EUFY eufyCam 2 Pro Manuale utente
Anker Innovations Limited. All rights reserved. eufy Security and
eufy Security Logo are trademarks of Anker Innovations Limited,
registered in the United States and other countries. All other
trademarks are the property of their respective owners.
51005002323 V01
QUICK
START GUIDE
eufyCam 2 Pro
WIRE-FREE HD SECURITY CAMERA
EN 01
TABLE OF
CONTENTS
What's Included 02
Product Overview 03
Adding eufyCam 2 Pro 04
Mounting the Camera 05
Charging eufyCam 2 Pro 10
Notice 11
English 01
Deutsch 15
Español 25
Français 35
Italiano 45
Nederlands 55
Portuguese 65
75
02 EN EN 03
WHAT’S
INCLUDED
1
For eufyCam 2 Pro installation
eufyCam 2 Pro
(T8140)
Micro-USB
Charging Cable
Mounting
Bracket
Mounting Screws
and Anchors
2PRODUCT
OVERVIEW
eufyCam 2 Pro
6
3
4
52
1
8
7
1. Photosensitive sensor
2. Camera lens
3. Motion sensor
4. Microphone
5. LED indicator
6
3
4
52
1
8
7
6. Sync button
7. USB charging port
8. Screw hole
WHAT'S
INCLUDED
Indoor
Mount
Hook
(for Indoor Mount)
04 EN EN 05
3ADDING
Adding eufyCam 2 Pro to Your
Existing System
On eufy Security app, follow the onscreen
instructions to add your eufy devices. Choose
Add Device, then select eufyCam 2 Pro to add
it to your system.
4
Find a Good Mounting Spot
To nd a spot to mount eufyCam 2 Pro, you need
to test wireless signal strength.
①Open the eufy Security app, go to Camera
Settings > Mounting Guide.
②To test the wireless signal strength, take your
camera and phone to the location where you
want to mount the camera.
③Move the camera as close to the HomeBase 2
as possible if the wireless.
EUFYCAM 2 Pro
06 EN EN 07
Select Height and Location
Hang eufyCam 2 Pro 7-10 ft (2-3 m) above the
ground.This height maximizes the detection
range of the motion sensor of eufyCam 2 Pro.
Avoid placing eufyCam 2 Pro under direct
sunlight.
Up to 30 ft (10 m)
7-10 ft
(2 - 3 m)
Camera eld
of view Motion
Detection
Zone
Mount the camera
The camera can be mounted both indoors and
outdoors.
1. Turn the knob of the mounting bracket
clockwise to loosen and disassemble it.
2. Drill holes with a 15/64 inch (5.95mm)
drill bit, then insert the anchors into the
holes; anchors are necessary for walls that
are made out of hard materials such as
concrete, brick, or stucco.
3. Firmly screw the base of the mounting bracket
onto the wall. Fasten the ball knob of the
bracket to the base of the bracket.
08 EN EN 09
4. Tighten eufyCam 2 Pro to the mounting
bracket and adjust the viewing angle by
checking the live stream feed in the Eufy
Security app.
Tips:
For troubleshooting, check Help on the
eufy Security App.
Mount the Camera Indoors
Stick the camera directly to any at surface
made out of iron. Or you can use the indoor
mount to mount the camera:
1. Drill a hole. Use the included anchor if it’s
drywall and fasten the hook.
a
2. Hang the indoor mount on the hook.
b
3.Attach eufyCam 2 Pro to the indoor mount
and adjust the viewing angle.
c
10 EN EN 11
EUFYCAM 2 PRO
5
Charge eufyCam 2 Pro
Method 1
Method 2
5V / 2A
LED
indication
Charging
time 12 hours
Fully charged: Off
Charging: Steady blue
6 NOTICE
FCC Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Warning: Changes or modications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
(1) Reorient or relocate the receiving antenna.
(2) Increase the separation between the equipment
and receiver.
(3) Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
12 EN EN 13
(4) Consult the dealer or an experienced radio/TV
technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF
exposure requirements. The device can be used in
xed/mobile exposure condition. The min separation
distance is 20 cm.
Notice: Shielded cables
All connections to other computing devices must be
made using shielded cables to maintain compliance
with FCC regulations.
FCC ID:2AOKB-T8114
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 400 108th Ave NE Ste 400, Bellevue,WA
98004-5541
Telephone:1-800-988-7973
This product complies with the radio
interference requirements of the European
Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that
this device is in compliance with the essential
requirements and other relevant provisions of
Directive 2014/53/EU. For the declaration of
conformity, visit the Web site www.eufylife.com
Do not use the Device in the environment at
too high or too low temperature, never expose
the Device under strong sunshine or too wet
environment.
The suitable temperature for eufyCam 2 Pro and
accessories is -20°C-50°C.
When charging, please place the device in an
environment that has a normal room temperature
and good ventilation.
It is recommended to charge the device in an
environment with a temperature that ranges from
5°C~25°C.
RF exposure information: The Maximum Permissible
Exposure (MPE) level has been calculated based
on a distance of d=20 cm between the device and
the human body.To maintain compliance with RF
exposure requirement, use product that maintain a
20cm distance between the device and human body.
CAUTION RISK OF EXPLOSION IF BATTERY IS
REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDINGTO THE
INSTRUCTIONS.
Wi-Fi Operating Frequency
Range: 2412~2472MHz ; Wi-Fi Max
Output Power: 17.47 dBm
The following importer is the responsible party
(contact for EU matters only)
Importer: AnkerTechnology (UK) Ltd
Importer Address: Suite B, Fairgate House, 205
Kings Road,Tyseley, Birmingham, B11 2AA, United
Kingdom
This product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This symbol means the product must not be
discarded as household waste, and should be
delivered to an appropriate collection facility
for recycling. Proper disposal and recycling helps
protect natural resources, human health and the
environment. For more information on disposal
and recycling of this product, contact your local
municipality, disposal service, or the shop where
you bought this product.
DE 15
14 EN
IC Statement
This device complies with Industry Canada licence-
exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause undesired
operation of the device."
Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le
fonctionnement."
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme
à la norme NMB-003 du Canada.
IC RF Statement:
When using the product, maintain a distance of
20cm from the body to ensure compliance with RF
exposure requirements.
Lors de l'utilisation du produit, maintenez une
distance de 20 cm du corps an de vous conformer
aux exigences en matière d'exposition RF.
INHALTSVERZEICHNIS
Im Lieferumfang enthalten 16
Produktübersicht 17
18
Montieren der Kamera 19
Auaden der eufyCam 2 Pro 24
eufyCam 2 Pro zur Ihrem
existierenden System hinzufügen
16 DE DE 17
IM LIEFERUMFANG
ENTHALTEN
1
Für eufyCam 2 Pro-Installation
eufyCam 2 Pro
(T8140)
Mikro-USB-
Ladekabel
Montage-Halterung Befestigungsschrauben
und Dübel
2PRODUKT-
ÜBERSICHT
eufyCam 2 Pro
6
3
4
52
1
8
7
1. Lichtempndlicher Sensor
2. Kameraobjektiv
3. Bewegungssensor
4. Mikrofon
5. LED-Anzeige
6
3
4
52
1
8
7
6. SYNC-Taste
7. USB-Ladeanschluss
8. Schraubenloch
Halterung für
Innenbereich
Haken (für Montage
im Innenbereich)
Indice
Lingue:
Altri manuali EUFY Telecamera di sicurezza
