ESD electronic CPCI-HD/2 Manuale utente
CPCI-HD/2
HD-Drive, CF-Card Slot
and 2 SATA-Interfaces
Hardware Manual
to Product I.2318.04, I.2318.02
CPCI-HD/2 Hardware Manual • Doc. No.: I.2318.21 / ev. 1.1 Page 1 of 14
esd electronic system design gmbh
Vahrenwalder Str. 207 • 30165 Hannover • ermany
http://www.esd.eu
Phone: +49 (0) 511 3 72 98-0 • Fax: +49 (0) 511 3 72 98-68
N O T E
The information in this document has been carefully checked and is believed to be entirely reliable.
esd makes no warranty of any kind with regard to the material in this document, and assumes no
responsibility for any errors that may appear in this document. In particular descriptions and
technical data specified in this document may not be constituted to be guaranteed product features
in any legal sense.
esd reserves the right to make changes without notice to this, or any of its products, to improve
reliability, performance or design.
All rights to this documentation are reserved by esd. Distribution to third parties, and reproduction
of this document in any form, whole or in part, are subject to esd's written approval.
© 2013 esd electronic system design gmbh, Hannover
esd electronic system design gmbh
Vahrenwalder Str. 207
30165 Hannover
Germany
Phone: +49-511-372 98-0
Fax: +49-511-372 98-68
E-Mail: [email protected]
Internet: www.esd.eu
Trademark Notices
CompactFlash® is a registered trademark of the SanDisk Corporation in the United States.
CompactPCI® is a registered trademark of the PCI Industrial Computers Manufacturers Group.
The PICMG® name and logo are registered trademarks of the PCI Industrial Computer Manufacturers Group.
All other trademarks, product names, company names or company logos used in this manual are reserved by their
respective owners.
Page 2 of 14 Hardware Manual • Doc. No.: I.2318.21 / ev. 1.1 CPCI-HD/2
Doc ment file: I:\Texte\Doku\MANUALS\CPCI\HD2\Englisch\CPCI-HD2_Hardware_en_11.odt
Date of print: 2013-08-22
Doc ment type
n mber: DOC0800
Hardware version: CPCI-HD/2 ev.1.0
Doc ment History
The changes in the document listed below affect changes in the hardware as well as changes in
the description of the facts, only.
Revision Chapter Changes vers s previo s version Date
1.1
- Editorial revision
2013-08-22
- Safety Information inserted
2.6 Software driver support revised
3. Safety notes inserted, chapter revised
7. Declaration of Conformity inserted
8. Chapter “Order Information” removed from chapter 2.7
Technical details are subject to change without further notice.
CPCI-HD/2 Hardware Manual • Doc. No.: I.2318.21 / ev. 1.1 Page 3 of 14
Safety Instr ctions
● When working with CPCI-HD/2 follow the instructions below and read the manual carefully to protect yourself from
injury and the CPCI-HD/2 from damage.
● The device is a built-in component. It is essential to ensure that the device is mounted in a way that cannot lead to
endangering or injury of persons or damage to objects.
● The device has to be securely installed in the control cabinet before commissioning.
● Protect the CPCI-HD/2 from dust, moisture and steam.
● Protect the CPCI-HD/2 from shocks and vibrations.
● The CPCI-HD/2 may become warm during normal use. Always allow adequate ventilation around the CPCI-HD/2 and
use care when handling.
● Do not operate the CPCI-HD/2 adjacent to heat sources and do not expose it to unnecessary thermal radiation. Ensure
an ambient temperature as specified in the technical data.
● Do not use damaged or defective cables to connect the CPCI-HD/2.
● In case of damages to the device, which might affect safety, appropriate and immediate measures must be taken, that
exclude an endangerment of persons and objects.
● Current circuits which are connected to the device have to be sufficiently protected against hazardous voltage (SELV
according to EN 60950-1).
● The CPCI-HD/2 may only be driven by power supply current circuits, that are contact protected.
A power supply, that provides a safety extra-low voltage (SELV or PELV) according to EN 60950-1, complies with this
conditions.
Attention !
Electrostatic discharges may ca se damage to electronic components.
To avoid this, please perform the steps described on page 10 before you touch the CPCI-HD/2, in order to
discharge the static electricity from your body.
Q alified Personal
This documentation is directed exclusively towards personal qualified in control and automation engineering.
The installation and commissioning of the product may only be carried out by qualified personal, which is authorized to
put devices, systems and electric circuits into operation according to the applicable national standards of safety
engineering.
Conformity
The CPCI-HD/2 is an industrial product and meets the demands of the EU regulations and EMC standards printed in the
conformity declaration at the end of this manual.
Warning: In a residential, commercial or light industrial environment the CPCI-HD/2 may cause radio interferences in
which case the user may be required to take adequate measures.
Intended Use
The intended use of the CPCI-HD/2 is the operation as CompactPCI mass memory board.
The guarantee given by esd does not cover damages which result from improper use, usage not in accordance with
regulations or disregard of safety instructions and warnings.
● The CPCI-HD/2 is intended for installation in a CompactPCI system only.
● The operation of the CPCI-HD/2 in hazardous areas, or areas exposed to potentially explosive materials is not
permitted.
● The operation of the CPCI-HD/2 for medical purposes is prohibited.
Service Note
The CPCI-HD/2 does not contain any parts that require maintenance by the user. The CPCI-HD/2 does not require any
manual configuration of the hardware.
Disposal
Devices which have become defective in the long run have to be disposed in an appropriate way or have to be returned
to the manufacturer for proper disposal. Please, make a contribution to environmental protection.
Page 4 of 14 Hardware Manual • Doc. No.: I.2318.21 / ev. 1.1 CPCI-HD/2
Table of contents
1. Overview...................................................................................................................................... 6
2. Technical Data............................................................................................................................. 7
2.1 General Technical Data.........................................................................................................7
2.2 CompactPCI Bus...................................................................................................................7
2.3 HDD Interface........................................................................................................................ 8
2.4 CompactFlash Interface.........................................................................................................8
2.5 Interfaces for External Drives.................................................................................................8
2.6 Software Driver Support.........................................................................................................9
3. Hardware Installation.................................................................................................................. 10
4. LEDs.......................................................................................................................................... 11
4.1 Position of the LEDS............................................................................................................11
4.2 LED Indication..................................................................................................................... 11
5. Connector Assignment...............................................................................................................12
5.1 SATA Interface for external Drives.......................................................................................12
6. Declaration of Conformity...........................................................................................................13
7. Order Information....................................................................................................................... 14
CPCI-HD/2 Hardware Manual • Doc. No.: I.2318.21 / ev. 1.1 Page 5 of 14
Overview
1. Overview
Fig re 1: Block circuit diagram
The module CPCI-HD/2 is a CompactPCI® board in 3 U form factor (4 HP). It is equipped with the
SATA-Controller SIL3114 that supports four SATA-channels. Two channels are used as Serial
ATA interfaces, one channel is used to control a CompactFlash® slot and one channel to control
the local 2.5” HD drive. In the CPCI-HD/2 standard version (order No.: I.2318.04) the hard disk is
included in the scope of delivery. The factory installed HD capacity may change upwards with the
improvement of drive technology.
The board is equipped with a type I CompactFlash card holder. The CF-card slot is located in the
front panel. The interface is ‘hot-pluggable’. Data access is executed in ‘True IDE mode’.
Two external devices can be attached via two on-board SATA plugs. Modification to rear I/O-
connection is possible on request.
LEDs in the front panel indicate the status of the interfaces.
Page 6 of 14 Hardware Manual • Doc. No.: I.2318.21 / ev. 1.1 CPCI-HD/2
CompactPCI Connector
IDE0
IDE-
CompactFlash
Slot
IDE1
SATA/
Parallel ATA
Bridge
SATA/
Parallel ATA
Bridge
SATA0
SATA Lin
4-Port
PCI Host
Controller
SiI3114
IDE Connector
SATA0 Interface
(state display
via LED SATA1)
On-Board
Hard Dis Drive
SATA1 Interface
(state display
via LED SATA2)
(in Legacy Mode:
Legacy Primary
Master Device)
SATA1
(in Legacy Mode:
Legacy Primary
Master Device)
SATA2
(in Legacy Mode:
Legacy Primary
Slave Device)
SATA3
(in Legacy Mode:
Legacy Primary
Slave Device)
Technical Data
2. Technical Data
2.1 General Technical Data
Power supply voltage via CompactPCI-Bus,
nominal supply voltages: 3,3 V / 80 mA
5 V / 1,5 A (starting current,
typ. with 40 GB HDD),
5 V / 0,6 A (quiescent current)
Connectors SATA0 (7-pin Serial ATA-connector, angled, X0)
- SATA0 interface for external drive
SATA1 (7-pin Serial ATA-connector, angled, X1)
- SATA1 interface for external drive
IDE (44-pin IDE-connector, male, X2)
- interface for local HDD, 2 mm grid
CompactFlash (50-pin AMP-C-FLASH male connector X3)
- CompactFlash slot
CPCI (132-pin male connector, X100)
- CompactPCI-board connector
test- and programming only:
JTAG, Debug (8-pin micro plug X4)
Temperature range 0 °C ... 50 °C ambient temperature
Humidity max. 90%, non-condensing
Dimensions 3 U, 4 HP
Weight approx. 150 g without HDD
Table 1: General data of the module
2.2 CompactPCI B s
Host bus PCI bus according to PCI Local Bus Specification, ev. 2.0
PCI-data/address bus 32 bit, 33/66 MHz
PCI + SATA controller SIL3114
Board Dimension according to CompactPCI Specification, ev. 2.0
Connectors
Connector coding no colour coding
universal board (3.3 V or 5 V signal voltage tolerant)
Table 2: CompactPCI Bus
CPCI-HD/2 Hardware Manual • Doc. No.: I.2318.21 / ev. 1.1 Page 7 of 14
Technical Data
2.3 HDD Interface
Number of local drives 1
Data transfer mode Ultra DMA 6
ATA-device bridge SIL 3811
HDD type 2.5”-HD drive, capacity ≥ 40 Gbyte (article I.2318.04 only)
HDD connector 44-pin IDE, 2 mm grid
Table 3: HDD interface
2.4 CompactFlash Interface
Number of CF-interfaces 1 CompactFlash slot
Data transfer mode Ultra DMA 6
ATA-device bridge SIL 3811
CompactFlash according to CompactFlash Specification, Type I CF-card slot,
‘True IDE Mode’, 3.3 V supply voltage, ‘hot-pluggable’
Table 4: CompactFlash interface
2.5 Interfaces for External Drives
Number of interfaces 2
Data transfer mode SATA 1 (1,5 Gb/s)
Controller SIL 3811
Connector 7-pin Serial ATA-connector, angled
modification to ear-I/O connection available on request
Table 5: CompactFlash interface
Page 8 of 14 Hardware Manual • Doc. No.: I.2318.21 / ev. 1.1 CPCI-HD/2
Technical Data
2.6 Software Driver S pport
Operating System S pported Versions
Linux® from Kernel 2.6.19 (requires ‘Silicon Image SATA Support’ in Kernel),
driver contained in standard Kernel
Note: ‘hot-plug’ supported
Windows® The hardware is supported by standard Silicon Image Sil3114 controller
device drivers for Windows. They can be downloaded via the Silicon Image
Support Library (http://www.siliconimage.com/support). As Silicon Image
does not support end users directly please contact our esd suppor-team
([email protected]) in case of problems.
Note: ‘hot-plug’ supported
QNX® from version 6.x, driver contained in standard Kernel
VxWorks® I.2318.31:
VxWorks driver in source code + documentation in source code
CPCI-HD/2 Hardware Manual • Doc. No.: I.2318.21 / ev. 1.1 Page 9 of 14
Hardware Installation
3. Hardware Installation
Read the safety instr ctions at the beginning of this doc ment caref lly, before
yo start with the hardware installation!
Danger!
Electric shock risk. Never carry out work while power supply voltage is switched on!
Attention !
Electrostatic discharges may cause damage to electronic components. To avoid this,
please discharge the static electricity from your body by touching the metal case of the
CompactPCI system before you touch the CPCI-HD/2.
Proced re:
1. Switch off your CompactPCI system and all connected peripheral devices (monitor, printer,
etc.).
2. Discharge your body as described above.
3. Disconnect the computer from the mains.
If the computer does not have a flexible mains cable, but is directly connected to mains,
disconnect the power supply via the safety fuse and make sure that the fuse cannot switch
on again unintentionally (i.e. with caution label).
Danger!
Never carry out work while power supply voltage is switched on!
4. Select an open 3U-CompactPCI bus slot. The CPCI-HD/2 can be inserted into any 3U-slot.
5. Insert the CPCI-HD/2 module into the selected CompactPCI slot.
Carefully push the board until it snaps into place.
6. Fix the CPCI-HD/2.
7. Connect the CompactPCI system to mains again (mains connector or safety fuse).
8. Switch on the CompactPCI system and the peripheral devices.
9. Now you can configure the HDD and the CompactFlash. Please read the documentation of
your operating system for more information.
Page 10 of 14 Hardware Manual • Doc. No.: I.2318.21 / ev. 1.1 CPCI-HD/2
Indice
Altri manuali ESD electronic Hardware per computer
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
