ESAB PowerCut 700 PT-39 Manuale utente

Valid for serial no. 145-xxx-xxxx0463 339 001 GB 20121125

PowerCut™ 700

PT-39

Instruction manual

- 2 -

- 3 -

- 4 -

- 5 -

TOCe

Rights reserved to alter specifications without notice.

APPLICATIONS 24.......................................................

1 SAFETY 6...........................................................

2 INTRODUCTION 8...................................................

2.1 Equipment 8................................................................

3 TECHNICAL DATA 8.................................................

4 INSTALLATION 9....................................................

4.1 Delivery check and location 10.................................................

4.2 Primary power supply 11......................................................

4.3 Input air connection 12........................................................

4.4 Connection for return cable 12.................................................

4.5 Connection of torch 13........................................................

4.5.1 Disconnecting the Torch 14...............................................

4.5.2 Connecting the Torch 14..................................................

5 OPERATION 15.......................................................

5.1 Connections 15..............................................................

5.2 Control devices 16...........................................................

5.2.1 Symbol key 17..........................................................

5.3 Installing consumables for the torch 18..........................................

5.4 Cutting 19...................................................................

6 MAINTENANCE 20....................................................

6.1 Inspection and cleaning 21....................................................

7 TROUBLESHOOTING 21..............................................

7.1 Troubleshooting guide 22......................................................

8 ORDERING SPARE PARTS 23.........................................

DIAGRAM 24............................................................

WEAR PARTS 27........................................................

ORDER NUMBER 28.....................................................

- 6 -

bp29e

1 SAFETY

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or

near the equipment observes all the relevant safety precautions. Safety precautions must meet the

requirements that apply to this type of equipment. The following recommendations should be

observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the

equipment. Incorrect operation of the equipment may lead to hazardous situations which can result

in injury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

Sits operation

Slocation of emergency stops

Sits function

Srelevant safety precautions

Swelding and cutting

2. The operator must ensure that:

Sno unauthorised person is stationed within the working area of the equipment when it is

started up.

Sno-one is unprotected when the arc is struck

3. The workplace must:

Sbe suitable for the purpose

Sbe free from drafts

4. Personal safety equipment

SAlways wear recommended personal safety equipment, such as safety glasses, flame-proof

clothing, safety gloves.

SDo not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

SMake sure the return cable is connected securely.

SWork on high voltage equipment may only be carried out by a qualified electrician.

SAppropriate fire extinquishing equipment must be clearly marked and close at hand.

SLubrication and maintenance must not be carried out on the equipment during operation.

- 7 -

bp29e

WARNING

Read and understand the instruction manual before installing or operating.

Arc welding and cutting can be injurious to yourself and others. Take precautions when welding and

cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard

data.

ELECTRIC SHOCK - Can kill

SInstall and earth the unit in accordance with applicable standards.

SDo not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.

SInsulate yourself from earth and the workpiece.

SEnsure your working stance is safe.

FUMES AND GASES - Can be dangerous to health

SKeep your head out of the fumes.

SUse ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS - Can injure eyes and burn skin.

SProtect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

SProtect bystanders with suitable screens or curtains.

FIRE HAZARD

SSparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE - Excessive noise can damage hearing

SProtect your ears. Use earmuffs or other hearing protection.

SWarn bystanders of the risk.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

WARNING

Do not use the power source for thawing frozen pipes.

CAUTION

Class A equipment is not intended for use in residential locations where

the electrical power is provided by the public low-voltage supply system.

There may be potential difficulties in ensuring electromagnetic

compatibility of class A equipment in those locations, due to conducted

as well as radiated disturbances.

CAUTION

This product is solely intended for plasma cutting.

CAUTION

Read and understand the instruction manual before

installing or operating.

- 8 -

bp29e

Dispose of electronic equipment at the recycling facility!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment and its implementation in accordance with national law, electrical and/or

electronic equipment that has reached the end of its life must be disposed of at a

recycling facility.

As the person responsible for the equipment, it is your responsibility to obtain

information on approved collection stations.

For further information contact the nearest ESAB dealer.

ESAB can provide you with all necessary cutting protection and accessories.

2 INTRODUCTION

The PowerCut 700 is a complete system for manual plasma cutting. It delivers

cutting power for severing materials up to 20 mm thickness.

2.1 Equipment

The power source is supplied with:

Spower cable, 3 m

Sinstruction manual

Sreturn cable with clamp

Splasma cutting torch PT-39, 7.5 m, supplied as indicated on page 28

Swear part kit for PT-39.

3 TECHNICAL DATA

PowerCut 700

Mains voltage 400 V $10 %, 3-ph, 50/60 Hz

Setting range 30 – 50 A

Permitted load

30 % duty cycle

60 % duty cycle

100% duty cycle

50 A

37 A

30 A

Power factor at max current 0.75

Efficiency at maximum current 85 %

Open-circuit voltage U0320 V

Operating temperature -10 to 40 °C

Transportation temperature -20 to 55 °C

Sound pressure at no load < 70 db (A)

Nominal flow rate 189 l/min at 4.8 bar

Dimensions, l x w x h 600 x 210 x 380 mm

Weight incl torch and return cable 25.5 kg

Insulation class transformer H

Enclosure class IP 23

Application class

- 9 -

bp29e

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at

a certain load without overloading. The duty cycle is valid for 40°C.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid

objects or water. Equipment marked IP23 is designed for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

4 INSTALLATION

The installation must be carried out by a professional.

Correct installation is very important for trouble-free operation and good cutting

results. Carefully read and follow each step in this chapter.

WARNING

ELECTRIC SHOCKS CAN KILL Take precautionary measures against electric

shocks. Ensure that all power supplies are disconnected –switch off the switch

at the wall socket and pull out the equipment's power cable from the socket before

making any electrical connections in the power source.

WARNING

It is very important that the chassis is connected to the approved electric protective

earth, to prevent electric shocks and electrical accidents. Ensure that protective

earth is not connected to any phase conductors by mistake.

WARNING

Poor connections or failure to connect the return cable to the workpiece can result

in fatal electric shock.

WARNING

Air filter devices may not be used –installation or mounting of any form of air

filter device obstructs the cold air flow and causes a risk of overheating.

The warranty is invalidated if any type of air filter is used.

- 10 -

bp29e

WARNING

Do NOT start the equipment with the cover removed.

Do NOT connect the power source with the main switch in ON position

or when you are holding it or carrying it.

Do NOT touch any of the torch's parts when the power supply is on.

CAUTION

This product is intended for industrial use. In a domestic environment this product may

cause radio interference. It is the user's responsibility to take adequate precautions.

CAUTION

Place the power source at least 3 metres from the cutting area as sparks and slag spray

can damage the power source

4.1 Delivery check and location

1. Remove the packaging. Inspect the equipment for damage that was not

immediately apparent upon reception of the delivery. Immediately report any

damage to the delivery company.

2. Check for any loose parts in the packaging. Check that the air ducts in the

cover's rear panel are not blocked by packaging material that can prevent the air

flow through the power source.

The power source has a carrying handle and can be lifted easily.

3. Position the power source so that its cooling air inlets and outlets are not

obstructed. Minimum permitted distance to wall or other obstruction is 1 m.

4. An air source that gives clean and dry air, at least 189 l/m at 4.8 bar, is

required for cutting. The cutting air pressure must not exceed 6 bar, which is the

maximum inlet pressure for the filter regulator that is included in the delivery.

Altri manuali per PowerCut 700 PT-39

Indice

Altri manuali ESAB Sistema di saldatura

ESAB

ESAB Caddy Arc 251i Manuale utente

ESAB

ESAB LPH 120 Manuale utente

ESAB

ESAB PKB 250 Manuale utente

ESAB

ESAB Origo M13 Feed 304 Manuale utente

ESAB

ESAB Aristo Mig 5000i 400 V Manuale utente

ESAB

ESAB PowerCut-550 Manuale utente

ESAB

ESAB EM235ic Manuale utente

ESAB

ESAB AristoPower 4600c Manuale utente

ESAB

ESAB Mig C420 Manuale utente

ESAB

ESAB TAF 1251 Manuale utente

ESAB

ESAB Origo Mig L305 Manuale utente

ESAB

ESAB OrigoFeed 30-4 Manuale utente

ESAB

ESAB OCF 2L Manuale utente

ESAB

ESAB Caddy Tig 2200i AC/DC Manuale utente

ESAB

ESAB A2 Multitrac Guida

ESAB

ESAB LAE1000 Manuale utente

ESAB

ESAB AristoMig U400 Manuale utente

ESAB

ESAB ESABMig 400t Manuale utente

ESAB

ESAB migmaster 215 pro Manuale utente

ESAB

ESAB Aristotig 255 AC/DC Manuale utente

ESAB

ESAB A6 Mastertrac Manuale utente

ESAB

ESAB Origo Feed 484 P5 Manuale utente

ESAB

ESAB A6TF F1 Manuale utente

ESAB

ESAB EMP 215ic Manuale utente

Manuali Sistema di saldatura popolari di altre marche

Berner

Berner PLASMACUT 54 Manuale utente

Pro Spot

Pro Spot PR-155 Manuale utente

Forney

Forney 210 Manuale utente

Thermal Arc

Thermal Arc 400S Manuale utente

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuale utente

GYS

GYS PROTIG 201 AC/DC Manuale utente

TAFA

TAFA 30*8B35 Manuale utente

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuale utente

CIGWELD

CIGWELD 636804 Guida rapida

Red-D-Arc

Red-D-Arc DC-400 Manuale utente

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuale utente

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuale utente

WIA

WIA Weldmatic 270 CP132-2 Manuale utente

Sonics

Sonics H520T Manuale utente

Miller

Miller Big Blue 400D Manuale utente

NewArc

NewArc RT2000 Guida rapida

Hypertherm

Hypertherm powermax1000 Manuale utente

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuale utente