Estes ASRAAM PYTHON 4 EST 2054 Manuale utente

FIN

UPPER TUBE MARKING GUIDE

MATCH LINES

ESTES® INDUSTRIES

1295 H Street

Penrose, CO 81240

PRINTED IN CHINA

www.estesrockets.com

PARTS:

Locate the parts shown below and lay them

out on the table in front of you.

DO NOT USE THIS DRAWING TO

ASSEMBLE YOUR ROCKET.

ASSEMBLY TIP:

Read all instructions

before beginning work on

your model. Make sure

you have all parts and

supplies.

KEEP FOR FUTURE REFERENCE.

FLYING MODEL ROCKET KIT INSTRUCTIONS

EST 2054/1245

TEST-FIT ALL PARTS

TOGETHER BEFORE

APPLYING ANY GLUE!

If any parts don’t fit properly, sand

as required for precision assembly.

Die Cut Card Fin Conduit (1) (32907)

Centering Ring Card (1)

(30126)

Die Cut Balsa Sheet (2) (32216)

Operation Enduring

Freedom sticker (1)

(60586)

SUPPLIES In addition to the parts included in the kit you will also need:

SCISSORS PENCIL RULER FINE

SAND PAPER

(#400-600 GRIT)

CARPENTER’S

GLUE

MASKING

TAPE SPRAY

PRIMER

WHITE

SPRAY PAINT:

OLIVE

DRAB, LT. GREY

PLASTIC

CEMENT

MODELING

KNIFE SPRAY

DULL

COAT

RAZOR SAW SILVER PAINT

PEN

Upper Body Tube BT-55

(1) (30375)

Main Body Tube BT-55

(1) (30374)

Assembled 12” (30 cm)

Parachute

(1) (35801)

Engine Hook (1)

(35021)

Clay Weight (1)

(85704)

Red Tube Coupler (1)

JT-55 (30175-5)

Decal Sheet (1) (60554)

HELPFUL HINT:

IF NOSE CONE/COUPLER FIT IS. . .

TOO

TIGHT

TOO

LOOSE

ADD

MASKING TAPE. SAND FOR FIT.

Shock Cord (1)

1/8" x 18"

(38374)

Mylar Retainer

Ring (1)

(30168)

Green Engine

Block (1)

(30162-2)

Yellow Spacer Tool (1)

(35003)

Nose Cone (1)

(60552)

Plastic Tail Cone and

Adapter (1)

(60568)

Launch Lug (1)

(38175)

SHOCK CORD

MOUNT

SECTION 3

SECTION 2

SECTION 1

Engine Mount Tube

BT-20 (1) (30327)

FIN

LAUNCH

LUG

LOWER TUBE MARKING GUIDE

SHOCK CORD

MOUNT

SECTION 3

SECTION 2

SECTION 1

1. ASSEMBLING ENGINE MOUNT

I" mark

(25 mm)

B. STACK LIKE PIECES AND SAND

EDGES SMOOTH. LEAVE THE EDGES

SQUARE, DO NOT ROUND

THEM.

A. FINE SAND BALSA SHEETS. CAREFULLY CUT

PARTS FREE WITH A MODELING KNIFE.

2. PREPARING FINS

1" mark

(25 mm)

1" mark

(25 mm)

A. MEASURE AND MARK

YELLOW SP ACER TOOL. B. USE SCRAP BALSA TO SMEAR GLUE

2" (51 MM) INSIDE ENGINE MOUNT

TUBE.

C. PUSH ENGINE BLOCK INTO BT-20 ENGINE

MOUNT TUBE WITH SPACER TOOL UP

TO MARK. REMOVE SPACER TOOL.

F. TEMPORARILY TAPE

HOOK INTO PLACE.

G. CAREFULLY REMOVE

RINGS FROM CARD.

H. APPLY GLUE ABOVE

THE 1" (25 MM) LINE.

I. SLIDE MYLAR RETAINER RING

ONTO ENGINE MOUNT TUBE UP

TO 1" (25 MM) MARK. LET DRY.

J. PLACE A PENCIL MARK AT 2 1/2" (64 MM)

AND 4 7/8 (124 MM) FROM END OF ENGINE

MOUNT. REMOVE TAPE.

K. SLIDE A CENTERING RING

DOWN TO THE 2 1/2" (64 MM)

MARK.

YELLOW SPACER

TOOL

1/2”

(13 mm)

REAR

2 1/2 (64 mm)

4 7/8 (124 mm)

L. SLIDE A CENTERING RING DOWN

TO THE 5 7/8" (149 MM) MARK. M. APPLY GLUE FILLETS TO BOTH

SIDES OF EACH CENTERING

RING. LET DRY.

GLUE

(51 mm)

SCRAP BALSA

Remove

Immediately.

D. MARK ENGINE MOUNT TUBE AT 1" (25 MM)

AND 2 1/4" (57 MM) FROM REAR END. CUT

1/8" (3 MM) SLIT AT 2 1/4" (57 MM) MARK.

GREEN

ENGINE

BLOCK

MARK

YELLOW SPACER

TOOL

1/2"

(13 mm)

REAR

GLUE

MYLAR

RING

ENGINE MOUNT

TUBE

(25 mm)

2 1/4"

(57 mm)

E. POSITION

ENGINE HOOK.

3. MARKING BODY TUBES

A. CUT OUT

TUBE

MARKING

GUIDE.

D. EXTEND ALL LINES

ENTIRE LENGTH OF

TUBE. Top view

Door

Frame

Upper Body Tube

8 5/8” (219 mm)

Lower Body Tube

10 3/4” (273 mm)

FIN

LAUNCH

LUG

UPPER TUBE MARKING GUIDE

ASRAAMPYTHON4 EST2054

SHOCK CORD

MOUNT

SECTION

SHOCK CORD

MOUNT

SECTION

LOWER TUBE MARKING GUIDE

FIN

TUBEMARKINGGUIDE

TCHLINES

“LL”

C.WRAP TUBE MARKING

GUIDE AROUND

UPPER BODY TUBE

AND MARK AT

ARROWS. EXTEND

LINES ENTIRE

LENGTH OF TUBE.

B. WRAP TUBE MARKING

GUIDE AROUND LOWER

BODY TUBE AND MARK AT

ARROWS. EXTEND LINES

ENTIRE LENGTH OF TUBE.

MARK LAUNCH LUG LINE

WITH “LL”.

SQUARE END

GLUE

ROUNDED

END

1 1/2” MARK

(38 mm)

D. STAND ROCKET ON

FLAT TABLE UNTIL

GLUE DRIES

COMPLETELY.

"LL"

PLASTIC

CEMENT

4. PREPARE TAIL CONE AND ADAPTER

DISCARD

SAND EDGES SMOOTH

A. TEST FIT FINS IN SLOTS. SAND AS NEEDED

FOR PROPER FIT. APPLY CARPENTER'S GLUE

TO FIN AND TAB EDGE.

C. CHECK ALIGNMENT OF FINS

AS SHOWN. ALLOW GLUE

TO SET.

NOTE:

FIN SHAPE AND TAB LOCATION.

TAIL CONE AND ADAPTER.

A. USING A RAZOR SAW, CAREFULLY

CUT OFF ENDS AND CUT IN HALF. B. SAND EDGES SMOOTH.

C. CAREFULLY SAW OFF NIBS.

SAND AWAY EXCESS PLASTIC

LIP FLUSH WITH SURFACE.

CUT IN

HALF

NOTE:

FINS MUST BE ATTACHED

CORRECTLY FOR STABLE

FLIGHT.

5. ASSEMBLING ENGINE MOUNT AND TAIL CONE

A. USE FINGER TO SMEAR GLUE 1 3/4"

(45 MM) INSIDE REAR OF BODY

TUBE.

B. ENGINE HOOK MUST

LINE UP WITH LAUNCH LUG

"LL" LINE.

DO NOT CEMENT

TAIL CONE YET!

D. APPLY A GLUE FILLET AROUND

RING AND BODY TUBE JOINT.

LET DRY.

E. APPLY PLASTIC CEMENT

AROUND INSIDE OF BODY

TUBE. ALIGN LAUNCH

LUG LINE BETWEEN FIN

SLOTS ON TAIL CONE.

PUSH TAIL CONE INTO

BODY COMPLETELY. LET

DRY.

FIN SLOT

ENGINE HOOK

FIN SLOTS

REAR VIEW

MAIN BODY TUBE

GLUE

BODY

TUBE

"LL"

FINS SHOULD PROJECT

STRAIGHT FROM THE BODY.

6. ASSEMBLING LOWER FINS

90˚

TAB

CUT OFF

1 3/4”

(45 mm)

GLUE

"LL"

C. INSERT ENGINE

MOUNT INSIDE BODY

TUBE AND PUSH

INTO PLACE WITH

TAIL CONE.

REMOVE TAIL CONE

IMMEDIATELY. LET

DRY.

"LL"

GLUE

B. PUSH FIN INTO TAIL CONE. LET DRY. CONTINUE TO

ASSEMBLE REMAINING FINS. LET DRY.

7. ATTACHING FIN CONDUIT

A. CAREFULLY REMOVE FIN

CONDUIT STRIPS FROM

CARD.

B. MEASURE 1 1/2” (38 MM) FROM

END OF BODY TUBE. MARK THE

FIN LINE ON ALL FOUR LINES.

C.ROUNDED END SQUARE END

FIN CONDUIT

COMPLETED TAIL CONE.

FIN LINE

D. APPLY GLUE TO ONE SIDE OF

FIN CONDUIT, CENTER

CONDUIT ON FIN LINE, MAKE

SURE THE “SQUARE END”

TOUCHES THE 1 1/2” (38 mm)

MARK. LET DRY. CONTINUE

WITH THE REMAINING

CONDUITS. LET DRY.

1 1/2"

(38 mm)

5/8”

(16 mm)

8. ATTACHING BALSA STRIPS

9. PREPARING NOSE CONE

BALSA STRIP

WIDE END

NARROW END

90˚

A. CAREFULLY CLEAN

FLASH FROM NOSE

CONE AND EYELET.

A. APPLY GLUE TO BOTTOM OF BALSA STRIP. WIDE END

TOWARD FINS, POSITION BALSA STRIP CENTER ON FIN

CONDUIT, WIDE END EVEN WITH FIN CONDUIT END.

CAUTION:

BE CAREFUL NOT TO CUT OFF EYELET. CLAY WEIGHT

B. ROLL CLAY INTO SNAKE.

C. INSERT CLAY INTO NOSE

CONE.

D. PACK CLAY TIGHTLY INTO

TIP OF NOSE CONE.

B. COMPLETED

ASSEMBLY.

10. ASSEMBLING TUBE COUPLER

B. APPLY GLUE BAND INSIDE

UPPER BODY TUBE. C. INSERT COUPLER UP TO

5/8” (16mm) MARK.

D. LET DRY.

GLUE

SQUARE END

ROUNDED END

GLUE ON

BOTTOM

WIDE END

NARROW END

5/8”

(16 mm)

COUPLER

UPPER BODY TUBE

GLUE

11.ASSEMBLING UPPER BODY TUBE AND FINS

PARTS IN THIS

ASSEMBLY

WIDE END

GLUEGLUE

UPPER FIN

CONFIGURATION

FRONT

REAR

FRONT

REAR

UPPER FIN LINE

FRONT

REAR

UPPER FIN LINE

A. APPLY GLUE TO EDGE OF FIN,

PLACE ON UPPER FIN LINE. LET

DRY. CONTINUE FOR REMAINING

FINS. LET DRY.

D. COMPLETED UPPER BODY

TUBE ASSEMBLY. FINS

MUST BE STRAIGHT.

A. MARK TUBE COUPLER.

PLASTIC

CEMENT

C. APPLY A BEAD OF PLASTIC

CEMENT INSIDE UPPER

BODY TUBE, INSERT NOSE

CONE. LET DRY.

B. COMPLETED FIN ATTACHMENT.

FIN CONDUIT

ROCKET PREFLIGHT

A. INSERT FOUR-SIX

SQUARES OF

LOOSELY

CRUMPLED

RECOVERY

WADDING INTO

ROCKET BODY

TUBE.

NOTE: Use Estes® Recovery Wadding (EST 302274) only.

C. FOLD. D. ROLL.

B. SPIKE.

PAINT SCHEME

FIRST SPRAY ROCKET WITH WHITE PRIMER, LET DRY AND

SAND. REPEAT UNTIL ROCKET IS SMOOTH. FOLLOW THE

PAINT SCHEME ON THE PACKAGE. WHEN PAINT IS DRY, PEEL DECALS ONE AT A TIME FROM

BACKING SHEETS AND APPLY WHERE SHOWN. RUB DOWN

TO REMOVE BUBBLES.

*OPTIONAL - SPRAY A DULL COAT OVER

THE ENTIRE ROCKET WHEN COMPLETE.

A. LOOP SHROUD LINES. B. PUSH THROUGH

SHOCK CORD LOOP.

C. LOOP PARACHUTE

THROUGH SHROUD LINES.

D. PULL TIGHT.

14. ATTACHING PARACHUTE

SHOCK

CORD LOOP

SHOCK CORD LOOP

SHOCKCORD

MOUNT

SECTION 3

SECTION 2

SECTION 1

SHOCK CORD

MOUNT

SECTION

G. TIE LOOP 3" (76 MM) FROM

SECOND SHOCK CORD

MOUNT.

GLUE

1”

(25 mm)

A. CUT OUT SHOCK CORD

MOUNTS.

12. ATTACHING LAUNCH LUGS

A. CUT LAUNCH LUG IN HALF.

5/8”

(16 mm)

B. APPLY GLUE TO LAUNCH LUG

AND ATTACH ON LAUNCH LUG

LINE 1/8” (3 mm) FROM END OF

TUBE AND 7 7/8” (200 mm)

FROM END OF TUBE. LET DRY.

C. USING CARPENTER’S GLUE, APPLY FILETS

TO THE LAUNCH LUG/BODY TUBE JOINTS.

APPLY FILETS TO BALSA STRIPS AND UPPER

BODY TUBE/FIN JOINTS. SMOOTH WITH

FINGER. LET DRY.

7 7/8”

(200 mm) D. USING PLASTIC CEMENT, APPLY FILLETS TO

REAR FINS/TAIL CONE JOINTS, SMOOTH WITH

FINGER. LET DRY.

PLASTIC

CEMENT

PLASTIC

CEMENT

13. ATTACHING PARACHUTE

B. APPLY GLUE.

FOLD FORWARD.

C. APPLY GLUE.

FOLD FORWARD.

D. SQUEEZE TIGHTLY

AND HOLD FOR ONE

MINUTE.

E. GLUE MOUNT 1” (25 mm)

INSIDE UPPER BODY

TUBE. HOLD UNTIL

GLUE SETS. LET DRY.

(76 mm)

GLUE

Second shock cord mount

GLUE

SHOCK CORD

H. APPLY GLUE TO SECOND SHOCK CORD

MOUNT AND PLACE INSIDE END OF LOWER

BODY TUBE. PRESS FIRMLY. LET DRY.

E.WRAP LINES LOOSELY, INSERT ‘CHUTE,

SHOCK CORD AND UPPER BODY SECTION.

1/8”

(3 mm)

F. CUT OUT

SECOND

SHOCK CORD

MOUNT. FOLD

AND GLUE AS

BEFORE.

COUNTDOWN AND LAUNCH

FLYING YOUR ROCKET

Choose a large field (500 ft. [152 m] square) free of dry weeds and brown grass. The larger

the launch area, the better your chance of recovering your rocket. Football fields and

playgrounds are great. Launch only with little or no wind and good visibility.

Always follow the National Association of Rocketry (NAR) SAFETY CODE.

MISFIRES

TAKE THE KEY OUT OF THE CONTROLLER. WAIT ONE MINUTE BEFORE GOING

NEAR THE ROCKET! Take the plug and igniter out of the engine. If the igniter has burned,

it worked but did not ignite the engine because it was not touching the propellant inside

the engine. Put a new igniter all the way inside the engine without bending it. Push the

plug in place. Repeat the steps under Countdown and Launch.

NAR Safety Code

NO DRY

GRASS

OR WEEDS

PRECAUTIONS

LAUNCH SUPPLIES

(sold separately):

• Porta-Pad®II Launch Pad

• Electron Beam® Launch Controller

• Recovery Wadding

• Igniters (w/ engines)

• Igniter Plugs (w/ engines)

• Recommended Estes®Engines: B4-2,

B4-4, B6-2, B6-4, C6-3, C6-5.

B. Tip must touch

propellant..

F. Insert engine.

D.C.

ENGINE PREP

To avoid serious injury,

read instructions & NAR

Safety Code included with

engines.

PREPARE YOUR ENGINE

ONLY WHEN YOU ARE

OUTSIDE AT THE LAUNCH

SITE PREPARING TO LAUNCH!

If you do not use your prepared

engine, remove the igniter before

storing your engine.

KEY ALWAYS OUT UNTIL

FINAL COUNTDOWN!

HOLD KEY DOWN AND PRESS

LAUNCH BUTTON UNTIL LIFT-OFF!

4...

4... 3... 2...1...

INSERT KEY.

PUSH DOWN

AND HOLD.

1...

LAUNCH

BUTTON

3...

4"(10 cm)

Masking

Tape

15 FT. (5 M)

2...

KEY

Questo manuale è adatto per i seguenti modelli

Altri manuali Estes Giocattolo

Estes

Estes STAR STRIKE Manuale utente

Estes

Estes CLUSTER BOMB BLU-97B EST 2055 Manuale utente

Estes

Estes ORBIS 3D Manuale utente

Estes

Estes Jetliner Manuale utente

Estes

Estes BIG DADDY 2162 Manuale utente

Estes

Estes Alpha 1225 Manuale utente

Estes

Estes 2463 Manuale utente

Estes

Estes Baby Bertha EST 1261 Manuale utente

Estes

Estes SHOCKWAVE 4190 Manuale utente

Estes

Estes STAR STRIKE Manuale utente

Estes

Estes X-15 Series Manuale utente

Estes

Estes GBU-24 PAVEWAY III EST 1247 Manuale utente

Estes

Estes Astrocam 007308 Manuale utente

Estes

Estes EST 2183 Manuale utente

Estes

Estes INTERCEPTOR 1250 Manuale utente

Estes

Estes Converter 2029 Manuale utente

Estes

Estes BLACK DIAMOND Series Manuale utente

Estes

Estes Executioner 1951 Manuale utente

Estes

Estes Copperhead Manuale utente

Estes

Estes Payloader II Manuale utente

Estes

Estes Control Wild Sky 4553 Manuale utente

Estes

Estes SUPER SHOT Series Manuale utente

Estes

Estes GNOME Manuale utente

Estes

Estes V2 Manuale utente

Manuali Giocattolo popolari di altre marche

marklin

marklin 37321 Manuale utente

Canon

Canon PAPER CRAFT Manuale utente

GREAT PLANES

GREAT PLANES Pitts M-12S Manuale utente

NOCH

NOCH 14261 Manuale utente

Hausler

Hausler 450 SE V2 Manuale utente

Dynaflite

Dynaflite Daydream Manuale utente

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuale

Kenner

Kenner Batman 63651 Manuale utente

LEGO

LEGO 8527 Manuale utente

iKarus

iKarus ECO 8 Manuale utente

Multiplex

Multiplex EasyStar II Manuale di istruzioni

Walkera

Walkera 38 Manuale di istruzioni

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuale utente

MD MXION SWD Manuale utente

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuale utente

marklin

marklin 39671 Manuale utente

Meccano

Meccano 15103 Manuale utente

LEGO

LEGO TECHNIC 8735 Manuale utente