Estes Sky Writer Manuale utente
SHOCK CORD
MOUNT
SECTION 3
SECTION 2
SECTION 1
ESTES® INDUSTRIES
1295 H Street
Penrose, CO 81240
PRINTED IN CHINA
www.estesrockets.com
SUPPLIES REQUIRED:
ALL GLUED AREAS ARE SHADED IN GRAY
HOBBY KNIFE PLASTIC
CEMENT CARPENTER’S
GLUE PENCIL RULER SCISSORS FINE
SAND PAPER
(#400-600 GRIT)
MASKING
TAPE
FLYING MODEL ROCKET KIT INSTRUCTIONS
HELPFUL HINT:
IF NOSE CONE/COUPLER FIT IS. . .
TOO
TIGHT
TOO
LOOSE
ADD
MASKING TAPE. SAND FOR FIT.
Black Engine
Holder Ring (1)
(30120-3)
Blue Engine
Mount Tube (1)
(30326-1)
Fin Unit (1)
72614
Launch Lug (1)
(38175)
Red Tube
Coupler (1)
(30174-5)
Decal Sheet (1)
(60160)
Assembled 12” (30 cm) Parachute
(35801)
Lower Body Tube - BT-50 (1)
(60158) Upper Body Tube - BT-50 (1)
(30349)
Nose Cone (1)
(71027)
Green Engine
Block (1)
(30162-2)
PARTS:
Locate the parts shown below and lay them out on the table in front
of you. DO NOT USETHIS DRAWINGTOASSEMBLE YOUR ROCKET.
KEEP FOR FUTURE REFERENCE.
SPRAY CLEAR
COAT
(OPTIONAL)
NO.2
Green Adaptor
Ring (1)
(30165-2)
ASSEMBLY TIP
Read all instructions before beginning work on your model.Make sure
you have all parts and supplies. TEST-FITALL PARTS TOGETHER
BEFORE APPLYING ANY GLUE. If any parts don’t fit properly, sand
as required for precision assembly.
FOR KITS:
EST 1235
EST 1260
Engine Hook (1)
(35021)
Shock Cord (1)
(38374)
1”
(25 mm)
2.
3.
4.
B. Cut a 1/8” (3 mm) wide
slit with Hobby Knife at
the 2 1/2” (63.5 mm)
mark.
C. Position Engine Hook.
D. Apply glue just
in front of 1"
(25 mm) mark.
1.
1/8”
(3 mm)
GLUE
E. Slide Black Retainer
Ring onto Engine
Mount Tube to the
1” (25 mm) mark.
F. Apply glue inside front of
Engine Mount Tube.
GLUE
G. Insert Green Engine Block inside
Engine Mount Tube until it contacts
Engine Hook. Let Dry. Finished Assembly
A.
1/2”
(13 mm) REDTUBE
COUPLER
C. Hold Engine Mount Assembly
in place with thumb. In one
continuous movement slide
Green Adapter Ring onto
Engine Mount until it touches
Fin Unit. Let glue dry.
C. Apply glue band inside forward end
of Lower Body Tube Assembly.
B. Lightly scratch a 1" x 1/8" (25 mm x 3 mm) area
of the Body Tube with a hobby knife.
C. Glue Launch Lug onto Body Tube.
Let glue set. D. Apply glue fillet on each side of Launch
Lug. Smooth with finger and let dry.
page 2
ENGINE MOUNT ASSEMBLY
Blue Engine
Mount Tube
A.
A. Locate slot in the Fin Unit. Align Engine
Hook of Engine Mount Assembly with slot
in Fin Unit and slide in place until it stops.
3/8” (10 mm)
GLUE
D. Apply glue inside Lower Body Tube
as shown. Push Body Tube over
Green Adaptor Ring in one
continuous motion, until Body Tube
touches Fin Unit.
B.Apply glue band around inside of Upper Body
Tube and insert Red Tube Coupler up
to 1/2” (13 mm) mark Let glue set.
ATTACHING
LAUNCH LUG
A. Use a ruler to reference a straight line up from
the Engine Hook. Make a small mark on body
tube 5-1/2” (14 cm) up from end of Fin Unit.
GREEN
ADAPTER
RING
2 1/2”
(63.5 mm)
MARK
FIN UNIT ASSEMBLY
SLOT
B.Apply glue around Engine
Mount Assembly as shown.
1/2” (13 mm)
GLUE
BODYTUBE
ASSEMBLY
1/2” (13 mm) mark
ENDS
EVEN
D. Slide over Red Tube Coupler.
Let Dry.
GLUE
REDTUBE
COUPLER
GLUE
GLUE
ALIGNWITH
ENGINE HOOK
5 1/2”
(14 cm)
5.
A. Cut out Shock Cord
Mount from front page.
SHOCK CORD
MOUNT
SECTION
3
SECTION
2
SECTION
1
Glue Mount inside BodyTube.Hold
until glue sets.Let glue dry
completely.
6.
D.
Squeeze
Tightly. E.
32
1
B.
Fold
Forward.
Shock Cord
D. Pass Parachute
through loop.
C. Push loop through
eyelet of Nose
Cone.
A. Remove FLASH from
eyelet of Nose Cone.
SHOCK CORD
ROCKET PREFLIGHT
B. Spike.
A. Insert 3-4 loosely crumpled
squares of RecoveryWadding. E. Wrap lines loosely, insert
Parachute, Shock Cord and
Nose Cone.
C. Fold.
D. Roll.
CAUTION:
DO NOT CUT OFF
EYELET OF NOSE CONE.
page 3
ATTACHING SHOCK CORD
C. 3
Smear Glue.
Smear Glue.
ATTACHING PARACHUTE & SHOCK CORD
7. DECAL APPLICATION
OPTIONAL: Clear coat entire rocket after applying decal.
Carefully remove Decal from sheet and apply where
shown.Rub down to remove bubbles.
B. Form loop with
Shroud Lines.
DOUBLE
KNOT
DECAL
PULL
TIGHT
E. Pull Parachute tight.Tie Shock
Cord to eyelet of Nose Cone with
a double knot.
2”
(51 mm)
YES
NO
COUNTDOWN AND LAUNCH
NAR Safety Code
NO DRY GRASS
OR WEEDS
PRECAUTIONS
HOLD KEY DOWN AND PRESS LAUNCH
BUTTON UNTIL LIFT-OFF!
15 FT. (5 M)
MASKING
TAPE
INSERT KEY.
PUSH DOWN
AND HOLD.
FLYINGYOUR ROCKET
Choose a large field (500 ft. [152 m] square) free of dry weeds and
brown grass.The larger the launch area, the better your chance of
recovering your rocket. Football fields and playgrounds are great.
Launch only with little or no wind and good visibility.
Always follow the National Association of Rocketry (NAR)
SAFETY CODE.
MISFIRES
TAKE THE KEY OUT OF THE CONTROLLER. WAIT ONE MINUTE
BEFORE GOING NEAR THE ROCKET! Disconnect the igniter clips and
remove the engine. Take the plug and igniter out of the engine. If the igniter
has burned, it worked but did not ignite the engine because it was not
touching the propellant inside the engine. Put a new igniter all the way
inside the engine without bending it. Push the plug in place. Repeat the
steps under Countdown and Launch.
©2001 Centuri Corp.All rights reserved. (12/01) PN 60161
4...
4...
1...
1... 3...
3...
LAUNCH SUPPLIES
•Estes® Porta Pad® II Launch
Pad and Electron Beam® Controller
•Recovery Wadding
•Igniters (with Engines)
•Igniter Plugs (with Engines)
•Estes® Recommended Engines:
A8-3, B4-2, B4-4, B6-4, C6-5
(Sold Separately)
ENGINE PREP
A. B. Tip must touch
propellant. F. Insert Engine.
D.
C. E.
page 4
4”(10.1 cm)
KEY ALWAYS OUT
UNTIL FINAL
COUNTDOWN!
2...
2...
4... 3...2...1...
5...
5...
LAUNCH
BUTTON
Indice
Altri manuali Estes Giocattolo
Estes
Estes Control Mad Cat 4608 Manuale utente
Estes
Estes GBU-24 PAVEWAY III EST 1247 Manuale utente
Estes
Estes SHOCKWAVE 4190 Manuale utente
Estes
Estes V2 Manuale utente
Estes
Estes STAR STRIKE Manuale utente
Estes
Estes Astrocam 007308 Manuale utente
Estes
Estes Payloader II Manuale utente
Estes
Estes STM-012 Series Manuale utente
Estes
Estes STAR STRIKE Manuale utente
Estes
Estes Control Wild Sky 4553 Manuale utente
Estes
Estes GNOME Manuale utente
Estes
Estes ORBIS 3D Manuale utente
Estes
Estes Alpha 1225 Manuale utente
Estes
Estes INTERCEPTOR 1250 Manuale utente
Estes
Estes Executioner 1951 Manuale utente
Estes
Estes X-15 Series Manuale utente
Estes
Estes EST 2183 Manuale utente
Estes
Estes Baby Bertha EST 1261 Manuale utente
Estes
Estes 2231 Manuale utente
Estes
Estes BLACK DIAMOND Series Manuale utente
