ERNITEC MicroView MVIB-01IR-E Manuale utente

Network Bullet Camera

Quick Start Guide

MVIB-01IR-E

Network Bullet Camera·Quick Start Guide

About this Manual

This Manual is applicable to 20xx Network Camera.

The Manual includes instructions for using and managing the

product. Pictures, charts, images and all other information

hereinafter are for description and explanation only. The information

contained in the Manual is subject to change, without notice, due to

firmware updates or other reasons. Please find the latest version in

the company website

Please use this user manual under the guidance of professionals.

Legal Disclaimer

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF

PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. OUR COMPANY

SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION,

PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER

ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET

SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE TIMELY

TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL

RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS

PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE

APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE

EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE

APPLICABLE LAW, THE LATER PREVAILS.

Regulatory Information

FCC Information

Network Bullet Camera·Quick Start Guide

Please take attention that changes or modification not expressly

approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

FCC compliance: This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

Network Bullet Camera·Quick Start Guide

EU Conformity Statement

This product and - if applicable - the supplied

accessories too are marked with "CE" and comply

therefore with the applicable harmonized European

standards listed under the EMC Directive 2014/30/EU, the RoHS

Directive 2011/65/EU

2012/19/EU (WEEE directive): Products marked with

this symbol cannot be disposed of as unsorted

municipal waste in the European Union. For proper

recycling, return this product to your local supplier

upon the purchase of equivalent new equipment, or dispose of it at

designated collection points. For more information see:

www.recyclethis.info

2006/66/EC (battery directive): This product contains

a battery that cannot be disposed of as unsorted

municipal waste in the European Union. See the

product documentation for specific battery

information. The battery is marked with this symbol, which may

include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For proper recycling, return the battery to your supplier or to a

designated collection point. For more information see:

www.recyclethis.info

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (B)/NMB-3(B) standards

requirements.

Network Bullet Camera·Quick Start Guide

Safety Instruction

These instructions are intended to ensure that user can use the

product correctly to avoid danger or property loss.

The precaution measure is divided into “Warnings” and “Cautions”

Warnings: Serious injury or death may occur if any of the warnings

are neglected.

Cautions: Injury or equipment damage may occur if any of the

cautions are neglected.

Warnings

●In the use of the product, you must be in strict compliance with

the electrical safety regulations of the nation and region. Please

refer to technical specifications for detailed information.

●Input voltage should meet both the SELV (Safety Extra Low

Voltage) and the Limited Power Source with 24 VAC or 12 VDC

according to the IEC60950-1 standard. Please refer to technical

specifications for detailed information.

Warnings Follow these

safeguards to prevent

serious injury or death.

Cautions Follow these

precautions to prevent potential

injury or material damage.

Network Bullet Camera·Quick Start Guide

●Do not connect several devices to one power adapter as adapter

overload may cause over-heating or a fire hazard.

●Please make sure that the plug is firmly connected to the power

socket. When the product is mounted on wall or ceiling, the

device shall be firmly fixed.

●If smoke, odor or noise rise from the device, turn off the power

at once and unplug the power cable, and then please contact

the service center.

●Proper configuration of all passwords and other security settings

is the responsibility of the installer and/or end-u s e r.

Cautions

●Make sure the power supply voltage is correct before using the

camera.

●Do not drop the camera or subject it to physical shock.

●Do not touch sensor modules with fingers. If cleaning is

necessary, use clean cloth with a bit of ethanol and wipe it

gently. If the camera will not be used for an extended period,

please replace the lens cap to protect the sensor from dirt.

●Do not aim the camera at the sun or extra bright places.

Blooming or smearing may occur otherwise (which is not a

malfunction), and affect the endurance of sensor at the same

time.

●The sensor may be burned out by a laser beam, so when any

laser equipment is in using, make sure that the surface of sensor

will not be exposed to the laser beam.

Network Bullet Camera·Quick Start Guide

●Do not place the camera in extremely hot, cold (the operating

temperature shall be-30°C ~+60°C, or -40°C ~ +60°C if the

camera model has an “H” in its suffix), dusty or damp locations,

and do not expose it to high electromagnetic radiation.

●To avoid heat accumulation, good ventilation is required for

operating environment.

●Keep the camera away from liquid while in use.

●While in delivery, the camera shall be packed in its original

packing, or packing of the same texture.

●Regular part replacement: a few parts (e.g. electrolytic

capacitor) of the equipment shall be replaced regularly

according to their average enduring time. The average time

varies because of differences between operating environment

and using history, so regular checking is recommended for all the

users. Please contact with your dealer for more details.

●Improper use or replacement of the battery may result in hazard

of explosion. Replace with the same or equivalent type only.

Dispose of used batteries according to the instructions provided

by the battery manufacturer.

●If the product does not work properly, please contact your

dealer or the nearest service center. Never attempt to

disassemble the camera yourself. (We shall not assume any

responsibility for problems caused by unauthorized repair or

maintenance.)

Network Bullet Camera·Quick Start Guide

Table of Contents

1 Appearance Description ................................................................. 9

Overview of Type I Bullet Camera ................................... 9

Overview of Type II Bullet Camera ................................ 11

Resetting the Camera ......................................... 12

Setting the WPS Protocol.................................... 13

Overview of Type III Bullet Camera ............................... 15

2 Installation.................................................................................... 17

Installation of Memory Card ......................................... 18

Installation of the Bullet Camera ................................... 19

Installation of Network Cable Water-proof Jacket

(Optional) ................................................................................. 21

3 Setting the Network Camera over the LAN .................................. 24

Wiring ........................................................................... 24

Activating the Camera................................................... 25

Activation via Web Browser................................ 25

Activation via SADP Software ............................. 26

Modifying the IP Address .............................................. 28

4 Accessing via Web Browser .......................................................... 31

5 Operating via Guarding Vision App .............................................. 33

Enable Guarding Vision Service on Camera ................... 33

Enable Guarding Vision Service via SADP Software

......................................................................................... 33

Enable Guarding Vision Service via Web Browser34

Guarding Vision Setup ................................................... 36

Adding Camera to Guarding Vision................................ 36

Initializing the Memory Card ......................................... 38

Network Bullet Camera·Quick Start Guide

0504051070109

Network Bullet Camera·Quick Start Guide

1Appearance Description

Overview of Type I Bullet Camera

Type I Bullet Camera

Altri manuali per MicroView MVIB-01IR-E

Indice

Altri manuali ERNITEC Telecamera di sicurezza

ERNITEC

ERNITEC MicroView MVID-03IR-E Manuale utente

ERNITEC

ERNITEC ECB Series Manuale utente

ERNITEC

ERNITEC Orion/3-DN Outdoor Istruzioni di montaggio

ERNITEC

ERNITEC MicroView MVIB-04IR-E Manuale utente

ERNITEC

ERNITEC MicroView MVIC-O4IR-E Manuale utente

ERNITEC

ERNITEC MERCURY SX 5TH GENERATION Manuale utente

ERNITEC

ERNITEC ASTRAL Istruzioni per il montaggio

ERNITEC

ERNITEC SX Manuale utente

ERNITEC

ERNITEC DS-2CD6924G0-IHS Manuale utente

ERNITEC

ERNITEC MicroView MVCLOUD-201 Manuale utente

ERNITEC

ERNITEC MVID-04IR-E Manuale utente

ERNITEC

ERNITEC Orion/2 Manuale utente

ERNITEC

ERNITEC Hawk SX Manuale utente

ERNITEC

ERNITEC MicroView MVCLOUD-101 Manuale utente

ERNITEC

ERNITEC Mercury SX32 Series Manuale utente

ERNITEC

ERNITEC MicroView MVIC-04IR-E Manuale utente

ERNITEC

ERNITEC Orion DX 832 IR Manuale utente

ERNITEC

ERNITEC Orion SX Series Manuale utente

ERNITEC

ERNITEC Mercury SX4 series Manuale utente

ERNITEC

ERNITEC MicroView MVIB-01IR-E Manuale utente

ERNITEC

ERNITEC MicroView MVCLOUD-201 Manuale utente

ERNITEC

ERNITEC Orion/2 Guida

ERNITEC

ERNITEC Corona IP-452 IR Manuale utente

ERNITEC

ERNITEC Orion/2 Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente