ERNITEC MicroView MVIB-04IR-E Manuale utente
Bullet Network Camera
MVIB-04IR-E
Quick Start Guide
Quick Start Guide
About this Manual
This Manual is applicable to MVIB-04IR-E Bullet Network Camera.
The Manual includes instructions for using and managing the product.
Pictures, charts, images and all other information hereinafter are for
description and explanation only. The information contained in the
Please use this user manual under the guidance of professionals.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW,
THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE
AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS
AND ERRORS, AND OUR COMPANY MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A
PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD
PARTY. IN NO EVENT WILL OUR COMPANY, ITS DIRECTORS,
OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR
ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS
OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF
THIS PRODUCT, EVEN IF OUR COMPANY HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE
USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITES
FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER
DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK,
VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL
SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK
ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING
THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE
CONFORMS THE APPLICABLE LAW. OUR COMPANY SHALL NOT
BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH
ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND
THE APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information
FCC Information
Please take attention that changes or modication not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
FCC compliance: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to ra-
dio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help
FCC conditions
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interfer-
ence that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories
too are marked with "CE" and comply therefore withthe
applicable harmonized European standards listed under the
the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/
EU.
2012/19/EU (WEEE directive): Products marked with this
symbol cannot be disposed of as unsorted municipal waste in
the European Union. For proper recycling, return this product
to your local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection points.
For more information see: www.recyclethis.info
2006/66/EC and its amendment 2013/56/EU (battery
directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which
may include lettering to indicate cadmium (Cd), lead (Pb),
or mercury (Hg). For proper recycling, return the battery to
your supplier or to a designated collection point. For more
information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards require-
ments.
Safety Instruction
These instructions are intended to ensure that the user can use the
product correctly to avoid danger or property loss.
Laws and Regulations
The device should be used in compliance with local laws, electrical
safety regulations, and re prevention regulations.
Transportation
Keep the device in original or similar packaging while transporting it.
Power Supply
The input voltage should conform to IEC60950-1 standard: SELV
(Safety Extra Low Voltage) and the Limited Power Source. Refer to
the appropriate documentation for detailed information.
DO NOT connect multiple devices to one power adapter, to avoid
over-heating or re hazards caused by overload.
Make sure the plug is properly connected to the power socket.
System Security
The installer and user are responsible for password and security
conguration and its settings.
Battery
Improper use or replacement of the battery may result in explosion
hazard. Replace with the same or equivalent type only. Dispose of
used batteries in conformance with the local codes.
Maintenance
If the product does not work properly, please contact your dealer or
the nearest service center. We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.
A few device components (e.g., electrolytic capacitor) require regular
replacement. The average lifespan varies, so periodic checking is
recommended. Contact your dealer for details.
Cleaning
Please use a soft and dry cloth when clean inside and outside
surfaces of the product cover. Do not use alkaline detergents.
Using Environment
When any laser equipment is in use, make sure that the device lens is
not exposed to the laser beam, or it may burn out.
Do not expose the device to high electromagnetic radiation or dusty
environments.
For indoor-only device, place it in a dry and well-ventilated
environment.
Do not aim the lens at the sun or any other bright light.
Make sure the running environment meets the requirement of the
device. The operating temperature shall be -30 °C to 60 °C (-22
°F to 140 °F), and the operating humidity shall be 90% or less (no
condensing).
Do not place the camera in extremely hot, cold, dusty or damp
locations, and do not expose it to high electromagnetic radiation.
Emergency
If smoke, odor, or noise arises from the device, immediately turn off
the power, unplug the power cable, and contact the service center.
Time Synchronization
Set up camera time manually for the rst time access if the local time
is not synchronized with that of the network. Visit the camera via Web
browse/client software and go to time settings interface.
Installation
Make sure the device is firmly secured to any wall or ceiling
mountings.
Be sure that there is enough space to install the camera and
accessories.
Make sure that the device in the package is in good condition and all
the assembly parts are included.
Make sure that the wall is strong enough to withstand at least 4 times
the weight of the camera and the mount.
The standard power supply is 12 VDC, or PoE (802.3at), please make
sure your power supply matches with your camera.
Make sure that the power has been disconnected before you wire,
install, or disassemble the device.
Make sure that no reective surface is too close to the camera lens.
The IR light from the camera may reect back into the lens causing
reection.
Symbols and Marks
Notice
Warning
Forbidden
Correct
Incorrect
Turn to page A and continue.
i. Not necessarily included accessory.
ii. Variable accessory amount.
iii. Skip this step if not required.
MicroSD card
Grounding
Disposal
Purchase separately
1x 1x
1x 1x1x
1x
1x
1x
T10
T20
2x*
1
1.1
microSD
*
32
1.2
32
Indice
Altri manuali ERNITEC Telecamera di sicurezza
ERNITEC
ERNITEC Orion/3-DN Outdoor Istruzioni di montaggio
ERNITEC
ERNITEC MicroView MVIB-01IR-E Manuale utente
ERNITEC
ERNITEC Orion/2 Guida
ERNITEC
ERNITEC EVA 101 Manuale utente
ERNITEC
ERNITEC MicroView MVID-03IR-E Manuale utente
ERNITEC
ERNITEC MVID-04IR-E Manuale utente
ERNITEC
ERNITEC EIP Series Manuale utente
ERNITEC
ERNITEC Orion/2 Manuale utente
ERNITEC
ERNITEC ASTRAL Istruzioni per il montaggio
ERNITEC
ERNITEC DS-2CD6924G0-IHS Manuale utente
ERNITEC
ERNITEC Orion SX Series Manuale utente
ERNITEC
ERNITEC DS-2XM6726G0-IS/ND Manuale utente
ERNITEC
ERNITEC MicroView MVCLOUD-101 Manuale utente
ERNITEC
ERNITEC SX Manuale utente
ERNITEC
ERNITEC Mercury SX32 Series Manuale utente
ERNITEC
ERNITEC Orion DX 3 Manuale utente
ERNITEC
ERNITEC MERCURY SX 5TH GENERATION Manuale utente
ERNITEC
ERNITEC Orion/2 Manuale utente
ERNITEC
ERNITEC DS-2CD6986F-H Manuale utente
ERNITEC
ERNITEC MicroView MVCLOUD-201 Manuale utente
