely fasten the mounting pieces to the bracket using three D screws and six washers.
Assembling the Stand |9
9. Slide the mounting pieces into the grooves, as shown.
10. Remove the screw, align the bracket, then fasten the screw to the stand.
11. Tighten the screws.
10 |Installing the Printer
12. Replace the plastic piece and then fasten it using the screws from step 7.
Installing the Printer
You need six people to install the printer; four people to carry it and two people to position it on the stand.
Use the carry bars to lift and move the printer.
Make sure you have the following items before installing the printer.
1. Lock the casters and fix the stand in place. To fix the stand, rotate the feet clockwise until they’re
firmly placed on the ground.
Altri manuali per SureColor F7070
3
Indice
Altri manuali Epson Stampante
Epson
Epson STYLUS C43UX Manuale
Epson
Epson Printer Guida all'installazione
Epson
Epson R340 - Stylus Photo Color Inkjet Printer Manuale utente
Epson
Epson PowerLite 460 Manuale utente
Epson
Epson Stylus CX3500 Series Manuale utente
Epson
Epson LQ-1150 Manuale di istruzioni
Epson
Epson DLQ-3000 Minerva+ Manuale utente
Epson
Epson SureColor P6000 Manuale utente
Epson
Epson F6070 Manuale utente
Epson
Epson ET-3700 Manuale di istruzioni
Epson
Epson WF-100 Manuale di istruzioni
Epson
Epson Stylus Pro 10000 Series Manuale utente
Epson
Epson SC-S80600 Series Manuale utente
Epson
Epson WorkForce AL-MX200DNF Istruzioni originali
Epson
Epson Stylus Photo R3000 Series Manuale utente
Epson
Epson 4012364-00 Manuale utente
Epson
Epson Stylus Pro GS6000 Manuale utente
Epson
Epson Stylus 1500 Manuale utente
Epson
Epson XP-452 Series Manuale utente
Epson
Epson WF-R5690 Manuale utente
