EUTECH INSTRUMENTS ALPHA PH 1000 PHORP CONTROLLERTRANSMITTER Manuale utente

Tech nolo

ade

Instruction Manual

alpha-pH1000

pH and ORP Controller/Transmitter

68X216801 rev 1.1

07/02

Instruction Manual alpha-pH 1000

Preface

This manual serves to explain the use of the αlpha-pH1000 series pH/ORP controller/transmitter. The

manual functions in two ways, firstly as a step by step guide to help the user operate the instrument.

Secondly, it serves as a handy reference guide. This instruction manual is written to cover as many

anticipated applications of the αlpha-pH1000 pH/ORP controller/transmitter. If you have doubts in the use

of the instrument, please do not hesitate to contact the nearest Eutech Instruments’ Authorised Distributor.

The information presented in this manual is subject to change without notice as improvements are made,

and does not represent a commitment on part of Eutech Instruments Pte Ltd.

Eutech Instruments cannot accept any responsibility for damage or malfunction of the unit due to improper

use of the instrument.

Instruction Manual alpha-pH 1000

Safety Information

The Eutech Controller/ Transmitter shall be installed and operated only in the manner specified in the

Instruction manual. Only skilled, trained or authorized person should carry out installation, setup and operation

of the instrument.

Before powering up the unit, make sure that power source it is connected to, is as specified in the top label.

Failure to do so may result in a permanent damage to the unit.

The unit has live and exposed parts inside. If it has to be opened, make sure that the power to the unit is off

and disconnected.

The unit is Fuse protected. In the event the fuse has to be replaced, use only those as specified in the manual.

Instruction Manual alpha-pH 1000

TABLE OF CONTENTS

1INTRODUCTION 5

1.1 Description of Unit 5

1.2 Applications 5

2ASSEMBLY AND INSTALLATION 6

2.1 Measurement and Control System 6

2.2 Unit Dimensions 6

3ELECTRICAL CONNECTION 7

3.1 Connection Diagram 7

3.2 Back Panel 9

4OVERVIEW 10

4.1 Keypad and Display 10

4.2 Function Groups 11

4.3 Control Concept 12

5MEASUREMENT 13

5.1 Display in Measurement mode 13

5.2 Security Codes 13

6CALIBRATION MODE 15

6.1 pH Calibration 15

6.2 ORP – mV Calibration 16

6.3 ORP -% Calibration 17

7ADVANCED SET-UP MODE 18

7.1 Electrode Offset (OFS) sub-function 18

7.2 Setting temperature (Set oC) sub-function 18

7.3 Control Relay A/Control Relay B (SP1/SP2) sub-function 20

7.4 Controller (Cntr) sub-function 22

7.5 Current Output (rng) sub-function 24

7.6 Configuration (ConF) sub-function 25

7.7 Calibration (CAL) sub-function 28

8AUTO/MANUAL MODE 29

8.1 Auto mode (mode after switch-on) 29

8.2 Manual mode 29

9TECHNICAL SPECIFICATIONS 30

10 ACCESSORIES 32

11 GENERAL INFORMATION 33

11.1 Warranty 33

11.2 Packaging 33

11.3 Return of Goods 33

11.4 Guidelines for Returning Unit for Repair 33

12 APPENDICES 34

12.1 Appendix 1 34

12.2 Appendix 2 35

12.3 Appendix 3 36

12.4 Appendix 4 37

Instruction Manual alpha-pH 1000

1 INTRODUCTION

1.1 Description of Unit

Thank you for purchasing Eutech’s ¼ DIN alpha-1000 series pH/ORP process controllers. This unit is used

for measuring either pH or ORP parameter one at a time, and the operational mode is switchable from the

menu. You can use this unit to measure pH or ORP with proportional or limit control. This controller has

many user-friendly and safety features which include:

•Menu-driven program that simplifies set-up

•Built-in memory backup to ensure that calibration and other information are not erased if power

supply fails

•Push-button two-point calibration and electrode offset adjustment from the keypad

•Automatic temperature compensation (ATC)

•Manual temperature compensation setting without the ATC probe, with independent setting for

calibration and process temperature

•0 to 2000 second time delay adjustment on all relays – minimise false alarms

•Separately adjustable high and low set point hysteresis (dead bands) prevent chattering of relays

around the set points

•Asymmetrical/symmetrical input for pH/ORP mode of operation

•Three control modes: limit, proportional pulse length or proportional pulse frequency

•Large dual display LCD for easy reading with clear multiple annunciators, alarm status, operational

and error messages

•Two switching contacts as set-point triggering relays and an alarm output relay

•A third relay that can be set up to perform either Alarm or Wash function

•When set to work as Alarm relay, alerts you to set points exceeded for a set-point limits for certain

time and if the Pt100/Pt1000 wires are broken or disconnected during the ATC function

•Programmable duration and frequency in the Wash mode

•Hold function freezes output current (0/4...20mA) and releases control relays

•LED indicators signal control activities to monitor controller status from a distance

•Protection against electromagnetic interference - galvanically isolated 0/4..20mA output provides

safety for data logging and control purposes

•Choice of 7 buffers from USA or NIST standards

1.2 Applications

Use this controller in panel mounted enclosures for applications such as water treatment and monitoring,

galvanic-decontamination, chemical processing food processing, clean or waste water control and

neutralisation process.

Instruction Manual alpha-pH 1000

2 ASSEMBLY AND INSTALLATION

2.1 Measurement and Control System

A typical measurement system consists of:

•a pH/ORP process controller

•a pH/ORP combination electrode with integrated or separate temperature sensor Pt 100/1000,

•an immersion, flow or process assembly with or without a potential matching pin (PMP)

•a final control element such as pump or valve

•a recorder and

•an appropriate pH or ORP measurement cable.

2.2 Unit Dimensions

The field-tested control panel housing is 96 x 96 mm; with protection class IP 54 (front).

max. 175

max. 45

Mounting Cut-Out

Flat

asket

(

)

(To be Inserted By Customer)

Note: The Taped Corners Have to Be On Top

92 + 0.5

Power Mains

(220/110 VAC)

Flow Assembly

Measurement Cable

Process Assembly

with El

Chart Recorde

pH Controller

ALARM

REL A

REL B

ESC

CAL

ENTER

REL A

AUTO

REL B

MANU

7.02

25.0

ATC

MEAS

alpha-pH1000

Instruction Manual alpha-pH 1000

3 ELECTRICAL CONNECTION

3.1 Connection Diagram

Caution: Ensure electrical mains is disconnected before proceeding.

Signal OutputHold Input

Relay B

Relay A

Power Mains

Alarm/Wash

PEAC: NL

78 9 10 11 12 13 14 15 17

15 16

* ) indicated contact positions are for currentless conditions

Pt 100

Potential Matching Pin (PMP) Signal Input pH

ORP

PE/S

18 19 20 21 22

S/S/

BNC

Instruction Manual alpha-pH 1000

Symmetrical high-impedance

connections

Asymmetrical connections

Measuring Cable

pH Combination

Electrode

Te m p . pH

BNC

0/PA

PE NLS

22 21

320 19 18

Potential

Matching Pin (PM)

Instruction Manual alpha-pH 1000

3.2 Back Panel

Caution: Ensure electrical mains is disconnected before proceeding.

The back panel consists of two connectors. The first connector is the 17-way PCB edge connector and the

other is the 5-way connector.

Connection for the 17-way screw terminals (from left to right):

1. AC mains live wire 10. Alarm/Wash relay working position (NO)

2. AC mains neutral wire 11. Alarm/Wash relay common

3. AC mains protective earth wire 12. Alarm/Wash relay resting position (NC)

4. Low set relay resting position (NC) 13. Hold function switch terminal 1

5. Low set relay common 14. Hold function switch terminal 2

6. Low set relay working position (NO) 15. No connection

7. High set relay resting position (NC) 16. 0/4 - 20 mA for -ve connection

8. High set relay common 17. 0/4 - 20 mA for +ve connection

9. High set relay working position (NO)

Connections for the 5-way screw terminals:

18. Pt100/Pt1000 lead 1 terminal

19. Pt100/Pt1000 sense lead terminal

20. Pt100/Pt1000 lead 2 terminal

Note: If using a two-wire RTD, short terminal 19 to terminal 18.

Pt 100/Pt 1000 is selectable via an internal jumper. Factory default is Pt100. See Appendix 1 for

directions on switching the RTD type.

21. pH/ORP (potential matching pin)

21. pH/ORP (shield)

Pt100

RELAY A

100mA (F)

FUSE 250VAC

HOLD

LARM / WASHRELAY B

Pt1000

PAL

IMPORTANT: The Alarm relay functions as an “Active Low” device i.e. it switches OFF under Alarm

condition. Therefore the Alarm display device should be connected to the ‘NC’ contacts of the relay (11

and 12). In the Wash mode, the relay works on a positive mode. Therefore, the Wash device should be

connected to the contacts 10 and 11.

Instruction Manual alpha-pH 1000

4 OVERVIEW

4.1 Keypad and Display

4.1.1 Keypad

CAL

•Perform rapid 2-point calibration

•Allows entry to Set up mode

•Select individual functions within the function group of Set up mode

•Store input data in the Set up mode

•Start calibration in the calibration mode

•Select various function groups in the Set up mode.

•Set parameters and numerical values in sub functions of Set up mode

If pressed continuously, the setting speed increases

•Control the relays in the MANUAL function

•Return to the Measurement mode when both keys are pressed together

•Switch between AUTO and MANUAL relay operation using a code

•Display limit set-point values for the switch contacts in AUTO relay operation mode

•Switch between RELAY A and RELAY B in MANUAL relay operation mode

4.1.2 Display

The LCD display features two numerical displays that show status messages and measured values for easy,

quick reference. The display provides short-text information for setting parameters and configuration.

7.00

25.0 ATC

SETUP

HOLD

CAL

MEAS CON

READY pH

ERR oC

•MEAS: Measurement mode

•SETUP: Set-up mode of function groups

•CAL: Calibration mode of pH/ORP and temperature

•READY: Comes on after a successful calibration

•HOLD: Relay position and current output are frozen

•ATC: Comes on in the ATC mode. Disappears in the

Manual temperature Compensation mode.

“ATC” flashes if the temperature probe is faulty in its ATC

mode

•ERR: Error or alarm indicator

•Display for RELAY A/B. Green LED indicates measured value within limit while

RED LED indicates measured value outside limit.

•Alarm display if limit value overshoot or the ATC probe fails; with ERR annunciator

appears on the display. Wash display if cleaning cycle is on.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali EUTECH INSTRUMENTS Trasmettitore

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS alpha-pH1000 Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA PH 500 - REV 6 Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA PH 800 PHORP CONTROLLERTRANSMITTER Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA PH 500 PHORP 2-WIRE TRANSMITTER (REVISION... Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA TDS 200 TOTAL DISSOLVED SOLIDS... Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS 2-WIRE DISSOLVED OXYGEN TRANSMITTER Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA CON 500 2-WIRE TRANSMITTER Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA PH 100 PHORP CONTROLLERTRANSMITTER Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS alpha-pH 2000D Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA PH 200 - REV 4 Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA RES 1000 RESISTIVITY... Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS 2-WIRE TEMPERATURE TRANSMITTER Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA TDS 190 18 DIN TOTAL DISSOLVED SOLIDS... Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS 2-WIRE CONDUCTIVITY TRANSMITTER Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA PH1000 PHORP CONTROLLERTRANSMITTER Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA COND 200 - REV 3 Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA PH 500 PHORP 2-WIRE TRANSMITTER (REVISION... Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS apha-CON500 Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA PH 500 - REV 6 Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA CON 190 18 DIN CONDUCTIVITY... Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS 2-WIRE PHORP TRANSMITTER Manuale utente

EUTECH INSTRUMENTS

EUTECH INSTRUMENTS ALPHA PH 200 PHORP CONTROLLERTRANSMITTER Manuale utente

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente