EtherWAN EX83304 Series Manuale utente
EX77
Copyright 2019 EtherWAN Systems, Inc. Page 1
All Rights Reserved
EX83304 Series Hardened Managed Ethernet Switch
EX83304
06/13/2019
Installation Guide
W70G-EX83304Q1
1 Unpacking
Unpack the items. Your package should include:
One EX83304 Series hardened managed switch
One console cable
If items are missing or damaged, notify your
EtherWAN representative. If possible, save the
carton and packing material. The full product
manual can be downloaded from:
https://www.etherwan.com
2 What Else You Need
Shielded twisted pair cables and
corresponding shielded RJ45 connectors
Appropriate SFP cable for SFP ports
Personal computer with a DB9 straight cable
(if switch is to be managed through console
port)
3 Select a Location
Installations: DIN-Rail mount, wall (in an
enclosure or industrial panel)
Identify a power source within 6 feet (1.8
meters).
Choose a dry area with ambient
temperature between -40 and 75ºC (-40 and
167ºF).
Be sure there is adequate airflow.
4 Connect to the Data Ports
Depending on the model, your switch can have
the following ports:
12 or 8 10/100BASE-TX ports
2 or 4 Gigabit SFP slots
10/100BASE-TX Ports
These ports come in 10/100Base-TX interfaces.
They can connect to devices such as an IP
surveillance camera or a Voice Over Internet
Protocol (VoIP) phone.
1 Gbps SFP Ports
Your switch model has four 1 Gbps SFP slots. SFP
transceivers can be installed directly into ports
13 –16. Ensure that the same type of transceiver
is used at both ends of the link and that the
correct type of fiber cable is used.
5 Apply Power
The switch has two pairs of power inputs:
A 12-48 VDC terminal block
The power dissipation under full load is as
follows:
12V/1.44A 24V/0.67A 48V/0.33A
Redundant power supply is supported. However,
only one power input is required to operate the
switch.
Note: Use qualified power supply by SELV or
double insulation of UL60950 or UL61010-1 or
UL61010-2-201 standards.
Terminal Block
The switch provides two power inputs on a 12-
48VDC terminal block. Only one power input is
required to operate the switch. The terminal
block has 5 terminal posts.
Copyright 2019 EtherWAN Systems, Inc. Page 2
All Rights Reserved
EX83304 Series Hardened Managed Ethernet Switch
EX83304
06/13/2019
Installation Guide
hernet Switch
W70G-EX83304Q1
Pin
Description
Power 1
12-48VDC
Power Ground
Power 2
12-48VDC
Power Ground
Earth Terminal
Relay Output Rating
2A @ 30VDC
Relay Output Alarm
The relay output can be connected to an alarm
signaling device. Current is 2A at 30VDC.
Power-Up Sequence
When the switch is powered up:
All Link/ACT LEDs blink momentarily.
The Power 1, 2 LEDs light up and stay lit.
LEDs for every port connected to a device
will flash, as the switch conducts a brief
Power On Self-Test (POST).
6 Console Configuration
Connect to the switch console by
connecting the DB9 cable to the console
port of the switch and to the serial port of
the computer running a terminal emulation
application (such as HyperTerminal or
Putty).
Configuration settings of the terminal-
emulation program: Baud rate: 115,200bps,
Data bits: 8, Parity: none, Stop bit: 1, Flow
control: none.
The default login name is “root,” no
password.
7 Web Configuration
Log in to the switch by launching a web
browser and entering 192.168.1.10 in the
address bar.
Enter the default login ID: root (no
password) and click “Login.” The system
information screen will display.
8 Other information
DIN-Rail Assembly Startup, and Dismantling
Assembly: Place the Switch on the DIN rail
from above using the slot. Push the front of
the Switch toward the mounting surface
until it audibly snaps into place.
Startup: Connect the supply voltage to
start up the Switch via the terminal block.
Dismantling: Pull out the lower edge and
then remove the Switch from the DIN rail.
Power wiring information:
Use cable type - AWG (American Wire Gauge) 18-
24 and corresponding pin type cable terminals.
Using torque value 1.7 lb-in, do not use excessive
force when fixing wiring.
The rating of the power wire used must be
at least 105°C.
Label clean up:
Indoor use and pollution degree II, it must
be wiped with a dry cloth for clean up the
labelling.
If the equipment is used in a manner not
specified by the manufacturer, the
protection provided by the equipment may
be impaired.
The Ethernet switch shall be mounted in the
Industrial Control Panel and ambient
temperature should not exceed 75 °C.
Manufacturer information:
ETHERWAN SYSTEMS, INC.
4F-7, No. 79, Sec. 1, Xintai 5th Road, Xizhi
District, New Taipei City 221, Taiwan
Altitude up to 2000 m
Indoor use only
Humidity range (Operational): 5% to 95%,
non-condensation
Altri manuali EtherWAN Interruttore
EtherWAN
EtherWAN ER59000 Series Manuale utente
EtherWAN
EtherWAN InfraGreEn IG5 Manuale utente
EtherWAN
EtherWAN EX72129A Manuale utente
EtherWAN
EtherWAN EX32908 series Manuale utente
EtherWAN
EtherWAN EX42300 series Manuale utente
EtherWAN
EtherWAN OttoE TF100 Sereis Manuale utente
EtherWAN
EtherWAN EX77000 Series Manuale utente
EtherWAN
EtherWAN EX78000 Series Manuale utente
EtherWAN
EtherWAN EX19162A Manuale utente
EtherWAN
EtherWAN EX45000 Series Manuale utente
EtherWAN
EtherWAN EX48050-00B Manuale utente
EtherWAN
EtherWAN EX77964 Manuale utente
EtherWAN
EtherWAN EX29000 Manuale utente
EtherWAN
EtherWAN EX42914 Series Manuale utente
EtherWAN
EtherWAN EX42908 series Manuale utente
EtherWAN
EtherWAN EX46910 Manuale utente
EtherWAN
EtherWAN EX33000 Series Manuale utente
EtherWAN
EtherWAN EX19164 Manuale utente
EtherWAN
EtherWAN EX78000 Series Manuale utente
EtherWAN
EtherWAN EX17016 Manuale utente
