ETOE A1212 Manuale utente
EN
01 - 14
Catalog
English
01
Read all instructions before you use this device. Do not make any changes
that are not described in this manual. If physical injury, loss of data, or
damage is caused by failure to follow instructions, the warranty does not
apply.
• To reduce the risk of fire and/or electric shock, do not expose the
device to rain or moisture, and objects filled with liquids, such as vases,
should not be placed on the device.
• Do not place the device on soft surfaces such as tablecloths or carpets
as doing so could be a fire-hazard.
• Do not place the device in areas susceptible to excessive dust and dirt
or near any appliance generating a strong magnetic field.
• To prevent overheating, do not block or clog the ventilation openings.
Never place the device in a confined space. Always leave enough
space around the device for ventilation.
• Protect the device against direct sunlight, heat, large temperature
fluctuations and moisture.
• When the device runs for a long period of time and the surface
becomes hot, shut it down and unplug the power cord. Resume
operation only after the device has cooled.
• Always handle the device with care. Avoid touching the lens.
• Never place heavy or sharp objects on the device or the power cord.
To avoid electric shock, do not disassemble.
• Only use attachments or accessories specified by the manufacturer.
Avoid extreme vibration. It may damage the internal components.. Do
not allow children to handle the device without supervision.
• Under the following conditions, a layer of moisture can appear inside
the device which can lead to malfunctions:
a) if the device is moved from a cold to a warm area;
b) after a cold room is heated;
c) when the device is placed in a damp room.
To avoid any moisture, seal the device in a plastic bag before moving it
to another room, and wait for one to two hours before you take it out of
the bag.
Setup
Safrty Instructions
02
• Use only the provided power adapter.
• Power off the device before removing the power supply from the socket.
• Protect the power cord from being walked on or pinched, particularly at
plugs, convenience receptacles, and the point where they exit from this
device.
• Unplug this device if there are lightning storms or when unused for a long
period of time.
• Where the power plug or an appliance coupler is used as the disconnect
device, the disconnect device shall remain readily operable.
• Before you make or change any connections, ensure that all devices are
disconnected from the power outlet.
• Do not touch the power cable or the power connector with wet hands.
To avoid hearing damage, do not listen for extended periods at high
volume. Set the volume at a safe level.
• Power off the device and remove it from the power supply before cleaning
the surface.
• Use a soft, lint-free cloth. Never use liquid, gaseous, or easily flammable
cleansers (like sprays, abrasives, polishes, and alcohol). Wipe over the
surfaces gently. Be careful that you do not scratch the surfaces.
• Do not use any liquid cleaning agents to clean the lens as they may
damage the protective coating on the lens. Use lens cleaning paper to
clean the lens of the projector.
• Do not make any repairs to the device by yourself. Only have your device
repaired by an authorized service center.
• Improper maintenance can result in injuries or damage to the device.
• Refer all servicing to qualified service personnel.
• Do not stare at operating beam. The bright light may hurt your eyes.
Power Supply
Hearing Safety
Cleaning
Repairs
Caution
03
What’s included
Please do not block the air ventilation (outlet).
Attention:
Please do not look into the lens directly to avoid harm for your eyes.
1. Lens
2. Air ventilation（outlet）
3. Tripod screw hole
4. Speaker
5. AUX port
6. USB 2.0
7. HDMI 1.4
8. IR receiver
9. DC in
Adapter x 1 Travel Case x 1
Remote control x 1
Overview
Front view Rear view
Projector x 1
User manual x 1
04
When playing videos/music:
Press “ ”/“ ” button to volume up / down
Long-press “ ”/ “ ” button to fast forward / backward
Press the button once: power on
Press the button twice: power off
Press to confirm a selection or entry
Navigate menus or adjust the
selected content
Return to the previous menu
Sound off
Previous
Next
Play/Pause
Signal source
Volume up / down
Access more options during play
(available depend upon the source)
Focus Adjusting Knob
Top view
05
①Place the projector right towards the projection surface to get a
rectangle picture.
②The distance between the projector and the projection surface
determines the picture size.
③Check the projection distance and screen size on specifications part.
①Press and open the battery cover, as illustrated.
②Install two AAA batteries. Make sure that the positive and negative
ends are positioned correctly, as illustrated.
③Place the battery cover back until it clicks into place.
• Press the power button once to power on.
• Press the power button twice to power off.
Install the remote control batteries (batteries not included).
Placement
Prepare the Remote Control
Power On
Get Started
3
1.2m
40" 100"
3.2m
06
①Place the projector towards a suitable projection surface or wall,
adjust the distance for a proper size of picture.
②Scroll the [Focus Adjusting Knob] left or right until the picture
is crystal clear.
Focus
Quick Guide & Help
Select Your Language
When start the projector for the first time, you will be guided to a page to
select language, use remote control or to select your language. Then
press the right button and select "Complete" to enter the next page.
Quick Guide & Help provides some tips and help.
07
Go through the set-up process when you turn on the projector for the first time.
Use the remote control to resize the picture size from 50% to 100% without
moving the projector.
This Projector support digital keystone correction and remote four-point
keystone correction.
If the projected image is noticeably wider at one side. Go to homepage，
select [Settings] -> [Projection] -> [Vertical Correction] / [Horizontal
Correction], press left or right button on the remote control to adjust.
• Vertical / Horizontal Correction
Projection Mode
Zoom in/out
Vertical Correction
Keystone correction
Projection
Indice
Altri manuali ETOE Proiettore
