ESAB Aristo RoboFeed 3004w Manuale utente

ÎÎÎÎÎÎÎÎÎÎÎÎÎ

Valid for serial no. 745-xxx-xxxx0461 165 001 GB 20120808

Aristo®

RoboFeed 3004w

Instruction manual

- 2 -

- 3 -

TOCe

Rights reserved to alter specifications without notice.

1 SAFETY 4...........................................................

2 INTRODUCTION 6...................................................

2.1 Equipment 6................................................................

3 TECHNICAL DATA 6.................................................

4 INSTALLATION 7....................................................

4.1 Terminating resistor 7........................................................

4.2 Example of a robotic welding system 7.........................................

5 OPERATION 8.......................................................

5.1 Connection and control devices 9.............................................

5.2 Water connection 10..........................................................

5.3 Gas flow guard (if installed) 10.................................................

5.4 Wire feed pressure 11........................................................

5.5 Replacing and inserting wire 11................................................

5.6 Changing feed rollers 11......................................................

6 MAINTENANCE 12....................................................

6.1 Inspection and cleaning 12....................................................

7 ORDERING OF SPARE PARTS 12......................................

DIAGRAM 14............................................................

ORDER NUMBER 16.....................................................

WEAR PARTS 18........................................................

ACCESSORIES 20.......................................................

- 4 -

bm51d1ea

1 SAFETY

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or

near the equipment observes all the relevant safety precautions. Safety precautions must meet the

requirements that apply to this type of equipment. The following recommendations should be ob

served in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the equip

ment. Incorrect operation of the equipment may lead to hazardous situations which can result in in

jury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

Sits operation

Slocation of emergency stops

Sits function

Srelevant safety precautions

Swelding and cutting

2. The operator must ensure that:

Sno unauthorised person is stationed within the working area of the equipment when it is

started up.

Sno-one is unprotected when the arc is struck

3. The workplace must:

Sbe suitable for the purpose

Sbe free from drafts

4. Personal safety equipment

SAlways wear recommended personal safety equipment, such as safety glasses, flame-proof

clothing, safety gloves.

SDo not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

SMake sure the return cable is connected securely.

SWork on high voltage equipment may only be carried out by a qualified electrician.

SAppropriate fire extinquishing equipment must be clearly marked and close at hand.

SLubrication and maintenance must not be carried out on the equipment during operation.

- 5 -

bm51d1ea

WARNING

Read and understand the instruction manual before installing or operating.

Arc welding and cutting can be injurious to yourself and others. Take precautions when welding and

cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard

data.

ELECTRIC SHOCK - Can kill

SInstall and earth the unit in accordance with applicable standards.

SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

SInsulate yourself from earth and the workpiece.

SEnsure your working stance is safe.

FUMES AND GASES - Can be dangerous to health

SKeep your head out of the fumes.

SUse ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS - Can injure eyes and burn skin.

SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

SProtect bystanders with suitable screens or curtains.

FIRE HAZARD

SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE - Excessive noise can damage hearing

SProtect your ears. Use earmuffs or other hearing protection.

SWarn bystanders of the risk.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION

Class A equipment is not intended for use in residential locations where

the electrical power is provided by the public low-voltage supply system.

There may be potential difficulties in ensuring electromagnetic

compatibility of class A equipment in those locations, due to conducted

as well as radiated disturbances.

CAUTION

Read and understand the instruction manual before

installing or operating.

Dispose of electronic equipment at the recycling facility!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment and its implementation in accordance with national law, electrical and/or

electronic equipment that has reached the end of its life must be disposed of at a

recycling facility.

As the person responsible for the equipment, it is your responsibility to obtain

information on approved collection stations.

For further information contact the nearest ESAB dealer.

- 6 -

bm51d1ea

CAUTION

This product is solely intended for arc welding.

ESAB can provide you with all necessary welding protection and accessories.

2 INTRODUCTION

The RoboFeed 3004w wire feed unit is intended for MIG/MAG welding along with

robotic equipment.

2.1 Equipment

The wire feed unit is supplied with an instruction manual and a sticker with

recommended wear parts.

3 TECHNICAL DATA

RoboFeed 3004w

Power supply 42 V 50-60 Hz

Power requirement 147 VA

Motor current Imax 8 A

Wire feed speed 0.8-30.0 m/min

Gun connection EURO

Wire dimension

Cored wire

0.6-1.6 mm

0.6-1.2 mm

1.0-1.6 mm

0.8-1.6 mm

Weight 7.3 kg

Dimensions (l x b x h) 362 x 246 x 235 mm

Shielding gas

max pressure

Gases for MIG/MAG welding

5 bar

Coolant

max pressure

50% water / 50% mono-ethylene glycol

5 bar

Maximum permissible load at

60% duty cycle

100% duty cycle

500 A

280 A

Enclosure class IP2X

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at

a certain load without overloading. The duty cycle is valid for 40°C.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Apparatus marked IP2X are intended for indoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

- 7 -

bm51d1ea

4 INSTALLATION

The installation must be carried out by a professional.

WARNING

When welding in an environment with increased electrical danger, only power

sources intended for this environment may be used. These power sources are

marked with the symbol

4.1 Terminating resistor

The ends of the CAN bus must be fitted with terminating

resistors to avoid communication interference.

The terminating resistor is delivered with the power source.

One end of the CAN bus is at the control panel, which

has an integral terminating resistor. The other end is at

the wire feed unit and must be fitted with the

terminating resistor, as shown on the right.

4.2 Example of a robotic welding system

- 8 -

bm51d1ea

5 OPERATION

General safety regulations for handling the equipment can be found on

page 4. Read through before you start using the equipment!

WARNING

Assure that the side panels are closed during operation.

WARNING

Rotating parts can cause injury, take great care.

H 0935

- 9 -

bm51d1ea

5.1 Connection and control devices

1White indicating lamp – Power supply ON 9Connection for coolant from power source

(cooling unit), BLUE

2Switch for gas purging 10 Inlet connection for spatter removal air

3Switch for reversed wire feed 11 Connection for coolant to power source

(cooling unit), RED

4Switch for cold wire feed 12 Quick connector MarathonPact

5Connection for signals to/from robot

welding gun

13 Connection for shielding gas

6ELP* - Connection for coolant to welding

gun BLUE and from welding gun RED

14 Connection for welding current from power

source, (OKC)

7Outlet connection for spatter removal air 15 Connection for terminating resistor or

forwarding to next wire feed unit

8 Connection for welding gun (EURO) 16 Connection for control cable from power

source

* ELP = ESAB Logic Pump, see 5.2

ÄÄÄÄÄÄÄ

- 10 -

bm51d1ea

Symbol and function explanations

Inlet spatter removal air (10)

Shielding gas (13)

Outlet spatter removal air (6)

Used for spray-cleaning the contact tip on the welding gun.

Gas purging (2)

Used to measure the gas flow or to flush the gas hoses to clean them of any air and

moisture before commencing welding. Gas purging is carried out with the voltage

and wire feed switched off.

Reversed wire feed (3)

Used to reverse the wire, for example when replacing the wire bobbin.

Inching (4)

Used when wire is to be fed without switching on the welding voltage.

5.2 Water connection

The wire feed unit with water connection is equipped with a detection system ELP

(ESAB Logic Pump) which checks that the water hoses are connected. When

connecting a water-cooled welding gun, the water pump starts.

Detection only works with power sources that are equipped with ELP.

5.3 Gas flow guard (if installed)

The gas flow monitor interrupts the ongoing welding process if the gas flow drops

below 3.5 l/min. When this occurs, an error message is displayed via the control unit.

Altri manuali per Aristo RoboFeed 3004w

Indice

Altri manuali ESAB Sistema di saldatura

ESAB

ESAB EPP-200 Manuale utente

ESAB

ESAB POWERCUT-1500 Manuale utente

ESAB

ESAB EMP 320ic Manuale utente

ESAB

ESAB Powercut 900 Manuale utente

ESAB

ESAB CaddyArc 150 Manuale utente

ESAB

ESAB CoolMidi 1800 Manuale utente

ESAB

ESAB ES 180i Manuale utente

ESAB

ESAB LPH 80 Manuale utente

ESAB

ESAB PCM-875 Manuale utente

ESAB

ESAB LKA 180 Manuale utente

ESAB

ESAB Thermal Dynamics CUTMASTER 40 Manuale utente

ESAB

ESAB POWERCUT-1250 Manuale utente

ESAB

ESAB Aristotig 255 AC/DC Manuale utente

ESAB

ESAB DTG 405 Manuale utente

ESAB

ESAB Renegade ET 180iP Manuale utente

ESAB

ESAB Origo M13y YardFeed 200 Manuale utente

ESAB

ESAB Smashweld 316 Manuale utente

ESAB

ESAB Rogue ES 130i PRO Manuale utente

ESAB

ESAB OXWELD C-62 Manuale utente

ESAB

ESAB A2 SF Manuale utente

ESAB

ESAB MIGMASTER 250 Manuale utente

ESAB

ESAB TIG 400i Manuale utente

ESAB

ESAB Cutmaster 60 Manuale utente

ESAB

ESAB Aristo Mig U4000i Manuale utente

Manuali Sistema di saldatura popolari di altre marche

Berner

Berner PLASMACUT 54 Manuale utente

Pro Spot

Pro Spot PR-155 Manuale utente

Forney

Forney 210 Manuale utente

Thermal Arc

Thermal Arc 400S Manuale utente

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuale utente

GYS

GYS PROTIG 201 AC/DC Manuale utente

TAFA

TAFA 30*8B35 Manuale utente

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuale utente

CIGWELD

CIGWELD 636804 Guida rapida

Red-D-Arc

Red-D-Arc DC-400 Manuale utente

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuale utente

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuale utente

WIA

WIA Weldmatic 270 CP132-2 Manuale utente

Sonics

Sonics H520T Manuale utente

Miller

Miller Big Blue 400D Manuale utente

NewArc

NewArc RT2000 Guida rapida

Hypertherm

Hypertherm powermax1000 Manuale utente

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuale utente