Evikon E2615-NO2 Manuale utente

Nitrogen Dioxide Transmitter

E2615-NO2

User Manual

E2615-NO2Rev 24.08.2022

Table of contents

Nitrogen Dioxide 4

Speciﬁcations 5

Product description 6

Safety requirements 6

Operating conditions 6

Installation guidelines 6

Mounting dimensions 8

Electrical connections 9

Operation 10

Maintenance 10

Calibration 10

Delivery set 11

Order code for E2615-NO2 options 11

Warranty 12

Manufacturer contacts 12

E2615-NO2Rev 24.08.2022

Nitrogen Dioxide

A Colorless toxic gas, relatively insoluble in water. When exposed to oxygen (including air),

nitric oxide is converted into nitrogen dioxide.

Chemical formula

NO2

Molar weight

Relative gas density (to air)

1.59

Conversion

1 ppm = 1.88 mg/m3

Boiling point

21.2 °C

Flammability

Powerful oxidize, can cause many organic substances

(wood, paper, oil, etc) to ignite.

Irritates the skin, eyes, and respiratory tract. Exposure to

levels above 100 ppm can cause death due to

asphyxiation from ﬂuid in the lungs. There are often no

symptoms at the time of exposure other than a

transient cough, fatigue, or nausea, but over hours

inﬂammation in the lungs causes edema.

Odor

Characteristic pungent odor

Odor threshold

0.1 to 0.4 ppm

Hazards

Irritates the respiratory tract and eyes, at high

concentrations may cause lung edema and death.

Exposure limits

(NIOSH)

ST REL

1.88 mg/m3/ 1 ppm

IDLH

37.6 mg/m3/20 ppm

Conversion of ppm to mg/m3is calculated for 25°C and 1 atm.

E2615-NO2Rev 24.08.2022

Speciﬁcations

Sensor type

Electrochemical cell

Sampling method

Diffusion

Detection range

0-30 ppm

Max. overload

150 ppm

Response time T90

≤ 25 s

Sensor lifetime

≥ 2 years

Calibration interval

6 months

Sensitivity drift

< ± 20% in 5 years

Power supply

24 VDC ± 20%

Power consumption

< 1 W

Analog outputs

4-20 mA / 0-10 V, user settable

Outdoor enclosure

Grey ABS plastic,

wall mount, protection class IP65

Indoor enclosure

White, ivory, or black ABS plastic,

wall mount, protection class IP20

Dimensions

IP65 H70 × W80 × D36 mm

IP20 H71 × W71 × D27 mm

CE marking

According to 2014/30/EU and 2014/35/EU , EN 50491-4-1:2012

EN61000-6-3:2007, EN 61326-1:2013(EMC, emissions)

EN 61000-6-1:2019, EN 61000-6-2:2019(EMC, Immunity)

EN 60079-29-1:2016, EN 60079-29-2:2015 and EN 60079-29-3:2014

Operating conditions

-20...+50 °C

15...90 %RH,

pressure 0,9...1,1 atm

Explosion safe indoor areas

Avoid strong mechanical shock, vibrations, or EMI

E2615-NO2Rev 24.08.2022

Product description

E2615 series gas transmitters are easy-to-install and easy-to-use instruments. The devices

utilize novel fully calibrated gas sensors with excellent repeatability, stability, and long

lifetime.

E2615 series provides analog output with user-selectable signal type, 4-20 mA or 0-10 V.

The version of your transmitter is marked on the package. If the symbol

⚠

is marked on

the equipment, consult the documentation for further information.

Safety requirements

Misuse will impair the protection of the product. Always adhere to the safety provisions

applicable in the country of use.

Do not perform any maintenance operation with the power on. Do not let water or foreign

objects inside the device.

Removal of the PCB from the enclosure voids the warranty. Do not touch the electronic

components directly, as they are sensitive to static electricity.

Connection diagrams can be found in the electrical connections section. The device might

not perform correctly or be damaged if the wrong power supply is connected.

External circuits connected to the equipment should have suﬃcient insulation rating

according to the environmental conditions and equipment power.

A disconnecting device that is marked as such and easily accessible should be included in

the installation of this product.

Operating conditions

The device should be used both in a non-hazardous area and in a basic electromagnetic

environment, where the latter is deﬁned in EN 61326-1. Avoid strong mechanical shock and

vibrations. Avoid corrosive atmosphere and areas highly contaminated with dust, oil mist,

etc. Keep the instrument away from direct sunlight. A sudden temperature or humidity

change might affect the sensitivity of the sensor.

E2615-NO2Rev 24.08.2022

Installation guidelines

Before proceeding with the installation it is mandatory to read the Safety requirements

section and make sure to comply with all listed instructions. Installation standards EN

60079-29-2 and EN 45544-4 are also recommended for further instructions and related

information about the installation. During the installation of the transmitter the following

points must be considered:

●Application (the instrument is intended for air quality or leakage control.)

●Properties of the space under investigation (room geometry, direction, and

velocity of airﬂows, etc.),

●Nitrogen dioxide is ca. 1.6 times heavier than air. The location of the sensor is

determined by operating conditions. Thus, in the underground parking, the NO2

rises to the ceiling with hot exhaustion gases, so the sensor should be located at

1.2...1.5 m from the ﬂoor in order to detect potentially dangerous concentrations

more quickly.

●The device should be accessible for maintenance / calibration.

The aforementioned conditions above will affect the coverage area of the device. However,

the coverage area for a transmitter is usually between 2.5 to 5 meters radius.

For early leakage detection, install the transmitter as close as possible to the potential

leakage sources (ﬂanges, valves, pressure reducers, pumps, etc.), taking into consideration

other points listed above.

For general area monitoring without deﬁnite leakage sources, the transmitters should be

distributed evenly in the room.

For personal safety control, the transmitters are installed in the breathing zone (at the

height of the head of people or animals). The recommended sensor position is vertical,

pointing downwards.

For installing the IP65 device, attach the device to the wall using provided screws through

the key slots on both sides of the device. For installing the IP20 device, detach the base of

the enclosure by gently pulling along four guiding pins and attach the base to the wall with

two screws.

E2615-NO2Rev 24.08.2022

Mounting dimensions

The IP65 instrument sensor is equipped with a hydrophobic microporous PTFE ﬁlter to

protect the sensor from dust, dirt, and water drops.

NOTE! Never stab or press the ﬁlter near its center where the sensor is located since this

may damage the sensor. Do not remove the ﬁlter as it may cause the device to show

incorrect values.

E2615-NO2Rev 24.08.2022

Electrical connections

The terminals on the E2615 series devices are suitable for a wide range of wires with a

cross-section of 0.2...1.5 mm2. We recommend to strip the wire end by 8...9 mm and use

wire end sleeves.

To connect the wire, loosen the screw, insert the wire end into the terminal hole and tighten

the screw.

The analog output can be changed between 4-20 mA and 0-10 V type using jumper on the

transmitter’s PCB.

E2615-NO2Rev 24.08.2022

Operation

Turn on the power. The instrument warm-up time takes about 1 minute after switching on

and the ﬁnal sensor stabilization time to maximum accuracy takes about 30 minutes.

Make sure that the transmitter is properly mounted and the external devices connected.

Place the lid back and ﬁx it with the screws. The device is ready to use.

Maintenance

Do not perform any maintenance operation with the power on.

Clean the device with a soft damp cloth. Do not use any abrasive cleaning agents. Do not

immerse the device in water or any cleaning media.

Calibration

E2615-NO2transmitters have been calibrated by the Manufacturer with standard gas

mixtures before delivery. Provided that the sensor is used under moderate conditions, ﬁeld

recalibration is recommended every 6 months. Please contact your dealer for more

information.

E2615-NO2Rev 24.08.2022

Delivery set

●Transmitter E2615

●Mounting accessories:

○2 screws with plastic dowels

Order code for E2615-NO2options

E2615 options

Order code

IP20 enclosure

E2615-NO2-IP20

IP65 enclosure

E2615-NO2-IP65

Indice

Altri manuali Evikon Trasmettitore

Evikon

Evikon E2615-LEL Manuale utente

Evikon

Evikon PluraSens E2658-O3 Manuale utente

Evikon

Evikon PluraSens E2670-NO2 Manuale utente

Evikon

Evikon PluraSens E2618-O2-L Manuale utente

Evikon

Evikon PluraSens E2648-NO2 Manuale utente

Evikon

Evikon E2618-NH3 Manuale utente

Evikon

Evikon PluraSens E2658-ETO Manuale utente

Evikon

Evikon PluraSens E2660-CO-NO Manuale utente

Evikon

Evikon PluraSens E2218 Manuale utente

Evikon

Evikon PluraSens E2608-ETO Manuale utente

Evikon

Evikon E2638-H2S Manuale utente

Evikon

Evikon PluraSens E2618 Series Manuale utente

Evikon

Evikon PluraSens E2670-O2 Manuale utente

Evikon

Evikon E2618-H2S Manuale utente

Evikon

Evikon PluraSens E2611-CH4 Manuale utente

Evikon

Evikon E2618-H2 Manuale utente

Evikon

Evikon PluraSens E2658-NH3-S Manuale utente

Evikon

Evikon PluraSens E2658-PID Manuale utente

Evikon

Evikon PluraSens E2638 Series Manuale utente

Evikon

Evikon E2618-CO2 Manuale utente

Evikon

Evikon PluraSens E2618-O3 Manuale utente

Evikon

Evikon PluraSens E2648-VOC Manuale utente

Evikon

Evikon E2615 Series Manuale utente

Evikon

Evikon PluraSens E2611-NH3 Manuale utente

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente