Event Lighting STORM Manuale utente
STORM
12W LED RGBW Rotating Multi Beam Effect Light
USER MANUAL
For your safety, please read this user manual carefully before use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version 1.0 (revised 5 November 2020)
www.event-lighting.com.au
1
Safety Instructions
Warning
• Do not open this device, there are no user serviceable parts inside. Risk of electric
shock.
• Do not look directly at the light source from close range.
• Avoid contact with the unit during operation, as the housing may become hot. Allow the
fixture to cool for at least 15 minutes after turning off before touching.
• Install this device in a location with adequate ventilation, at least 50cm from adjacent
surfaces.
• Do not operate this device, or connect this device to power, within 50cm of any
flammable material.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors where excessive dust, heat, water, or humidity may
affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• Do not operate this device at temperatures higher than 40°C (104°F).
• Only connect this device to a grounded and protected circuit.
• Only use the hanging bracket to carry this device.
• Stop using this device immediately if a serious operating problem becomes apparent.
Power Input and Power Linking
This device has an auto switching power supply work with input voltage range of 100-240V AC,
50/60Hz. Link up to a maximum of 8A. Do NOT exceed this numbe.r
Product Installation
STORM can be mounted in many orientations, provided each individual device is secured by the
use of the correct mounting bracket. Use a safety chain when mounting STORM overhead.
Fuse Replacement
If the fine-wire fuse of the device fuses, replace the fuse with one of the same type of rating.
Before replacing the fuse, unplug the device from the power source.
Fuse Replacement Steps
1. Unscrew the fuse holder located on the rear panel from the housing.
2. Remove the old fuse from the holder.
3. Install the new fuse into the holder.
4. Place the fuse holder back into the housing and secure tightly.
www.event-lighting.com.au
2
Dimensions
Control Panel
Buttons and Indicators
(1) LED Display
(2) DMX signal LED indicator (On/Off)
(3) Slave Mode LED indicator (On/Off)
(4) Master Mode LED indicator (On/Off)
(5) Sound Active Mode LED indicator (On/Off)
(6) MENU – Select an operation mode or return to
previous screen.
(7) UP – Increase parameters.
(8) DOWN – Decrease parameters.
(9) ENTER – Confirm the selected function.
Input and Output
(10) Fuse (T3A M205)
(11) IEC Power In
(12) IEC Power Out
(13) DMX In
(14) DMX Out
www.event-lighting.com.au
3
Menu
Press the MENU button to select an operation mode or return to the previous menu. Use UP and
DOWN to navigate the menu. Press ENTER to change or activate menu options.
DMX Chart
Channel
Value
Function when Channel 1’s
value is 59-255
Function when Channel 1’s value
is 0-58
1
000 - 058
Switch on colour dimmer DMX
mode
059 - 078
Auto show 1
079 - 098
Auto show 2
099 - 118
Auto show 3
119 - 138
Auto show 4
139 - 158
Auto show 5
159 - 178
Auto show 6
179 - 198
Auto show 7
199 - 227
Sound active show 1
228 - 255
Sound active show 2
2
000 - 255
Program speed adjustment for
auto show 5, 6 & 7
Master dimmer
3
000 - 255
Strobe speed adjustment
strobe speed adjustment
4
000 - 255
Motor speed adjustment
Red 0% ~ 100%
5
000 - 255
Green 0% ~ 100%
6
000 - 255
Blue 0% ~ 100%
7
000 - 255
White 0% ~ 100%
Select DMX Address
Master Mode
Slave Mode
First digit: Motor Speed. Second digit: Program
Program Speed adjustment for Auto Program 5, 6, 7
Strobe Speed
Sound Active Program 1 or 2
Red LED Brightness
Green LED Brightness
Blue LED Brightness
White LED Brightness
Motor Speed
Normal Display
Inverted Display
Software Version
www.event-lighting.com.au
4
8
000 - 009
The motor stops
010 - 128
Counter clockwise rotation speed
adjustment (slow to fast)
129 - 137
The motor stops
138 - 225
Clockwise rotation speed
adjustment (slow to fast)
Technical Specifications
Photometrics
• Light Source: 1x 12W CREE RGBW 4-in-1 LED
• Coverage angle: 85°
• LED Lifespan: 50,000 hours.
Power
• Input Voltage: 100~240V AC, 50/60 Hz.
• Power Consumption: 72W.
• Connection: IEC in/out.
Control
• Protocol: DMX512.
• Operation modes: DMX, auto, manual, sound active, master/slave
• DMX Channels: 8
• Interface: 3-pin DMX in/out.
• Display: LED Display with 4-button control.
Housing
• Finishing: Matte Black.
• Net Weight: 3.15kg
• Dimensions: 168x309x314 mm.
Warranty
Please refer to your local dealer or contact Event Lighting.
Indice
Altri manuali Event Lighting Attrezzatura per DJ
Event Lighting
Event Lighting PRO PAR PAR12X8L Manuale utente
Event Lighting
Event Lighting PARRGBW12x8 Manuale utente
Event Lighting
Event Lighting STROBEXRGB Manuale utente
Event Lighting
Event Lighting SToRM Manuale utente
Event Lighting
Event Lighting PIXBAR12x3 Manuale utente
Event Lighting
Event Lighting DERBY3 Manuale utente
Event Lighting
Event Lighting CO2RGB Manuale utente
Event Lighting
Event Lighting M7W40RGBW Manuale utente
Event Lighting
Event Lighting SURF640 Manuale utente
Event Lighting
Event Lighting NITROBALL2 Manuale utente
Event Lighting
Event Lighting F100WWMZ Manuale utente
Event Lighting
Event Lighting M1S190W Manuale utente
Event Lighting
Event Lighting M19W15RGBW Manuale utente
Event Lighting
Event Lighting KONTROL36 Manuale utente
Event Lighting
Event Lighting ENFORCER580 Manuale utente
Event Lighting
Event Lighting PRO PAR PAR6X12OB Manuale utente
Event Lighting
Event Lighting Fresnel Manuale utente
Event Lighting
Event Lighting Fresnel Manuale utente
Event Lighting
Event Lighting PAR19X12L Manuale utente
Event Lighting
Event Lighting DARKSTAR2 Manuale utente
