EVGA CPU Closed Loop Water Cooling Kit Manuale utente

Installation Guide

CPU Closed Loop Water Cooling Kit

The following instructions and pictures are provided to assist your installation of the EVGA CPU Closed

Loop Water Cooling Kit to Intel LGA20XX / 1366 / 115X and AMD FM1 / 2, AM2 / 3 / 4 motherboards.

Please be careful when installing the cooling kit; there several very small fasteners that can be stropped if

you are not careful. Before you begin, please verify the contents of the box to ensure that the following

items present:

If you are an Intel LGA115X or 1366 user, please put Part G on the back of motherboard. Side standoffs to

line up with cooler mounting holes in your motherboard. Please skip this step for LGA20XX and AMD

motherboards; backplates are not used for LGA20XX sockets and AMD backplates are supplied with the

motherboard.

(A) Intel LGA20XX

(2011, 2011-v3, 2066)

(M4 thread)

(B) Intel LGA115X / 1366

(1150, 1151, 1155, 1156, 1366)

(M3 thread)

(G) Intel LGA115X / 1366

(G)

FM2 (UNC 6-32 thread)

(H) Screw Nuts (M3 thread)

(D) AM4(UNC 6-32 thread)

a. Screw standoff base

into backplare. B C or D

b. Place retention ring

over standoff top.E or F

c. Screw retention ring

in place using screw nuts. H

(E) Intel LGA115X / 1366 /

20XX Retention Ring

(I) USB Cable

(F) AMD AM2 /AM3 / AM4

FM1 / FM2

Intel Backplate Installation

Next, screw the standoff into the backplate of the motherboard.

For LGA115X and LGA1366 sockets, please use the M3 thread

(Part B) to screw standoff into the baseplate. LGA20XX users

should use M4 thread (Part A) to screw standoff into the threaded

mounting holes at the corners of the socket’s retention clamps.

Use the UNC 6-32 threads (Part C & Part D) for the AMD platform.

Intel LGA115X

Intel LGA1366

Prepare AM4 standoffs, screws and retention ring. Replace the default Intel retention ring by twisting

counter-clockwise, remove the ring from the pump, then replace the ring with the AMD retention ring and

secure the ring by twisting clockwise.

AMD AM4 Installation

Make sure the correct retention ring is installed on the pump /

cooler, and then install the unit onto the standoffs. We included an

Intel and AMD retention ring in the package, with the Intel ring

preinstalled. To change the retention ring, turn the ring

counter-clockwise and remove the ring from the pump.

Secure the retention ring using screw nuts. Please follow the

tightening order; this helps to prevent CPU and / or socket

damage.

Remove plastic bracket on MB. Install part (D) standoff screws on the four posts.

Install the pump onto the standoffs. Secure the retention ring using screw nuts. Please follow the tightening

order; this helps to prevent CPU and / or socket damage.

etention ring is installed on the pump /

e included an

etention ring in the package, with the Intel ring

(H) Screw Nuts (M3 thread)(D) AM4(UNC 6-32thread)(F) AMD AM2 / AM3 / AM4

FM1 / FM2

om the pump, then

eplace the ring with the AMD

(F)

AM3

AM4

FM1 / FM2

Install radiator and fan (intake provides the best performance).

Connect fan and pump to the motherboard's 3- or 4- pin fan

headers; please check your motherboard's manual forthe

locationof itsfan headers, as connecting this to an incorrect

jack canpotentially cause irreparable damage to components.

It is recommended to enter your motherboard BIOS and set

the fan header connected to the CLC to 100%.

Otherwise you may get a WB not detected error in your OS.

Intel and AMD steps after installing the pump / CPU WB

Install the USBcable to enable PWM-tuning via software.

Connect the cable from the CPU pump to the USB 2.0 front

panel header on the motherboard.

The CPU Water Block software can be downloaded at the link

below:

http://www.evga.com/support/download/

EVGA CPU Closed Loop Water Cooling Kit is an AIO (All-In-One) cooling system. With AIO Water Cooling

Systems, you do not need to add any coolant, and the system is completely self-contained. All EVGA CPU

Closed Loop Water Cooling Kits are leak tested at the factory, and are ready to install when received.

Important Information

Your EVGA CPU Closed Loop WaterCooling Kit comes with a 5 (five) year warranty. Refer to your motherboard’s

warranty informationbefore installing the EVGA CPU Closed Loop Water Cooling Kit. Should you damage

your motherboard during the installation process,EVGA will not be held liable forthe physical damage of

your EVGA CPU Closed Loop Water Cooling Kit, case, motherboard or any associated hardware when damage

is caused by improper installation.

E009-00-000276

Warranty for the EVGA CPU Closed Loop Water Cooling Kit

Indice

Altri manuali EVGA Hardware per computer

EVGA

EVGA CLX Series Manuale utente

EVGA

EVGA Superclock Manuale utente

EVGA

EVGA inDtube Manuale utente

EVGA

EVGA 100-EV-EB01 Manuale utente

EVGA

EVGA Geforce GTX TITAN X Hybrid Manuale utente

EVGA

EVGA GeForce RTX 2070 XC Gaming Manuale utente

EVGA

EVGA UV Plus+ Manuale utente

EVGA

EVGA Z790 DARK K|NGP|N Manuale utente

EVGA

EVGA PCoIP Manuale utente

EVGA

EVGA GeForce GTX 650 Ti BOOST Manuale utente

EVGA

EVGA 141-BL-E759 Manuale utente

EVGA

EVGA UV Plus+ 39 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente