ERNITEC Performance Series Manuale utente

Bullet Network Camera

Quick Start Guide

Any and all information, including, among others, wordings, pictures,

graphs are the properties of Hangzhou Hikvision Digital Technology

Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).

This user manual (hereinafter referred to be “the Manual”) cannot

be reproduced, changed, translated, or distributed, partially or whol-

ly, by any means, without the prior written permission of Hikvision.

Unless otherwise stipulated, Hikvision does not make any warran-

ties, guarantees or representations, express or implied, regarding to

the Manual.

About this Manual

This Manual is applicable to Bullet Network Camera.

The Manual includes instructions for using and managing the prod-

uct. Pictures, charts, images and all other information hereinafter

are for description and explanation only. The information contained

in the Manual is subject to change, without notice, due to rmware

updates or other reasons. Please nd the latest version in the com-

pany website (http://overseas.hikvision.com/en/).

Please use this user manual under the guidance of professionals.

Trademarks Acknowledgement

and other Hikvision’s trademarks and logos are

the properties of Hikvision in various jurisdictions. Other trademarks

and logos mentioned below are the properties of their respective

owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE

LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE,

SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL

FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRAN-

TIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITA-

TION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS

FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF

THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS,

OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR

ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT

DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR

LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR

LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH

THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE

USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.

HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR AB-

NORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAM-

AGES RESULTING FROM CYBER ATTACK, HACKER ATTACK,

VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;

HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL

SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE

CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE

USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR

USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL

NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED

WITH ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL

AND THE APPLICABLE LAW, THE LATER PREVAILS.

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly ap-

proved by the party responsible for compliance could void the user’s

authority to operate the equipment.

FCC compliance: This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help

FCC conditions

This device complies with part 15 of the FCC Rules. Operation is sub-

ject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interfer-

ence that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories

too are marked with "CE" and comply therefore withthe

applicable harmonized European standards listed under

the the EMC Directive 2014/30/EU, the RoHS Directive

2011/65/EU.

2012/19/EU (WEEE directive): Products marked with

this symbol cannot be disposed of as unsorted municipal

waste in the European Union. For proper recycling, return

this product to your local supplier upon the purchase of

equivalent new equipment, or dispose of it at designated

collection points. For more information see: www.

recyclethis.info

2006/66/EC and its amendment 2013/56/EU (battery

directive): This product contains a battery that cannot be

disposed of as unsorted municipal waste in the European

Union. See the product documentation for specic battery

information. The battery is marked with this symbol, which

may include lettering to indicate cadmium (Cd), lead (Pb),

or mercury (Hg). For proper recycling, return the battery to

your supplier or to a designated collection point. For more

information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (B)/NMB-3(B) standards require-

ments.

Safety Instruction

These instructions are intended to ensure that the user can

use the product correctly to avoid danger or property loss.

Laws and Regulations

The device should be used in compliance with local laws,

electrical safety regulations, and re prevention regulations.

Transportation

Keep the device in original or similar packaging while

transporting it.

Power Supply

The input voltage should conform to IEC60950-1 standard:

SELV (Safety Extra Low Voltage) and the Limited Power

Source. Refer to the appropriate documentation for detailed

information.

DO NOT connect multiple devices to one power adapter, to

avoid over-heating or re hazards caused by overload.

Make sure the plug is properly connected to the power

socket.

System Security

The installer and user are responsible for password and

security conguration and its settings.

Battery

Improper use or replacement of the battery may result in

explosion hazard. Replace with the same or equivalent

type only. Dispose of used batteries in conformance with

the local codes.

Maintenance

If the product does not work properly, please contact your

dealer or the nearest service center. We shall not assume

any responsibility for problems caused by unauthorized

repair or maintenance.

A few device components (e.g., electrolytic capacitor)

require regular replacement. The average lifespan varies,

so periodic checking is recommended. Contact your dealer

for details.

Cleaning

Please use a soft and dry cloth when clean inside and

outside surfaces of the product cover. Do not use alkaline

detergents.

Using Environment

When any laser equipment is in use, make sure that the

device lens is not exposed to the laser beam, or it may burn

out.

Do not expose the device to high electromagnetic radiation

or dusty environments.

For indoor-only device, place it in a dry and well-ventilated

environment.

Do not aim the lens at the sun or any other bright light.

Make sure the running environment meets the requirement

of the device. The operating temperature shall be -30 °C to

60 °C (-22 °F to 140 °F), and the operating humidity shall

be 95% or less (no condensing).

Do not place the camera in extremely hot, cold,

dusty or damp locations, and do not expose it to high

electromagnetic radiation.

Emergency

If smoke, odor, or noise arises from the device, immediately

turn off the power, unplug the power cable, and contact the

service center.

Time Synchronization

Set up camera time manually for the rst time access if the

local time is not synchronized with that of the network. Visit

the camera via Web browse/client software and go to time

settings interface.

Installation

Make sure the device is rmly secured to any wall or ceiling

mountings.

Be sure that there is enough space to install the camera

and accessories.

Make sure that the device in the package is in good

condition and all the assembly parts are included.

Make sure that the wall is strong enough to withstand at

least 4 times the weight of the camera and the mount.

The standard power supply is 12 VDC, please make sure

your power supply matches with your camera.

Make sure that the power has been disconnected before

you wire, install, or disassemble the device.

Make sure that no reective surface is too close to the

camera lens. The IR light from the camera may reect back

into the lens causing reection.

For device with this sticker, this device is

intended for installation in a restricted access

location, access can only be gained by service

persons or by users who have been instructed about the

reasons for the restrictions applied to the location and

about any precautions that shall be taken.

Symbols and Marks

Notice

Warning

Forbidden

Correct

Incorrect

Turn to page A and continue.

i. Not necessarily included accessory.

ii. Variable accessory amount.

iii. Skip this step if not required.

MicroSD card

Grounding

Disposal

Purchase separately

Other situations

Other situations omitted

Waterproof

Skip this step if not necessary

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ERNITEC Telecamera di sicurezza

ERNITEC

ERNITEC MicroView MVIB-04IR-E Manuale utente

ERNITEC

ERNITEC DS-2XM6726G0-IS/ND Manuale utente

ERNITEC

ERNITEC Orion Manuale utente

ERNITEC

ERNITEC Orion/2 Manuale utente

ERNITEC

ERNITEC EVA 101 Manuale utente

ERNITEC

ERNITEC ASTRAL Istruzioni per il montaggio

ERNITEC

ERNITEC MicroView MVIC-O4IR-E Manuale utente

ERNITEC

ERNITEC MicroView MVIC-04IR-E Manuale utente

ERNITEC

ERNITEC Corona IP-452 IR Manuale utente

ERNITEC

ERNITEC MicroView MVCLOUD-201 Manuale utente

ERNITEC

ERNITEC Mercury SX32 Series Manuale utente

ERNITEC

ERNITEC MicroView MVCLOUD-101 Manuale utente

ERNITEC

ERNITEC SX Series Manuale utente

ERNITEC

ERNITEC MicroView MVCLOUD-201 Manuale utente

ERNITEC

ERNITEC SX Manuale utente

ERNITEC

ERNITEC Hawk SX Manuale utente

ERNITEC

ERNITEC MVID-04IR-E Manuale utente

ERNITEC

ERNITEC Orion/3-DN Outdoor Istruzioni di montaggio

ERNITEC

ERNITEC EIP Series Manuale utente

ERNITEC

ERNITEC Mercury SX4 series Manuale utente

ERNITEC

ERNITEC Orion/2 Guida

ERNITEC

ERNITEC DS-2CD6924G0-IHS Manuale utente

ERNITEC

ERNITEC Orion/2 Manuale utente

ERNITEC

ERNITEC ECB Series Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente