INTRODUCTION
This manual contains instructions for the assembly of an
Ericsson GE Desk Top Station. This is done by installing an
MDX mobile radio into the Desk Top Station Assembly, using
the hardware kit supplied.
Ericsson GE Mobile Radios which can be accommodated
by the Desk Top Station are MDX Conventional/EDACS Ra-
dios in the 800 and 900 MHz bands.
Included are mounting instructions for the radio, as well as
instructions for making the few required cable connections.
Installation is made easy with the help of an Installation Dia-
gram and an Interconnection Diagram, included as part of this
manual.
UNPACKING AND CHECKING
EQUIPMENT
Hardware Kit 349A9526 was used to assemble your sta-
tion. The unused material was shipped with the station. Re-
move the kit and store for possible use.
Copyright© September 1993, Ericsson GE Mobile Communications Inc.
Installation of the Ericsson GE Desk Top Station includes
three parts:
1. Installation of the Mobile Radio in the Desk Top Sta-
tion Assembly using Hardware Kit 349A9526 (sup-
plied).
2. Installation of Option Boards in the Desk Top Station
Assembly, in accordance with options selected. Re-
mote Interface Board Option, with one of the follow-
ing remote boards:
a. DC Remote Board
b. 4-Channel Tone Remote Board
c. 5-Channel EDACS Tone Remote Board
d. Standby Power Transfer Option
3. Installation of the Ericsson GE Desk Top Station in
the place of operation with the necessary power, an-
tenna, microphone, and line connections.
INSTALLATION
PREPARATION OF DESK TOP STATION
1. Loosen the two (2) captive screws which hold the
top cover on the Desk Top Assembly. Remove the
cover.
2. Disconnect cable W2 from J202 on the Intercon-
nect board.
3. Loosen, Do Not Remove, the two (2) M3.5 screws
that hold the radio mounting bracket on the Desk
Top Station Assembly.
4. When external wires for options are to be con-
nected, remove and discard the round knockout
button in the rear of the station housing. Insert the
rubber grommet 5490407P10 in the hole. Place the
cable clamp (344A3480P1) around the wires. Snap
the cable clamp retainer into the hole adjacent to
the grommet.
PREPARATION OF MOBILE RADIO
1. Remove the bottom cover of the radio by removing
the four (4) retaining TORX®
screws.
2. Unplug the radio internal speaker cable from J904
on the radio and let it hang.
3. Discard the rubber plug and in its place slip the
rubber sleeve on cable W2. P905 of W2 plugs into
J905.
4. Replace the bottom cover of the radio with the four
(4) retaining TORX®
screws removed in Step 1.
5. Using a permanent marker, copy the FCC identifi-
cation number of the radio onto the Desk Top Sta-
tion FCC label.
6. Attach the side mounting brackets with four (4) hex
mounting screws (2 per side) in the sides of the ra-
dio.
INSTALLING THE MOBILE RADIO
1. Connect P202 of cable W2 from the radio to J202
on the Interconnect Board.
2. Connect P101 of the Desk Top Station antenna ca-
ble W1 into J101 on the radio.
3. Connect P1 of the Desk Top Assembly power cable
W3 to J1 of the radio power cable W901.
4. Place the radio in the mounting bracket and posi-
tion it for the proper DeskTop Station front appear-
ance and tighten the two (2) M3.5 screws that hold
the radio mounting bracket in place.
5. Replace the Desk Top Assembly cover using the
two (2) screws loosened in Step 1 of "PREPARA-
TION OF DESK TOP STATION."
This completes the installation of the mobile radio in the
Desk Top Station Assembly.
INSTALLING THE DESK TOP STATION
AC Power
The Desk Top Station power supply must be connected
to AC power with the fused and ON/OFF-switched AC
power cable found at the back of the Desk Top Assembly.
The transformer straps are shipped set for a 120 volt power
source:
120volts ±10%, Single-Phase, 50/60 Hz, 4 amps,
500 watts
Refer to Power Supply Maintenance Manual LBI-38751
for procedures to change the transformer straps to accommo-
date a 240 volt power source:
240volts ±10%, Single-Phase, 50/60 Hz, 2 amps,
500 watts
Microphone
A desk microphone, a DTMF microphone, or a standard
mobile microphone can be used. The microphone connects
to the Desk Top Station at J101 on the Front Cap under the
Control Panel.
Antenna
A 50-ohm antenna is required. It should be connected
through coax cable to the Type N connector mounted in the
rear wall of the Desk Top Assembly.
TABLE OF CONTENTS
Page
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
UNPACKING AND CHECKING EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
PREPARATION OF DESK TOP STATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
PREPARATION OF MOBILE RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INSTALLING THE MOBILE RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INSTALLING THE DESK TOP STATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INSTALLING THE STANDBY POWER TRANSFER OPTION . . . . . . . . . . . . . . . . . . . . . . . . . 2
INSTALLING THE REMOTE OPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
ADJUSTING THE REMOTE OPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INSTALLING THE KEYPAD BOARD OPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
DIAGRAMS
INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
INTERCONNECTION DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
