EuroFans MORENO Guida all'installazione

OWNERS INSTRUCTION

MANUAL

MORENO

INSTALLATION

OPERATION

MAINTENANCE

CAUTION

READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND

FAN OPERATION. IF UNSURE CONSULT

A QUALIFIED ELECTRICIAN

SUITABLE FOR 230V/50 CYCLE ELECTRICAL SUPPLY

Enquiries on installing your fan please call our help line on

01959-564440

technical@fantasiaceilingfans.com

106CM/42” or 91CM/36”

Safety Precautions

1. To ensure the success of the installation be sure to read the instructions and study

the diagrams thoroughly before commencing.

2. All electrical work should only be undertaken after disconnection of the power by

removing fuses or turning off the circuit breaker to ensure all pole isolation of the

electrical supply. If you are in any doubt the services of a qualified electrician should

be sought to ensure that all work is carried out in accordance with the I.E.E.

Regulations, current good practice and other national and local electrical codes.

3. Make sure that your installation situ will not allow the rotating fan blades to come into

blade tip to the wall or ceiling. Please note that the bigger this clearance is the better

the airflow from your fan will be. Ensure the blades are mounted at a minimum height

4. The fixing point for the fan must be able to support a weight of ten times that of the net

wei

support the moving weight of the fan and must not twist or work loose.

5. The fan must be earthed.

6. Do not connect the fan motor to a dimmer switch. This may give an unsatisfactory

performance (motor hum) and cause damage to the motor.

7. It is not recommended that ceiling fans and gas appliances are operated in the same

room at the same time.

8. The fan must be turned off and stopped completely before reversing the fan direction.

This will prevent any damage to the motor of the unit or controller (if installed).

9. Do not insert anything into the fan blades while the fan is operating. This will damage

the blades and upset the balance of the unit causing the unit to wobble.

10. After the fan is completely installed make sure that all connections are secure

and tight to prevent any problems.

11. osen. Check the

support connections, brackets and blade attachments twice a year to make sure they

are all secure. If they are loose tighten with a screwdriver.

Note: The important safeguards and instructions given in this manual are not meant to

cover all possible conditions and situations that may occur. It must be understood that

common sense, caution and care are factors, which cannot be built into any product.

These factors must be supplied by the persons caring for and using the unit.

For installation advice, or in the unlikely event of damaged or missing parts please ring:

HELPLINE: (01959) 564 440

Supplied Parts

One fan AC motor assembly

One hanger bracket fitted with terminal block and top rubber washers.

One set of blades

One set of blade carriers

One light kit

One screw-pack with balancing kit

One installation booklet.

Tools and Materials Required

Philips screwdriver

Blade screwdriver

Small electrical screwdriver

Electrical pliers

Step ladder

Wiring supplies as required by current electrical practice

Bulbs if a light fitting is fitted / to be fitted

In-line crimps or other suitable connectors if an extension rod in excess

of 760mm (30 inch) is to be fitted.

Before starting the assembly and installation of your fan please ensure the safety

precautions have been read and understood.

Installation Difficulties, Missing or Damaged Parts

If you have any difficulty in installing your fan/light or if you are unfortunate enough to

find that your fan have been dispatched with parts missing or damaged please contact

our help-line on 01959 564 440. We will be very pleased to provide help or forward

replacements parts to your immediately.

In any communication with us please quote model reference, colour of the unit and the

part missing /damaged.

HELPLINE

01959 564440

technical@fantasiaceilingfans.com

ASSEMBLING AND HANGING YOUR CEILING FAN

NOTE:

Before installing ensure that you have all poles disconnection of the electricity supply and that

you refer to qualified electrician to ensure that all wiring is carried out in accordance with

I.E.E. Regulations, current good practice, national and local electrical codes.

A. CLOSE TO CEILING MOUNTING

STEP 1: HANGER BARCKET AND CANOPY INSTALLATION

Secure the hanger bracket to joist with wood screws, rubber and steel washers.

Please make sure it is secured firmly. (See Fig. 1)/page 4.

Release 3 screws from upper housing

Put the canopy pass the electrical supply leads and align the screws holes on the

boss which is on the top of housing. Use the three flush mount set screws

to screw the canopy onto the fan, please make sure it is screwed firmly.

It will cause wobble or risk the fan falling down if the canopy isn't screwed or

tightened correctly. (See Fig 2)/page 4

CAUTION: Be sure that the hanging location can support load of at 70 kilos.

(see Safety Precautions)

STEP 2 : BLADE ASSEMBLY

led on to theThe blades now need to be assemb

blade carriers. Note that blades can be

installed with either surface facing down.

Carefully unwrap the blades and carriers. Align

the bracket with the holes in the blades and use

the screws and fibre washers provided to connect

them.

The fibre washer should go on top the blade

between the head of the screw and the surface

of the blade. Ensure the screws are tightened

firmly. Repeat this process for all blades.

Install the blade carrier with blade on to the

motor, using the motor screws to secure it

(provided in screw pack). Please make sure it

is tightened fully. Be careful not to bend the

blades or the carrier brackets during

installation as this may result in an imbalance

and induce wobble.

If installing more than one fan be careful not to

mix the blade sets. Each set is carefully

manufactured to be evenly balanced, mixing

would break up a balanced set and again this

could induce wobble.

STEP 3 : LIGHT KIT INSTALLING

Unscrew three screws from switch cover of light kit

Connect the push plug for light kit of ceiling fan to push plug of light kit.

Blue to Blue wire

Black to Black wire

Carefully collect all wires into switch housing of ceiling fan, then install the light

kit to switch housing using the 3 screws. Ensure the light kit is secured

firmly. Please see drawing details on page 10 Assembly light kit.

STEP 4: HANGING

Hang the motor on mounting plate with temporary support (a hook)

(See Fig. 3)/page 4.

This is an aid while making the electrical connection.

STEP 5 : WIRING (See Page 9 )

CAUTION: Carefully read the WIRING INSTRUCTIONS and DIAGRAMS

Since improper installation may result in an electric short and

void the warranty

STEP 6 : FAN HANGING

Carefully push all wiring into canopy. Remove from hanging

hook and position fan motor on hanger bracket such that attachment screws align

with keyed slots on upper side of motor housing. Secure fan to hanger bracket

with serrated washers and screws provided (See Fig. 4). Ensure a good electrical

connection by breaking lacquer finish as this forms the earth.

STEP 7 : FAN CHECKING

Turn on the electricity. Check to see that the fans forward and

reverse speeds work properly see operating instructions.

FLUSH MOUNT STYLE ASSEMBLY DIAGRAMS

Fig.1

Fig.2

Fig.3 Fig.4

JOIST OR

BEAM

CEILING

WOOD SCREWS

MOUNTING

PLATE

ROUND

STEEL

(MAYBE ATTACHED

ON THE PLATE)

B. DROP ROD STYLE INSTALLATION

STEP 1 : HANGER BRACKET INSTALLATION

Secure the hanger bracket to joist with wood screws, rubber and steel washers.

Please make sure it is secured firmly. (See Fig. 6)/page 7.

CAUTION : Be sure that the mounting location can support load of

at 70 kilos. (see Safety Precautions )

STEP 2 : DROP ROD ASSEMBLY

Remove the cotter pin and split pin from the bottom of the drop rod. If a longer

drop rod is going to be used, transfer the ball joint and the earth wire to the

longer rod.

Put the drop rod through the flared end of the canopy and pass the electrical

supply leads from the top of the motor through the drop rod until they exit at the

top of the ball joint. Always ensure the rod passes through the canopy before

the rod is connected to the fan. If an extension rod longer than 30 inches is to be

used, the cables will need to be extended in an appropriate way. (SEE FIG. 7)

Loosen the drop rod set screws on the boss, which is on top of the motor and

insert the drop rod into the drop rod boss on top of the motor casing. Turn gently

to align the holes in the boss with those in the rod. Ease the cotter pin through

the boss and the rod taking care not to pinch or damage any cables. Fix in place

by replacing the split pin.

STEP 3 : BLADE ASSEMBLY

led on to the

The blades now need to be assemb

blade carriers. Note that blades can be

installed with either surface facing down.

Carefully unwrap the blades and blade carriers.

Align the bracket with the holes in the blades and

use the screws and fibre washers provided to

connect them.

The fibre washer should go on top the blade

between the head of the screw and the surface

of the blade. Ensure the screws are tightened up

firmly. Repeat this process for all blades.

Put blade carrier with blade on the motor. Using

motor screws to screw it (provided in screws

pack). Please make sure it is tight enough. Be

careful not to bend the blades or the carrier

brackets during installation as this may result in

an imbalance and induce wobble.

If installing more than one fan be careful not to

mix the blade sets. Each set is carefully

manufactured to be evenly balanced, mixing

would break up a balanced set and again this

could induce wobble.

STEP 5: HANGING

Hang the fan on to hanging bracket

(See Fig. 8)/page 6. This is an aid in making the electrical connection.

STEP 6 : WIRING (See Page 9)

CAUTION : Carefully read the WIRING INSTRUCTIONS and DIAGRAMS since

improper installation may result in an electric short and void the warranty

STEP 7 : AFTER FAN WIRING

Carefully push all wiring into canopy, then, put the canopy to hanger bracket and

use the attachment screws align with keyed slots on upper side of canopy with

serrated washers and screws provided. Ensure a good electrical connection by

breaking lacquer finish as this forms the earth. (See Fig. 8)

STEP

: FAN CHECKING

Turn on the electricity. Check to see that the fans forward and reverse speeds

work properly see operating instructions.

STEP 4 : LIGHT KIT INSTALLING

Unscrew three screws from switch cover of light kit

Connect the push plug for light kit of ceiling fan to push plug of light kit.

Blue to Blue wire

Black to Black wire

Carefully collect all wires into switch housing of ceiling fan, then install the light

kit to switch housing, using the three screws. Ensure the light kit is secured

firmly. Please see drawing details on page 10 Assembly Light kit.

DROP ROD STYLE ASSEMBLY DIAGRAMS

Fig.5 Fig.6

Fig.7 Fig.8

WIRING INSTRUCTIONS

NOTE:

Before installation ensure that you have all pole disconnection of the electricity supply and

that you refer to a qualified electrician to ensure that all wiring is carried out in accordance

with I.E.E. Regulations current goods practice national and local electrical codes.

Carefully read the wiring instructions and diagrams since improper installation may result

in an electrical short and void the warranty.

In most cases connect the fan motor BROWN wire to the supply wire coloured RED or

BROWN, connect the fan motor neutral BLUE wire to the neutral supply normally coloured

BLUE or BLACK, connect the mounting plate GREEN or GREEN/YELLOW earth wires to

the earth supply. SEE FIG. 9

When the light kit is attached, connect the ORANGE light wire to the supply live wire,

normally coloured RED or BROWN. If light to be independently operated from a wall

switch a separate live supply is required. SEE FIG.9

If fan is controlled independently from a wall switch. SEE FIG. 11

If a separate wall control is to be used for both fan and light please see wiring diagram

supplied with control or SEE FIG. 11.

Check to see that all your connections are tight and that no bare wires are visible of

touchable at any of the wire connectors. Except for the earth wire. Gently tuck all of the

completed wiring carefully into the canopy. If required, cut the wiring to suit.

CAUTION: THIS APPLIANCE MUST BE EARTHED. IMPORTANT: Do not connect the

motor supply cable to a dimmer switch. If a wall mounted control for the

fan is required then we recommend you contact our help-line.

BLACK BLUE

BLUE

BLACK

BLUE

BLACK

FROM CEILING

OR BEAN

BROWN

BLUB

EARTHING WIRE

BLUE(NEUTRAL)

EARTH WIRE

LOCATION

230V LIVE

LIGHT SWITCH

LIGHT LEAD

ORANGE

FAN LEAD

BROWN

FIG.8 FIG.10

WALL

EARTH WIRE

FROM CEILING

OR BEAN

(NEUT RAL)

BLUE

EARTHING WIRE

BLUE(NEUT RAL)

EARTHING WIRE

OR BEAN

FROM CEILING

EARTH WIRE

230V LIVE

FAN CONTROL

SWTICH

LIGHT

SWTICH

LIGHT LEAD

ORANGE

FAN LEAD

BROWN

LIGHT LEAD

ORANGE

FAN LEAD

BROWN

FIG.11

FIG.9

FOR CONTROL OF FAN OR FAN AND

FOR CONTROL OF LIGHT ONLY FROM WALL SWITCH FOR CONTROL OF FAN AND LIGHT FROM WALL

FOR CONTROL OF FAN FROM

OPTIONAL LIGHT FROM FAN

BROWN FAN

LEAD

ORANGE

LIGHT LEAD

BLACK BLUE

BLUE

BLACK BLUE

BLACK

Indice

Altri manuali EuroFans Fan

EuroFans

EuroFans MONTANA Guida all'installazione

EuroFans

EuroFans Atom Guida all'installazione

EuroFans

EuroFans Neptune Guida all'installazione

EuroFans

EuroFans Atlanta Guida all'installazione

Manuali Fan popolari di altre marche

ELTA FANS

ELTA FANS H03VV-F Manuale utente

Hunter

Hunter 20714 Manuale di istruzioni

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuale utente

Hunter

Hunter Caraway Manuale di istruzioni

Panasonic

Panasonic FV-15NLFS1 Manuale utente

Kompernass

Kompernass KH 1150 Manuale utente

VES

VES FALA100/12V/TR Manuale utente

Vertiv

Vertiv Liebert DCD Manuale utente

Westinghouse

Westinghouse GFP Series Manuale utente

Venmar

Venmar KUBIX HRV PLUS Series Manuale utente

Maico

Maico ECR 31 Manuale utente

Sonnenkonig

Sonnenkonig Dinky Manuale utente

S&P

S&P ECOWATT HXBR Manuale utente

Wider

Wider IMP03369BH Manuale utente

Panasonic

Panasonic F-60DHN Manuale utente

Hinkley

Hinkley HIGHLAND Manuale utente

Broan

Broan 766BN Manuale utente

Premium

Premium PFS16022 Istruzioni per il montaggio